Equal Tees Adapter AC/AD — Metric Male 24° Cone Run Tee, L and S Series

Why This Equal Tees Adapter Passes the Compliance Gate
On a tee, the branch sees the same pressure as the run and twice the bending moment, so a tee is the weakest point in most tube circuits. Every AC/AD equal tees adapter is bored from a forged body — never from a welded assembly — with the branch axis square to the run axis within the drawing tolerance, the three 24° cone seats machined in one fixturing setup so that the seats are concentric with their own threads, and the branch wall thickness verified by sectioning on the first article of each lot. Threads are gauged 6g go / no-go and the cone seals are profile-checked.
The fitting is a run tee with three metric male 24° cone ends (DIN 2353 / ISO 8434-1) of the same size — an equal tee, not a reducing tee — with the branch at 90° to the run. “AC” is the range that covers the extra-light (LL) and light (L) series; “AD” is the heavy (S) series.
Ventajas principales
- Forged one-piece body. No weld in the pressure path, so no weld porosity, no heat-affected zone and no radiographic inspection requirement.
- Equal bore. All three connections are the same size, so the tee adds almost nothing to the system pressure drop compared with a reducing tee or a pair of adapters.
- Extra-light to heavy class in one family. AC covers tubes 4 to 42 mm at 10 MPa (LL), 25 MPa and 16 MPa (L); AD covers tubes 6 to 38 mm at 63 MPa, 40 MPa and 31.5 MPa (S).
- Three cone seats, one standard. All joints are metric 24° cone, so the tee uses the same tube ends and the same tools as the rest of the circuit.
- Clear identification. Part number, size and material are marked on the body so a service technician can identify a failed tee without a drawing.
Especificaciones técnicas
What Is an Equal Tees Adapter?
It is a three-way hydraulic fitting with one straight run and one perpendicular branch, all three ends being metric male studs with external 24° cones. “Equal” means the three connections are the same nominal size. It splits one flow into two, or combines two flows into one, at a right angle.
The Three Connections — Metric Male 24° Cone
Each end is a metric male stud with an external 24° cone per DIN 2353 / ISO 8434-1 and a 6g metric thread. In the AC range the thread follows the extra-light (LL) or light (L) series; in the AD range it follows the heavy (S) series, one thread size larger for the same tube OD with a heavier wall. Threads run from M8×1 in the LL sizes to M52×2 at the top of the L and S ladders.
This is a 24° cone system and does not interchange with a 60° cone (BSP, DIN 3861 / ISO 1179) or a 37° flare (JIC, ISO 8434-2). The included angles and contact diameters differ, and a mixed joint may pass a static test and leak once the line reaches working temperature.
Equal Tee or Branch Tee with Swivel Nut?
Both fit the same job — three-way flow at 90° — but they assemble differently:
| Feature | Equal tees adapter (AC/AD) | Branch tee with swivel nut (BC/BD) |
|---|---|---|
| Run ends | Male 24° cone studs | Male 24° cone studs |
| Branch end | Male 24° cone stud | Swivel nut with internal 24° cone seat |
| Branch alignment | Set by the torque position of the branch stud | Free — the nut is rotated to suit the tube, then tightened |
| Best for | Rigid manifolds, fixed tube orientation | Pre-bent branch tubes, tight assemblies, service access |
| Wrench access | Three wrenches, one per joint | Two wrenches on the run, then one on the branch nut |
If the branch tube cannot be rotated to match a fixed stud, choose the branch tee with swivel nut; if the branch is a port in a manifold block, the equal tee is the simpler and cheaper part.
Datos dimensionales
In the drawing, E is the thread designation of the connections, D1, D2, D3 the tube outside diameters of the three ports, l1, l2, l3 the stud reaches from each end face to the axis, L1, L2, L3 the overall length of each leg measured along its own axis, S1 the body hex and S2, S3, S4 the end hexes.
The run is dimensioned along one axis (L1 and L3) and the branch along the perpendicular axis (L2). On a tee these two directions are not exchangeable: rotating the body to change the branch direction also changes which leg faces the wrench. Check the branch direction and the two run-leg dimensions, in both the length and the height direction, against your installation drawing.
