BSPT Male Fitting: 13011-SP Series

bspt male fitting 13011 sp spec

Why This BSPT Male Fitting Passes the Compliance Gate

A BSPT male fitting is a crimp-on hose fitting whose port side is a male taper thread from the R series (British Standard Pipe Taper) and whose hose side is a serrated stem crimped onto braided hose. The 13011-SP series from HENGHUA covers 23 part numbers from -02 to -32 with R-series taper threads from R1/8″ to R2″. Every unit is cold-forged from carbon steel, heat-treated, plated, and 100% pressure tested before shipment. For OEM buyers this fitting is a compliance gate; for maintenance teams it is the crimped BSPT termination that gives a factory-grade hose end on taper-thread circuits.

  • BSPT taper thread (R series): the male thread is tapered and seals by thread interference per ISO 7-1, so a thread sealant (PTFE tape or pipe dope) is applied before assembly. An R taper thread must never be interchanged with a parallel G (BSPP) thread, which seals by a cone, washer, or O-ring instead.
  • Crimp termination: the serrated stem is crimped onto the hose with a matching ferrule, giving a permanent, factory-grade hose end for braided constructions.
  • Braided hose executions: the part numbers in the table are for braided hose from -02 to -32; for spiral hose, change the series number to 13012 per the factory sheet.
  • Centre hexagon: the drawing shows one hexagon, S1, between the threaded section and the hose stem, giving a solid wrenching point for tightening and removal.
  • Comprobación de la compuerta del fabricante original (OEM): full dimensional and material conformance with taper thread form per ISO 7-1, with material test reports (MTR) available for every batch.

Ventajas principales

  1. Taper thread seal: the R thread seals by interference, which is the standard taper connection on European-style circuits, air systems, agricultural equipment, and marine hydraulics.
  2. Crimped, factory-grade hose end: the braided hose is permanently attached by crimping, so the assembly carries the rated pressure of the hose.
  3. Twenty-three sizes, R1/8″ to R2″: from -02 instrumentation lines to -32 main lines, the widest BSPT male spread in the range.
  4. Crimp data supplied: every order includes insert depth, crimp outside diameter, and die selection for your hose series.
  5. Opciones de ensayo de niebla salina de 96 a 1.000 h: zinc trivalente (96 h), zinc-níquel (720 h) o Dacromet (1000 h), según el entorno de uso.

Especificaciones técnicas

What Is This BSPT Male Fitting?

This BSPT male fitting joins a braided hose to a male taper thread connection. The port end is a male R-series taper thread (British Standard Pipe Taper, thread form per ISO 7-1): the thread diameter reduces toward the tip, so the flanks wedge together as the fitting is tightened, and the metal-to-metal interference is what seals the joint. Because the seal depends on interference, a thread sealant such as PTFE tape or pipe dope is applied before assembly. This is fundamentally different from a parallel G (BSPP) thread, which is cylindrical and seals by a separate element: a 60° cone, a bonded washer, or an O-ring. An R thread and a G thread are not interchangeable, and the two sealing principles must never be mixed on one joint.

The hose side of the fitting is a serrated stem that is crimped onto the hose with a steel ferrule. Crimping produces a permanent, factory-grade attachment that lets the assembly carry the working pressure of the braided hose, which is why the taper-thread family with crimped ends is used across agricultural and construction machinery, marine hydraulics, air and lubrication systems, and general industrial circuits where R taper ports are specified. The single hexagon S1 sits between the threaded section and the hose stem, giving a firm wrenching point when you tighten the fitting into its port and when you remove it.

The series covers 23 sizes from -02 to -32; the part numbers in the table are for braided hose, and for spiral hose the series number changes to 13012. Rows in the table with the same thread but different stem sizes let you match the port thread to the hose bore you actually run. Confirm your hose construction with our engineers and the matching crimp data sheet is supplied with the order.

Datos dimensionales y roscas

Símbolo Descripción
E BSPT male taper thread (R series, ISO 7-1), R1/8″ to R2″
A Overall length of the fitting, from the thread tip to the shoulder of the hose stem
C Length of the threaded section
S1 Hex across flats, between the threaded section and the hose stem
Guión Hose inside diameter in 1/16″ increments (-02 to -32)
DN Diámetro interior de la manguera en milímetros (de 5 a 50)

Full dimension drawings with A, C, and S1 callouts are supplied as PDF and CAD (STEP/DWG) files. Because this is a crimp fitting, the two process-critical parameters are the hose insert depth and the crimp outside diameter; both are hose-series specific and are listed in the crimp data sheet that accompanies every order.

