20211 Metric Female Flat-Seat Hydraulic Hose Fittings (Swivel Nut)

metric female flat seat hydraulic hose fitting 20211 series spec

Metric female flat-seat hydraulic hose fittings are the swivel-nut end of the flat-seal system: a female metric thread that turns freely on the hose tail, so you can tighten the connection without twisting the hose. The 20211 series covers 27 part numbers from DN4 (-02) to DN50 (-32), with female metric threads from M10x1 to M64x2 and a flat sealing seat, designed for wire-braided hose. If your machine connects hoses onto male metric flat-face studs – or your assemblers fight hose twist on every install – this page gives you the full reference: dimensions, part numbers, the T-variant question and OEM options.

Why Choose These Female Flat-Seat Fittings

  • Porca giratória que roda livremente. The nut rotates on the hose tail, so the connection tightens onto the male stud without winding the hose or fighting the assembly position.
  • Flat-seat sealing system. The flat seat mates with a metric male flat-face stud in the flat-seal family, with the seal element compressed between the two faces.
  • The widest bore coverage in the range. From tiny M10x1 (DN4) control lines to M64x2 (DN50) return lines – 27 sizes in one series.
  • Pronto para OEM. Laser marking, custom plating, material test reports and batch traceability, with both 20211 and 20211-T constructions available.

Normas e rastreabilidade. Threads are ISO 724 metric threads. The series follows the metric female flat-seat configuration used across the widely adopted Chinese 10-series hose fitting numbering system (the female companion to the flat-seal male stud ends). Fittings are designed to pair with wire-braided hose built to EN 853 1SN/2SN or SAE 100 R1AT/R2AT performance classes. Dimensional inspection reports and material test certificates are available for OEM gate checks.

Swivel Nut and Flat Seat: How This Fitting Works

Two features define this series, and both solve real assembly problems.

The swivel nut. The female nut is not fixed to the hose tail – it swivels. When you connect the hose assembly to a male stud on a pump, valve or cylinder, you hold the nut and turn only the nut, not the whole hose. That matters more than it sounds: a fixed female end forces the operator to twist the hose assembly as the thread tightens, which stresses the hose, the crimp and the seal, and makes routing harder. With a swivel, the hose stays exactly where you routed it.

The flat seat. The sealing face of this fitting is flat, and it is designed to mate with a metric male flat-face stud – the flat-seal family that includes the 10311-type male ends. The seal element (an O-ring or a bonded seal, depending on the port system) is compressed between the two flat faces as the swivel nut is torqued, which is why the flat faces must be clean and the seal element must be present. If your male stud instead carries a 24-degree cone or a 60-degree cone, this flat-seat female will not seal on it – the flat system and the cone systems are separate families.

20211 vs 20211-T: what does the T mean?

Rows marked with a T use a different nut and collar construction, shown on the manufacturer drawing, for the same thread and bore combination. Functionally both are metric female flat-seat swivel ends; the T construction is the version your drawing specifies for those sizes. Order the exact part number – with or without T – as printed on your drawing or the old fitting, and we will confirm the construction before dispatch.

Flat seat vs cone seat: a quick check for female ends

Female end type Sealing partner Typical male stud family Our series
Flat seat (this page) Male flat-face stud + seal element Metric flat-seal males (10311 family) 20211 / 20211-T
24-degree cone seat Male 24-degree cone DIN/ISO cone males (10411/10511 family) Separate series
60-degree cone seat Male 60-degree cone 10611-type males Separate series

If the old fitting or the port is unclear, send a photo of the male stud it connects to – the shape of the sealing face decides the correct female series.

20211 Series Technical Specifications

Materiais e processamento

  • Opções de material da carroçaria: aço ao carbono de alta resistência (classes 20#/35#/45#, moldado a frio ou maquinado) como padrão; aço inoxidável 304 ou 316L disponível para ambientes corrosivos ou sujeitos a lavagem.
  • Tratamento de superfícies: Zinco por galvanização como padrão; estão disponíveis revestimentos de zinco amarelo, branco ou preto, zinco-níquel e Dacromet para requisitos mais exigentes em termos de ensaio de névoa salina.
  • Tratamento térmico: hardness and case depth are controlled per drawing to keep the thread, the seat and the nut fatigue-resistant; typical surface hardness range HRC 20-28 (confirm the exact code on your drawing or PO).