Tabla completa de dimensiones (matriz de referencias)
Values as published in the HENGHUA catalogue drawing. Dimensions in millimetres.
| N.º DE PIEZA. | HILO E | D1, D2, D3 | l1, l2, l3 | L1, L2, L3 | S1 | S2, S3, S4 | Pressure MPa |
|---|---|---|---|---|---|---|---|
| AC-08 | M8×1 | 4 | 11 | 21 | 9 | 10 | 10 — LL series |
| AC-10 | M10×1 | 5 | 9.5 | 21 | 9 | 12 | 10 — LL series |
| AC-10A | M10×1 | 6 | 9.5 | 21 | 9 | 12 | 10 — LL series |
| AC-12A | M12×1 | 8 | 11.5 | 23 | 12 | 14 | 10 — LL series |
| AC-12 | M12×1.5 | 6 | 12 | 27 | 12 | 14 | 25 — L series |
| AC-14 | M14×1.5 | 8 | 14 | 29 | 12 | 17 | 25 — L series |
| AC-16 | M16×1.5 | 10 | 15 | 30 | 14 | 19 | 25 — L series |
| AC-18 | M18×1.5 | 12 | 17 | 32 | 17 | 22 | 25 — L series |
| AC-22 | M22×1.5 | 15 | 21 | 36 | 19 | 27 | 25 — L series |
| AC-26 | M26×1.5 | 18 | 23.5 | 40 | 24 | 32 | 25 — L series |
| AC-30 | M30×2 | 22 | 27.5 | 44 | 27 | 36 | 16 — L series |
| AC-36 | M36×2 | 28 | 30.5 | 47 | 36 | 41 | 16 — L series |
| AC-45 | M45×2 | 35 | 34.5 | 56 | 41 | 50 | 16 — L series |
| AC-52 | M52×2 | 42 | 40 | 63 | 50 | 60 | 16 — L series |
| AD-14 | M14×1.5 | 6 | 16 | 31 | 12 | 17 | 63 — S series |
| AD-16 | M16×1.5 | 8 | 17 | 32 | 14 | 19 | 63 — S series |
| AD-18 | M18×1.5 | 10 | 17.5 | 34 | 17 | 22 | 63 — S series |
| AD-20 | M20×1.5 | 12 | 21.5 | 38 | 17 | 24 | 63 — S series |
| AD-22 | M22×1.5 | 14 | 22 | 40 | 19 | 27 | 63 — S series |
| AD-24 | M24×1.5 | 16 | 24.6 | 43 | 24 | 30 | 63 — S series |
| AD-30 | M30×2 | 20 | 26.5 | 48 | 27 | 36 | 40 — S series |
| AD-36 | M36×2 | 25 | 30 | 54 | 36 | 46 | 40 — S series |
| AD-42 | M42×2 | 30 | 35.5 | 62 | 41 | 50 | 40 — S series |
| AD-52 | M52×2 | 38 | 41 | 72 | 50 | 60 | 31.5 — S series |
Tabla de tamaños de rosca y guiones
| Tube OD (D1, D2, D3) | Extra-light / light series | Heavy series |
|---|---|---|
| 4 mm | M8×1 (AC-08, 10 MPa) | — |
| 5 mm | M10×1 (AC-10, 10 MPa) | — |
| 6 mm | M10×1 (AC-10A) or M12×1.5 (AC-12) | M14×1.5 (AD-14) |
| 8 mm | M12×1 (AC-12A) or M14×1.5 (AC-14) | M16×1.5 (AD-16) |
| 10 mm | M16×1.5 (AC-16) | M18×1.5 (AD-18) |
| 12 mm | M18×1.5 (AC-18) | M20×1.5 (AD-20) |
| 14 mm | — | M22×1.5 (AD-22) |
| 15 mm | M22×1.5 (AC-22) | — |
| 16 mm | — | M24×1.5 (AD-24) |
| 18 mm | M26×1.5 (AC-26) | — |
| 20 mm | — | M30×2 (AD-30) |
| 22 mm | M30×2 (AC-30) | — |
| 25 mm | — | M36×2 (AD-36) |
| 28 mm | M36×2 (AC-36) | — |
| 30 mm | — | M42×2 (AD-42) |
| 35 mm | M45×2 (AC-45) | — |
| 38 mm | — | M52×2 (AD-52) |
| 42 mm | M52×2 (AC-52) | — |
Note that two different tube sizes can share one thread in the extra-light range — AC-10A and AC-12A are examples — so the part number, not the thread, identifies the tube size you will actually receive.