Tabla completa de dimensiones (matriz de referencias) {#by-tamaño-de-rosca}

Read the table with your taper thread (E) and your hose size (dash). The part number is the order code; copy it directly into your inquiry or purchase order. The pattern is 13011-[thread dash]-[hose dash]SP: for example, 13011-12-12SP has an R3/4″ thread and suits a -12 (20 mm) braided hose.

N.º de referencia. Thread E (BSPT) Diámetro interior de la manguera DN (mm) Guión A (mm) C (mm) S1 (mm)
13011-02-03SP R1/8″x28 5 03 22 10 12
13011-02-04SP R1/8″x28 6 04 22.5 10 12
13011-04-04SP R1/4″x19 6 04 27 14.5 14
13011-04-05SP R1/4″x19 8 05 25 15.4 14
13011-04-06SP R1/4″x19 10 06 27 14.5 17
13011-06-04SP R3/8″x19 6 04 27.5 15 17
13011-06-05SP R3/8″x19 8 05 26.5 15 17
13011-06-06SP R3/8″x19 10 06 27.5 15 17
13011-06-08SP R3/8″x19 12 08 30 15 19
13011-08-06SP R1/2″x14 10 06 34.5 20 22
13011-08-08SP R1/2″x14 12 08 35 20 22
13011-08-10SP R1/2″x14 16 10 38 20 22
13011-08-12SP R1/2″x14 20 12 38 20 27
13011-12-08SP R3/4″x14 12 08 37 20 27
13011-12-10SP R3/4″x14 16 10 38 20 27
13011-12-12SP R3/4″x14 20 12 38.5 20 27
13011-12-16SP R3/4″x14 25 16 39.5 20 32
13011-16-12SP R1″x11 20 12 44 25.5 36
13011-16-16SP R1″x11 25 16 45 25.5 36
13011-20-20SP R1.1/4″x11 32 20 49.5 26.5 46
13011-24-24SP R1.1/2″x11 40 24 51.5 26.5 50
13011-32-24SP R2″x11 40 24 57 30 65
13011-32-32SP R2″x11 50 32 57 30 65

The part numbers shown are for the braided-hose version. For spiral hose, change the series number to 13012, whose stem is longer for the extra reinforcement layers.

Select by Hose Dash Size {#by-hose-size}

Match your hose bore first, then read the thread sizes available for that bore:

Hose Dash Hose I.D. (mm) Available BSPT Threads in the 13011-SP Series
-03 5 R1/8″
-04 6 R1/8″, R1/4″, R3/8″
-05 8 R1/4″, R3/8″
-06 10 R1/4″, R3/8″, R1/2″
-08 12 R3/8″, R1/2″, R3/4″
-10 16 R1/2″, R3/4″
-12 20 R1/2″, R3/4″, R1″
-16 25 R3/4″, R1″
-20 32 R1.1/4″
-24 40 R1.1/2″, R2″
-32 50 R2″

Material y tratamiento térmico

Artículo Opción estándar Opción Premium
Material Acero al carbono de alta resistencia forjado en frío (20#/35#/45#) Acero inoxidable 304 o 316L
Tratamiento térmico Carburación y temple, dureza del núcleo: HRC 20-28 Tratamiento en solución, resistencia estable a la corrosión
Superficie Recubrimiento de zinc trivalente (96 h de prueba de niebla salina) Zinc-níquel (720 h), Dacromet (1000 h) o pasivado
Clase «Thread» R-series gauge-checked Lo mismo, con inspección mediante el calibre de rosca 100%

El forjado en frío conserva el sentido de las fibras del acero, lo que aumenta la resistencia a la fatiga ante las pulsaciones de presión. Cada lote sometido a tratamiento térmico se somete a pruebas de dureza y se registra, por lo que el valor de dureza que figura en el certificado de material (MTR) coincide con el de las piezas que recibes.

Presión de trabajo

Artículo Valoración
Conjunto engarzado Governed by the hose and confirmed per hose assembly test practice; braided hose at these sizes typically carries about 10-40 MPa depending on construction and size
Threaded end (BSPT) Seals by taper thread interference per ISO 7-1 with thread sealant; the joint is rated with the assembly and sealant used
Prueba de fábrica Cada accesorio se somete a una prueba de presión 100% antes de su envío.