Tabela completa de dimensões e referências

All linear dimensions are in millimeters. E = thread, DN = hose bore, A and C = lengths per the supplier drawing, S2 = swivel nut hex across flats. Part numbers ending in T use the alternate nut-and-collar construction shown on the drawing.

N.º de referência Tópico E Diâmetro nominal (DN) da mangueira (mm) Tamanho do traço A (mm) C (mm) Porca sextavada S2 (mm)
20211-10-02 M10x1 4 -02 14.0 6.0 14
20211-12-03 M12x1.25 5 -03 14.0 8.0 17
20211-14-04 M14x1,5 6 -04 15.5 8.5 19
20211-14-05 M14x1,5 8 -05 15.5 8.5 19
20211-16-04 M16x1,5 6 -04 16.5 8.0 22
20211-16-05 M16x1,5 8 -05 16.5 8.0 22
20211-16-06 M16x1,5 10 -06 16.5 8.0 22
20211-18-05T M18x1,5 8 -05 17.5 8.0 24
20211-18-06 M18x1,5 10 -06 17.5 8.0 24
20211-20-06T M20x1.5 10 -06 16.0 10.0 24
20211-20-08 M20x1.5 12 -08 18.5 10.0 27
20211-22-06T M22x1,5 10 -06 16.0 10.0 27
20211-22-08 M22x1,5 12 -08 18.5 10.0 27
20211-22-10 M22x1,5 16 -10 19.5 10.0 27
20211-24-08T M24x1.5 12 -08 16.5 11.0 30
20211-24-10 M24x1.5 16 -10 20.5 10.5 30
20211-27-08T M27x1,5 12 -08 18.5 10.0 32
20211-27-10T M27x1,5 16 -10 19.5 10.0 32
20211-30-12 M30x1.5 20 -12 21.5 11.0 36
20211-33-14 M33x2 22 -14 21.5 13.0 41
20211-36-12T M36x2 20 -12 20.0 13.0 41
20211-36-14T M36x2 22 -14 20.0 13.0 41
20211-39-16T M39x2 25 -16 23.5 13.0 46
20211-42-20 M42x2 32 -20 26.0 15.0 50
20211-45-20T M45x2 32 -20 25.0 15.0 55
20211-52-24T M52x2 40 -24 25.0 17.0 60
20211-60-28T M60x2 45 -28 26.0 20.0 70
20211-64-32T M64x2 50 -32 26.0 23.0 75

Full dimensioned CAD drawings are available on request so your engineers can verify every length and the nut construction before you commit a batch.

Pressão de trabalho: a resposta sincera de que os engenheiros precisam

A crimp hose assembly fails at its weakest link, so the rating of a 20211 fitting depends on the hose you pair it with and the crimp quality. Wire-braided hydraulic hose in this size range typically operates between roughly 80 and 400 bar depending on bore size and construction (1SN or 2SN). Send us your hose specification and we will confirm the working pressure, burst margin and the recommended ferrule for your exact hose brand – the check is free and takes one message. For derating at elevated temperature, follow the hose manufacturer’s pressure-temperature curve, because the rubber cover and tube lose capacity above about +100°C.

Which Fitting Series Do You Need: 20211 (Braided) or 20212 (Spiral)?

O número de referência varia consoante a construção da mangueira, uma vez que a geometria da espiga e os parâmetros de crimpagem são diferentes.

Tipo de mangueira Construção Séries por encomenda
Mangueira com malha metálica 1SN / 2SN (tranças de um ou dois fios), ou SAE 100 R1AT / R2AT 20211-XX-XX
Mangueira em espiral Reforço em espiral do tipo 4SP / 4SH 20212-XX-XX

Em caso de dúvida, verifique a etiqueta da mangueira: as mangueiras trançadas estão identificadas com 1SN, 2SN ou R1AT, R2AT; as mangueiras em espiral estão identificadas com 4SP, 4SH ou semelhante.

