BSP Male 60° Cone Seat Fitting: 12611 Series

Why This BSP Male 60° Cone Seat Fitting Passes the Compliance Gate

A BSP male 60° cone seat fitting terminates a braided hydraulic hose in a male G-threaded stud whose tip carries an internal 60° cone seat. It is the male half of the BSPP 60° cone connection: a female swivel fitting with a 60° cone (as on our 22611 series) is screwed onto the male thread, and its cone is drawn into this fitting’s cone seat to form a metal-to-metal seal. The 12611 series from HENGHUA covers 19 part numbers from -02 to -32 with G-series parallel threads from G1/8″ to G2″. Every unit is cold-forged from carbon steel, heat-treated, plated, and 100% pressure tested before shipment. For OEM buyers this fitting is a compliance gate; for maintenance teams it is the male cone seat termination that turns a hose end into the stud side of a BSP 60° cone joint.

• Internal 60° cone seat: the tip of the male thread carries a machined internal (concave) 60° cone seat. When a female swivel 60° cone end is tightened onto the thread, the mating cone seats into this recess and the two metal faces seal without an O-ring.
• BSPP G thread: the thread is parallel (G series, ISO 228-1) and only holds the connection; the cone seat does the sealing. G threads must never be interchanged with BSPT taper threads, which seal by thread interference.
• Wrenching hexagon: the drawing shows one hexagon, S1, between the threaded section and the hose tail, so the fitting can be held firmly while the female nut is torqued against it.
• Braided hose executions: the part numbers in the table are for braided hose from -02 to -32; for spiral hose, change the series number to 12612 per the factory sheet.
• OEM gate check: full dimensional and material conformance with G thread form per ISO 228-1, with material test reports (MTR) available for every batch.

Core Advantages

1. The cone seat side of the joint: if your circuit mates female swivel 60° cone ends, this fitting provides the matching male thread and cone seat, so the hose assembly carries the stud side of the connection.
2. Metal-to-metal cone seal: the cone-to-seat contact seals without washers or O-rings in the standard version, removing a soft element from the pressure path.
3. Nineteen sizes, G1/8″ to G2″: from -02 instrumentation lines to -32 main lines, matched to the female 60° cone swivel range.
4. Single hexagon for installation: the S1 hex sits between thread and tail, giving a solid wrenching point when you tighten the mating female nut.
5. 96 to 1000 h salt spray options: trivalent zinc (96 h), zinc-nickel (720 h), or Dacromet (1000 h), matched to your environment.

Especificaciones técnicas

What Is This BSP Male 60° Cone Seat Fitting?

This BSP male 60° cone seat fitting terminates a braided hose in the male stud side of the BSP 60° cone connection. The port end is a male parallel G thread (G series, thread form per ISO 228-1); at the tip of the thread, the fitting carries a machined internal (concave) 60° cone seat. The other end is a hose tail that is crimped onto the hose. When a female swivel fitting with a 60° cone is tightened onto the male thread, the mating cone is drawn into this fitting’s internal cone seat and the two metal faces meet in a metal-to-metal seal. The G thread is parallel and does not seal by interference; it only pulls the cone into the seat. This is why a 60° cone seat must never be paired with a BSPT taper thread, which seals by thread interference instead.

The 12611 is the male counterpart of the female 60° cone swivel fittings in our catalog. The female side (for example the 22611 series straight fittings and the 22641/22691 elbows) carries a swivel nut with an internal G thread and a convex 60° cone on the body; the male side (this series) carries the external G thread and the concave cone seat that receives it. Buying both halves from the same catalog means the cone geometry, thread sizes, and seal faces are matched by design. The single hexagon S1 sits between the threaded section and the hose tail, giving a firm wrenching point while the female nut is torqued.

Use this male fitting when the mating component is a female swivel 60° cone end. The series covers 19 sizes from -02 to -32; the part numbers in the table are for braided hose, and for spiral hose the series number changes to 12612. The hose tail is engineered for a crimped termination; confirm your exact hose construction with our engineers and the matching crimp data sheet is supplied with the order.

Dimensional Data and Threads

Full dimension drawings with A, C, and S1 callouts are supplied as PDF and CAD (STEP/DWG) files. Because this is a crimp fitting, the two process-critical parameters are the hose insert depth and the crimp outside diameter; both are hose-series specific and are listed in the crimp data sheet that accompanies every order.

Full Dimension Table (Part Number Matrix) {#by-thread-size}

Read the table with your BSPP thread (E) and your hose size (dash). The part number is the order code; copy it directly into your inquiry or purchase order. The pattern is 12611-[thread dash]-[hose dash]: for example, 12611-12-12 has a G3/4″ thread and suits a -12 (20 mm) braided hose.

The part numbers shown are for the braided-hose version. For spiral hose, change the series number to 12612, whose stem is longer for the extra reinforcement layers.

Select by Hose Dash Size {#by-hose-size}

Match your hose bore first, then read the thread sizes available for that bore:

Material and Heat Treatment

Cold forging preserves the grain flow of the steel, which raises fatigue resistance under pressure pulsation. Each heat-treatment batch is hardness-tested and recorded, so the hardness number on the MTR matches the parts you receive.

Presión de trabajo

The exact rating for your part number and hose combination is confirmed on the datasheet and by our engineers before shipment.

Pressure-Temperature Operating Envelope

The steel cone seat and body hold full rated pressure across the whole temperature window. In a crimped assembly the working pressure is governed by the weakest component, normally the hose; use the hose derating curve for the system, and the fitting will not be the limiting part.

Selection and Ordering

The 12611 BSP male 60° cone seat fitting series covers the male cone seat segment of BSP hydraulic hose fittings, from -02 to -32, so most orders can be placed directly from the table above.