Las características técnicas exactas de la combinación de tu número de referencia y manguera se confirman en la ficha técnica y por parte de nuestros ingenieros antes del envío.

Ámbito de funcionamiento de presión y temperatura

Temperatura Retención de la presión
-40 °C 100% de presión nominal
-20 °C 100%
0 °C 100%
+20 °C 100%
+40 °C 100%
+60 °C 100%
+80 °C 100%
+100 °C 100%
+120 °C 100% (system derating governed by hose and elastomer seals elsewhere in the circuit, not by the fitting)

The steel body holds full rated pressure across the whole temperature window. In a crimped assembly the working pressure is governed by the weakest component, normally the hose; use the hose derating curve for the system, and the fitting will not be the limiting part.

Selección y pedido

The 13011-SP BSPT male fitting series covers the crimped taper-thread segment of BSP hydraulic hose fittings, from -02 to -32, so most orders can be placed directly from the table above.

BSPT Thread Size Chart

Use this chart to identify the taper thread on your port. R threads are tapered and are identified by measuring the thread diameter and counting the threads per inch; the taper makes the diameter reduce toward the tip.

BSPT Thread (R) TPI Salpicadero típico de «Hose»
R1/8″ 28 -03 to -04
R1/4″ 19 -04 to -06
R3/8″ 19 -04 to -08
R1/2″ 14 -06 to -12
R3/4″ 14 -08 to -16
R1″ 11 -12 to -16
R1.1/4″ 11 -20
R1.1/2″ 11 -24
R2″ 11 -24 to -32

BSPT vs BSPP Quick Check

R (BSPT) taper threads seal by interference and need PTFE tape or pipe dope. G (BSPP) parallel threads are cylindrical and seal by a cone, washer, or O-ring. The two are not interchangeable, and mixing them on one joint will leak.

Cross Reference Service {#by-oem-part-number}

Most maintenance teams buy against a legacy part number printed on the old drawing. Send us the OEM or distributor part number you currently use, with a photo of the fitting if possible. Our engineers identify the thread, the stem profile, the hose size, and the body configuration, then confirm the exact 13011-SP equivalent before you place the order. The service covers BSPT fittings, BSP hydraulic hose fittings, and the taper-thread ends of your inventory, and interchange confirmation is free. The cross reference sheet is returned in PDF for your records.

Embalaje y logística

Artículo Detalle
Embalaje estándar 10 pcs per box (typical), 100 pcs per carton for small sizes
Peso bruto Calculado por talla y confirmado en la factura proforma
Marcado Etiqueta de la caja con el número de pieza, la cantidad y el número de lote para el control de entrada
Origen Fabricado en China, fábrica de HENGHUA
Documentos de exportación Factura comercial, lista de embalaje, MTR, certificado de conformidad

Guía de montaje y uso

Procedimiento de engastado en cuatro pasos

  1. Corta la manguera en ángulo recto: use a hose cutter, never a hacksaw or an angle grinder. A square, clean end is the precondition for a uniform ferrule grip.
  2. Marca la profundidad de inserción: read the insert depth for your hose series from the crimp data sheet and mark the line on the hose cover.
  3. Lubricar e introducir: apply a thin film of assembly lubricant to the stem and the hose bore, then push the fitting into the hose until the mark meets the ferrule.
  4. Engarzar y comprobar: select the die per the crimp table, crimp in one continuous stroke, then measure the crimp outside diameter with a caliper and compare with the tolerance.

Threading the BSPT End

Wrap PTFE tape clockwise around the taper thread (or apply pipe dope) before assembly. Thread the fitting into the port by hand until the thread bites, then tighten with a wrench on the S1 hexagon. The taper thread seals by interference; do not over-tighten past the manufacturer’s recommended engagement, because the wedge force grows quickly on taper threads.

Advertencias sobre la instalación

  • ❌ Never interchange R (BSPT taper) threads with G (BSPP parallel) threads. They are different sealing systems and are not compatible.
  • ❌ Nunca mezcles racores y casquillos de diferentes proveedores, aunque las medidas de la rosca y de la manguera parezcan idénticas. La geometría del vástago, la dureza del casquillo y los parámetros de engarzado difieren, y una unión mixta presentará fugas o se soltará bajo presión.
  • ❌ Never crimp without the matching crimp data sheet. An under-crimped joint weeps, and an over-crimped joint damages the hose reinforcement.
  • ❌ Never recrimp a fitting after a failed attempt, and never reuse a fitting removed from a hose.
  • ✔ Tras el montaje, somete el circuito a una prueba de presión a 1,5 veces la presión de servicio y comprueba que no haya fugas en todas las uniones.