Decodificador de números de referência e como encomendar

The 20211 part number carries the whole specification, so purchasing can copy it straight into a PO:

20211 – 22 – 08

  • 20211 = metric female flat-seat swivel series for braided hose
  • 22 = thread nominal size (here M22x1.5 female)
  • 08 = tamanho da mangueira (aqui DN12, diâmetro nominal de 1/2 polegada)
  • T suffix = alternate nut-and-collar construction for that size

Because one thread size can serve several hose bores, always quote both the thread size and the dash size. If you are replacing an existing fitting, send us a photo of the nut end, the hose side and the male stud it connects to, and we will confirm the matching part number the same day. This service is the fastest way to convert an unreadable old part number into a confirmed 20211 order – and it also tells you whether your connection is flat-seat or cone-seat.

Guia de montagem: Quatro passos para uma crimpagem fiável

These fittings are crimp-style hose ends with a swivel nut on the port end. Follow the four steps below on every assembly.

Passo 1 – Corte a mangueira em ângulo reto. Utilize um cortador de mangueira afiado ou uma serra de corte. Um corte reto e limpo permite que a virola se fixe uniformemente na cobertura. Um corte biselado ou irregular é a causa mais comum de falhas por arrancamento.

Passo 2 – Preparar a profundidade de inserção. Empurre a extremidade do encaixe para dentro da mangueira até que encoste firmemente no ressalto interno. A extremidade da mangueira deve ficar na profundidade máxima de inserção, sem ficar curta, caso contrário a zona de crimpagem ficará incorreta.

Passo 3 – Lubrificar e inserir. Apply a thin film of assembly lubricant to the hose bore and the barb. Push the fitting in with a steady twisting motion until it bottoms out, then wipe away excess lubricant. Keep the swivel nut free of lubricant on its sealing face.

Passo 4 – Fixar e verificar. Prenda a virola correspondente de acordo com as especificações de fixação do fabricante da mangueira. Após a fixação, meça sempre o diâmetro exterior da fixação com um paquímetro e compare-o com a tabela de fixação. O valor medido deve situar-se dentro da banda de tolerância permitida. Se estiver fora da tolerância, não coloque o conjunto em serviço – corte-o e volte a crimpá-lo com uma configuração corrigida.

Avisos: três erros que provocam fugas e explosões

  • Never mix flat-seat and cone-seat systems. This flat-seat female will not seal on a 24-degree or 60-degree cone male, even when the thread fits.
  • Never forget the seal element. The flat faces seal by compressing an O-ring or bonded seal between them; without it, or with a damaged one, the joint leaks.
  • Never put PTFE tape or sealant on the thread, and never use the swivel nut as a wrench handle to force a misaligned connection.

Aplicações típicas

The metric female flat-seat swivel appears wherever hoses connect onto male flat-face metric studs and the installer needs the hose to stay put while the nut turns:

  • Hose assemblies onto pump, valve and cylinder ports with metric flat-face male studs
  • Control lines from DN4 up to large return lines at DN50
  • Machine tools, presses, plastic and die-casting machinery
  • Construction, mining and agricultural equipment
  • Unidades de potência hidráulica e hidráulica industrial em geral

Wherever the mating stud is a metric flat-face male, the 20211 series is the female hose end – and the swivel nut keeps your routing exactly where you set it.

Personalização OEM e rastreabilidade da qualidade

For equipment builders and large maintenance programs, the 20211 series can be adapted to your exact drawing and your traceability rules.

Opções de personalização

  • Rosca e geometria: roscas especiais, comprimentos modificados e configurações não normalizadas, usinadas de acordo com o seu desenho ou com base numa amostra.
  • Tratamento de superfícies: zinco-níquel, Dacromet ou outros revestimentos para níveis mais elevados de resistência ao teste de névoa salina; confirmamos as horas de teste alcançadas para o revestimento que escolher, em vez de indicarmos um valor genérico.
  • Marcação a laser: o seu logótipo, o número de peça e o código de lote ou de data, marcados a laser na porca ou na porca hexagonal, para garantir a rastreabilidade total no terreno.
  • Material: versões em aço inoxidável 304/316L para meios corrosivos ou para aplicações que exijam lavagem com jato de água.
  • Embalagem e preparação de kits: etiquetas personalizadas, códigos de barras, quantidades por saco de plástico ou caixa e conjuntos completos de mangueiras.