Material y tratamiento térmico
Carbon steel bodies, forged, hardened according to pressure class and plated with trivalent chromium or zinc-nickel. Stainless 304 / 316L available to order. The three cone seats are produced in one operation so that the branch cone is concentric with the branch thread.
Presión de trabajo y rango de funcionamiento
The pressure column is the working pressure of the connection, not a burst pressure; a 4:1 burst ratio is typical of the body. A tee is a stress concentration: the branch junction of a large-bore tee is the place to check when a circuit is run at its limit. Size the branch for the flow it actually carries — a tee splitting 60/40 has to be sized on the branch side, not the run side.
Rango de temperatura
−40 °C to +120 °C for standard components; to +200 °C with FKM in associated seals. The steel joint itself is not the limiting factor; the tube end and the system fluid usually are.
Cómo interpretar la tabla de referencias
AC-14 reads: family AC (equal tee, extra-light or light series), size 14 = 8 mm tube / M14×1.5 on all three ends. AD-20 is the heavy equivalent: size 20 = 12 mm tube / M20×1.5. The numbers follow the series ladder, not the millimetre tube OD, so always quote the tube size and the thread together when cross-referencing.
Selección y pedido
Selection Checklist / Decision Table
| Requirement | Choose |
|---|---|
| Equal 3-way split, all ports same size | AC or AD |
| Low-pressure pilot, gauge or lubrication line | AC LL (10 MPa) |
| Standard hydraulic run | AC (L series) |
| High pressure or heavy-wall tube | AD (S series) |
| Branch must be oriented to a pre-bent tube | Branch tee with swivel nut BC/BD |
| Different sizes at the branch | Reducing tee — specify all three ends |
Servicio de referencias cruzadas
Send the OEM number, the tube OD and the thread, or a photograph of the tee. We return a mapped part number with the three leg dimensions filled in and confirm which end is the branch.
Embalaje y logística
Threads protected on all three ends, plastic bag, carton, pallet; certificates and inspection reports referenced to the heat number. Air, sea and express shipping available.
Installation and Fitment Guide
Step-by-Step Assembly
- Verify all three ports are metric 24° cone (DIN 2353 / ISO 8434-1) and that the thread size matches the ordered series.
- Clean the three cone seats and the mating ports. Remove swarf, paint and old sealant.
- Lubricate the threads lightly; never apply sealant to a 24° cone.
- Decide the branch direction first. On an equal tee the body position is set by the torque position of the studs, so the branch must end up where the tube run needs it.
- Start all three threads by hand before tightening any of them; then torque the two run ends first, holding the body by the S1 hex.
- Torque the branch end last, using the end hex (S2/S3/S4) and a wrench on the body so the finished joints are not disturbed.
- Re-check all three joints after the first thermal cycle.
Torque and Sealing Notes
Each of the three joints has its own torque value and each is a metal-to-metal 24° cone. Under-torque leaves the cone short of full contact; over-torque deforms the cone and the port. On a tee, the sequence matters as much as the value: tightening the branch first and then fighting the run ends can leave a joint that was correct when it was made and loose when the assembly is finished. Use a torque wrench, not feel.
Advertencias sobre la instalación
- Do not mix 24°, 60° and 37° cone components across the three ports.
- Do not use thread sealant anywhere on this fitting.
- Do not use the tee as a structural support; use a clamp or a bulkhead fitting.
- Do not reuse a cone that has been over-torqued, galled or dented.
- Do not assume three wrenches will fit in a confined space — check access before ordering.
Applications and Industries
Equal tees are used to split supply to two actuators, to combine two return lines, in lubrication and pilot circuits, on press and injection-moulding manifolds, on mobile machinery hydraulic blocks, on marine systems and on test benches. The equal tees adapter is the low-pressure-drop answer whenever two equal flows must be taken from one line.