Personalización OEM y trazabilidad de la calidad

Opciones de personalización

  • Personalización del tamaño y la rosca: non-standard R thread and hose combinations and special stem lengths machined to your drawing.
  • Personalización del tratamiento superficial: trivalent zinc (96 h), zinc-nickel (720 h), or Dacromet (1000 h) salt spray grades.
  • Marcado láser: su logotipo, el número de pieza y el código de lote marcados con láser en el hexágono para garantizar una trazabilidad completa.
  • Opciones de materiales: Acero inoxidable 304/316L para circuitos químicos, marinos y en contacto con alimentos, con certificados de pasivación.

Sistema de calidad y trazabilidad

Cada lote sigue un proceso documentado: recepción del acero con certificado de fábrica → forjado en frío → mecanizado CNC → tratamiento térmico → recubrimiento → inspección de las dimensiones y del calibre de rosca 100% → prueba de presión → marcado láser → embalaje. El número de lote que figura en la caja de cartón remite al lote de materia prima, al registro de tratamiento térmico y al informe de inspección. Se facilitan informes de ensayo de materiales (MTR) con cada pedido previa solicitud, y se pueden tramitar informes de inspección de terceros (BV/SGS) antes del envío.

Preguntas frecuentes

Q: What is a BSPT male fitting? A: It is a crimp-on fitting for braided hose whose port end is a male R-series taper thread (ISO 7-1) and whose hose end is a serrated stem crimped onto the hose.

Q: How does a BSPT thread seal? A: The R thread is tapered, so the flanks wedge together as the fitting is tightened and the metal-to-metal interference seals the joint. Thread sealant such as PTFE tape or pipe dope is applied before assembly.

Q: What is the difference between BSPT (R) and BSPP (G) threads? A: R threads are tapered and seal by thread interference with sealant. G threads are parallel and seal by a separate element: a 60° cone, a bonded washer, or an O-ring. The two are not interchangeable.

Q: What is the difference between the 13011-SP and the 13011-SP(PO) series? A: The 13011-SP is the crimped version for braided hose, 23 sizes from R1/8″ to R2″. The 13011-SP(PO) is the push-on program version, 6 sizes from R1/8″ to R3/4″, for low-pressure lines. Send us your hose and pressure and our engineers will confirm the right version.

Q: Which hoses work with the 13011-SP series? A: The part numbers in the table are for braided hose from -02 to -32 (DN 5 to DN 50). For spiral hose, change the series number to 13012. Confirm your exact hose construction with our engineers, and the matching crimp data sheet will be supplied with the order.

P: ¿Podéis facilitarme los datos de engaste para mi manguera? A: Yes. Every order includes the crimp data sheet for your hose construction, with insert depth, crimp outside diameter, and die selection. Send us your hose series and brand, and our engineers will confirm the crimp parameters before shipment.

Solicitar un presupuesto

Tell us the taper thread, the hose dash size, the hose construction, and the annual quantity. Whether you need stock BSP hydraulic hose fittings for distribution or a custom BSPT male fitting for an OEM program, the quoting process is the same. For replacement orders, send the legacy part number and a photo, and our engineers will confirm the interchange before quoting. Every BSPT male fitting leaves the HENGHUA factory pressure-tested, batch-coded, and backed by a written warranty. Request your quote, crimp data sheet, or drawing pack today, and we will respond within 24 hours.

Consulta sobre nuestro producto

Somos un proveedor internacional de accesorios y equipos hidráulicos, y ofrecemos una solución integral de abastecimiento a una amplia variedad de sectores. Nuestros productos incluyen: mangueras hidráulicas, racores, adaptadores, acoplamientos rápidos, conectores, protectores de mangueras, equipos hidráulicos y mucho más: todo lo que necesitas para que tus operaciones funcionen sin problemas y de forma eficiente.
Indíquenos sus necesidades mediante el formulario que aparece a continuación. Nuestro equipo le responderá con asesoramiento especializado y un presupuesto personalizado para garantizar el buen funcionamiento de sus operaciones.