BSPP Thread Size Chart

Use this chart to identify the thread on your port. BSPP G threads are parallel; they are identified by measuring the thread outside diameter and counting the threads per inch.

Cross Reference Service {#by-oem-part-number}

Most maintenance teams buy against a legacy part number printed on the old drawing. Send us the OEM or distributor part number you currently use, with a photo of the fitting if possible. Our engineers identify the thread, the cone seat geometry, the hose size, and the body configuration, then confirm the exact 12611 equivalent before you place the order. The service covers 60° cone fittings, BSP hydraulic hose fittings, and the male stud ends of your inventory, and interchange confirmation is free. The cross reference sheet is returned in PDF for your records.

Packaging and Logistics

Assembly and Use Guide

Four-Step Crimping Procedure

1. Cut the hose square: use a hose cutter, never a hacksaw or an angle grinder. A square, clean end is the precondition for a uniform ferrule grip.
2. Mark the insert depth: read the insert depth for your hose series from the crimp data sheet and mark the line on the hose cover.
3. Lubricate and insert: apply a thin film of assembly lubricant to the stem and the hose bore, then push the fitting into the hose until the mark meets the ferrule.
4. Crimp and verify: select the die per the crimp table, crimp in one continuous stroke, then measure the crimp outside diameter with a caliper and compare with the tolerance.

Connecting the 60° Cone Seat End

On the BSP male 60° cone seat fitting, clean the internal cone seat and the cone of the mating female swivel fitting with a lint-free cloth. Hold the S1 hexagon with a wrench and thread the female nut onto the male G thread by hand until the cone touches the seat, then tighten to the torque listed for the thread size. The 60° cone contact does the sealing, so no sealant is applied to the cone faces. If your circuit uses the O-ring variant of the 60° cone family, fit the correct O-ring before assembly; do not mix the O-ring and plain cone versions.

Installation Warnings

• ❌ Never mix fittings and ferrules from different suppliers, even when the thread and hose sizes look identical. Stem geometry, ferrule hardness, and crimp parameters differ, and a mixed joint will leak or blow off under pressure.
• ❌ Never confuse G (BSPP parallel) threads with R (BSPT taper) threads. A G thread with a 60° cone seat seals by cone contact; a taper thread seals by thread interference and needs sealant. The two are not interchangeable.
• ❌ Never match a cone seat to a scratched or pitted mating cone. The metal-to-metal seal needs an undamaged sealing surface on both sides.
• ❌ Never crimp without the matching crimp data sheet. An under-crimped joint weeps, and an over-crimped joint damages the hose reinforcement.
• ❌ Never recrimp a fitting after a failed attempt, and never reuse a fitting removed from a hose.
• ✔ After assembly, pressure-test the circuit at 1.5x working pressure and inspect all joints for weepage.

OEM Customization and Quality Traceability

Customization Options

• Size and thread customization: non-standard G thread and hose combinations and special stem lengths machined to your drawing.
• Surface treatment customization: trivalent zinc (96 h), zinc-nickel (720 h), or Dacromet (1000 h) salt spray grades, selected by your environment and corrosion specification.
• Laser marking: your logo, part number, and batch code laser-marked on the hex for full field traceability.
• Material options: 304/316L stainless for chemical, marine, and food-contact circuits, with passivation certificates.

Quality and Traceability System

Every batch follows a documented flow: incoming steel with mill certificate → cold forging → CNC machining → heat treatment → plating → 100% thread gauge and dimension inspection → pressure test → laser marking → packing. The batch number on the carton links back to the raw material lot, the heat-treatment record, and the inspection report. Material test reports (MTR) are provided with every order on request, and third-party inspection reports (BV/SGS) can be arranged before shipment.

FAQ

Q: What is a BSP male 60° cone seat fitting? A: It is a crimp-on fitting for braided hose whose port end is a male parallel G thread (ISO 228-1); the tip of the thread carries an internal 60° cone seat that receives the cone of a female swivel 60° cone end.

Q: How does the connection seal? A: A female swivel fitting with a 60° cone is screwed onto the male thread, and the cone is drawn into the internal cone seat. The two metal faces meet in a metal-to-metal seal; the G thread only holds the connection.

Q: What is the difference between this male fitting and the female 60° cone swivel fittings? A: The female swivel fittings (for example the 22611 series) carry the nut with the internal G thread and the convex cone. This male series carries the external G thread and the concave cone seat that receives it. The two are the matching halves of the same BSPP 60° cone joint.

Q: Which hoses work with the 12611 series? A: The part numbers in the table are for braided hose from -02 to -32 (DN 5 to DN 50). For spiral hose, change the series number to 12612. Confirm your exact hose construction with our engineers, and the matching crimp data sheet will be supplied with the order.

Q: How do I identify a 60° cone seat male end? A: Measure the thread: parallel G threads have 28, 19, 14, or 11 TPI depending on size. Look into the thread tip for a machined 60° cone seat recess. Never confuse it with a flat seat or a tapered BSPT thread.

Q: Can you provide crimp data for my hose? A: Yes. Every order includes the crimp data sheet for your hose construction, with insert depth, crimp outside diameter, and die selection. Send us your hose series and brand, and our engineers will confirm the crimp parameters before shipment.

Solicitar un presupuesto

Tell us the BSPP thread, the hose dash size, the hose construction, and the annual quantity. Whether you need stock BSP hydraulic hose fittings for distribution or a custom 60° cone fitting for an OEM program, the quoting process is the same. For replacement orders, send the legacy part number and a photo, and our engineers will confirm the interchange before quoting. Every BSP male 60° cone seat fitting leaves the HENGHUA factory pressure-tested, batch-coded, and backed by a written warranty. Request your quote, crimp data sheet, or drawing pack today, and we will respond within 24 hours.