Personalización OEM y trazabilidad de la calidad
Reducing variants, special leg lengths, special hex, alternative materials and plating are produced to drawing. Incoming material verification, first-article inspection (including sectioning for wall thickness at the branch), thread gauging, cone profile checks, proof pressure testing on sample lots and final inspection are recorded against the order, with EN 10204 3.1 certificates on request.
Preguntas frecuentes
What does “equal” mean? All three connections are the same size. A reducing tee has a smaller branch.
Can I use an equal tee as a manifold? It can split the flow, but it is not a manifold: there is no mounting, no gauge port and no facility to plug an outlet. Use a manifold block where that is needed.
Which end is the branch? The one at 90° to the run. On the drawing it is the leg dimensions along the perpendicular axis (L2 in the catalogue table).
Is the pressure rating the same on all three ends? Yes — the body rating applies to all three connections; the piping attached to each end may have a lower rating.
What is the difference from BC/BD? BC/BD has a swivel nut on the branch so the branch tube can be aligned after the run joints are tight. The AC/AD equal tee has a fixed stud on the branch.
Do I need sealant? No. All three joints are 24° metal cone seats.
Solicitar un presupuesto
Send the part number, the tube OD, the thread series, the material, the quantity and the working pressure. We will confirm the three end sizes, the branch direction and the wall thickness at the branch, and quote with the inspection documentation included.
Related products in this range: branch tee fittings with swivel nut BC/BD · metric male 74° cone tee adapter AQ · metric male O-ring tee adapter AE · 90° elbow fittings adapter 1C9/1D9 · straight fittings adapter 1C/1D.
Explora todo el Adaptadores hidráulicos una gama para toda la familia, o ponte en contacto con nosotros para solicitar un presupuesto, informes de ensayo de fábrica y muestras.
Consulta sobre nuestro producto
Somos un proveedor internacional de accesorios y equipos hidráulicos, y ofrecemos una solución integral de abastecimiento a una amplia variedad de sectores. Nuestros productos incluyen: mangueras hidráulicas, racores, adaptadores, acoplamientos rápidos, conectores, protectores de mangueras, equipos hidráulicos y mucho más: todo lo que necesitas para que tus operaciones funcionen sin problemas y de forma eficiente.
Indíquenos sus necesidades mediante el formulario que aparece a continuación. Nuestro equipo le responderá con asesoramiento especializado y un presupuesto personalizado para garantizar el buen funcionamiento de sus operaciones.
- Manguera hidráulica2323 productos
- Manguera hidráulica en espiral con alambre de acero66 productos
- Manguera hidráulica trenzada con alambre de acero1010 productos
- Manguera hidráulica reforzada con tejido33 productos
- Manguera hidráulica termoplástica33 productos
- Manguera industrial7575 productos
- Manguera de aire99 productos
- Manguera de agua1111 productos
- Manguera de aceite1616 productos
- Manguera para productos químicos66 productos
- Manguera compuesta1616 productos
- Manguera compuesta química33 productos
- Manguera compuesta para uso marítimo55 productos
- Manguera compuesta para petróleo55 productos
- Manguera compuesta para altas temperaturas11 producto
- Manguera compuesta de PTFE11 producto
- Manguera compuesta criogénica11 producto
- Manguera de vapor33 productos
- Manguera multiusos22 productos
- Mangueras para alimentos y bebidas44 productos
- Manguera para hormigón44 productos
- Manguera para cemento22 productos
- Manguera para la manipulación de materiales1111 productos
- Manguera para dragado44 productos
- Accesorios hidráulicos166166 productos
- Accesorios reutilizables para mangueras66 productos
- Racores para mangueras sin casquillo88 productos
- Accesorios hidráulicos JIC1616 productos
- Racores hidráulicos métricos4141 productos
- Racores hidráulicos NPT66 productos
- Racores hidráulicos BSP2626 productos
- Racores hidráulicos SAE3030 productos
- Racores hidráulicos tipo banjo44 productos
- Racores hidráulicos ORFS1111 productos
- Virola1111 productos
- Accesorios con brida2626 productos
- Accesorios de una sola pieza2424 productos
- Adaptadores hidráulicos149149 productos