Documentação de qualidade

  • Rastreabilidade do número de lote: cada encomenda possui um código de lote que remete para os registos de produção.
  • Estão disponíveis relatórios de ensaio de materiais (MTR) para os lotes de aço ao carbono e de aço inoxidável.
  • Relatórios de inspeção dimensional para verificações de portas por parte dos fabricantes de equipamento original (OEM).
  • É possível organizar uma inspeção por uma entidade independente (BV, SGS ou similar) antes do envio.

Amostras e quantidade mínima de encomenda. As amostras dos tamanhos em stock são enviadas rapidamente e mantemos quantidades mínimas de encomenda (MOQ) baixas para os números de referência padrão, para que os distribuidores possam testar a série sem imobilizar capital. Os programas OEM podem passar a entregas programadas assim que o desenho for aprovado.

Embalagem e Logística

Standard export packing: fittings are individually poly-bagged or boxed to protect threads, sealing seats and swivel nuts, then packed in export cartons labeled with part number, quantity and batch code. Custom labeling, kitting and barcode requirements are available. Exact carton quantity, gross weight and CBM are confirmed on the packing list for every order.

Perguntas Frequentes

Q: What is a metric female flat-seat hydraulic hose fitting? A: It is a crimp-style hose end with a female metric thread and a flat sealing seat, fitted with a swivel nut that turns freely on the hose tail. It connects onto a metric male flat-face stud in the flat-seal system.

Q: What does the swivel nut do? A: The nut rotates on the hose tail, so you tighten the connection by turning only the nut. The hose stays where you routed it, without twisting or stressing the assembly.

Q: What is the difference between 20211 and 20211-T? A: Rows marked T use an alternate nut-and-collar construction, shown on the manufacturer drawing, for the same thread and bore combination. Order the exact part number your drawing specifies.

Q: What is the difference between 20211 and 20212 series? A: 20211 is for wire-braided hose (1SN/2SN or R1AT/R2AT) and 20212 is for spiral hose (4SP/4SH style).

Q: Which male stud does this fitting connect to? A: A metric male stud with a flat face in the flat-seal system, sealed by an O-ring or bonded seal compressed between the faces. It is not designed for 24-degree or 60-degree cone males.

P: Preciso de fita para roscas ou de vedante? A: No. The flat faces seal through the seal element. Tape on a straight metric thread adds nothing and can contaminate the system.

P: Qual é a pressão de serviço destas peças de ligação? R: A classificação da montagem depende da mangueira, da virola e da qualidade da crimpagem. Envie-nos as especificações da sua mangueira e iremos confirmar a pressão de serviço e a virola recomendada para a sua combinação.

P: É possível criar referências de peças personalizadas com o meu logótipo? A: Yes. We offer laser marking, custom plating, stainless versions and special dimensions, with MTR and batch traceability for OEM programs.

Order Today: Metric Female Flat-Seat Fittings with Confirmed Fit

Every 20211 metric female flat-seat hydraulic hose fitting in this range is made to controlled dimensions, inspected before packing and backed by batch traceability. Send us your hose type, thread size and a photo of the male stud it connects to, and you will get a confirmed part number, the right construction (with or without T), a delivery date and a quote within one working day. Request samples first and test the swivel on your own bench – turning the nut instead of twisting the hose is the fastest way to feel the difference. We make sure the fitting, ferrule and hose work as one leak-free assembly.

Pedido de informação sobre o nosso produto

Somos um fornecedor global de acessórios e equipamentos hidráulicos, servindo uma vasta gama de setores com uma solução de abastecimento «tudo num só local». Os nossos produtos incluem mangueiras hidráulicas, acessórios, adaptadores, acoplamentos rápidos, conectores, protetores de mangueira, equipamento hidráulico e muito mais — tudo o que precisa para garantir que as suas operações decorram de forma harmoniosa e eficiente.
Indique-nos as suas necessidades através do formulário abaixo. A nossa equipa irá responder-lhe com orientação especializada e um orçamento personalizado para garantir o bom funcionamento das suas operações.