BSPT Male Fitting: 13011-SP Series

bspt male fitting 13011 sp spec

Why This BSPT Male Fitting Passes the Compliance Gate

A BSPT male fitting is a crimp-on hose fitting whose port side is a male taper thread from the R series (British Standard Pipe Taper) and whose hose side is a serrated stem crimped onto braided hose. The 13011-SP series from HENGHUA covers 23 part numbers from -02 to -32 with R-series taper threads from R1/8″ to R2″. Every unit is cold-forged from carbon steel, heat-treated, plated, and 100% pressure tested before shipment. For OEM buyers this fitting is a compliance gate; for maintenance teams it is the crimped BSPT termination that gives a factory-grade hose end on taper-thread circuits.

  • BSPT taper thread (R series): the male thread is tapered and seals by thread interference per ISO 7-1, so a thread sealant (PTFE tape or pipe dope) is applied before assembly. An R taper thread must never be interchanged with a parallel G (BSPP) thread, which seals by a cone, washer, or O-ring instead.
  • Crimp termination: the serrated stem is crimped onto the hose with a matching ferrule, giving a permanent, factory-grade hose end for braided constructions.
  • Braided hose executions: the part numbers in the table are for braided hose from -02 to -32; for spiral hose, change the series number to 13012 per the factory sheet.
  • Centre hexagon: the drawing shows one hexagon, S1, between the threaded section and the hose stem, giving a solid wrenching point for tightening and removal.
  • Verificação do portão OEM: full dimensional and material conformance with taper thread form per ISO 7-1, with material test reports (MTR) available for every batch.

Principais vantagens

  1. Taper thread seal: the R thread seals by interference, which is the standard taper connection on European-style circuits, air systems, agricultural equipment, and marine hydraulics.
  2. Crimped, factory-grade hose end: the braided hose is permanently attached by crimping, so the assembly carries the rated pressure of the hose.
  3. Twenty-three sizes, R1/8″ to R2″: from -02 instrumentation lines to -32 main lines, the widest BSPT male spread in the range.
  4. Crimp data supplied: every order includes insert depth, crimp outside diameter, and die selection for your hose series.
  5. Opções de ensaio de névoa salina de 96 a 1000 h: zinco trivalente (96 h), zinco-níquel (720 h) ou Dacromet (1000 h), de acordo com o seu ambiente.

Especificações Técnicas

What Is This BSPT Male Fitting?

This BSPT male fitting joins a braided hose to a male taper thread connection. The port end is a male R-series taper thread (British Standard Pipe Taper, thread form per ISO 7-1): the thread diameter reduces toward the tip, so the flanks wedge together as the fitting is tightened, and the metal-to-metal interference is what seals the joint. Because the seal depends on interference, a thread sealant such as PTFE tape or pipe dope is applied before assembly. This is fundamentally different from a parallel G (BSPP) thread, which is cylindrical and seals by a separate element: a 60° cone, a bonded washer, or an O-ring. An R thread and a G thread are not interchangeable, and the two sealing principles must never be mixed on one joint.

The hose side of the fitting is a serrated stem that is crimped onto the hose with a steel ferrule. Crimping produces a permanent, factory-grade attachment that lets the assembly carry the working pressure of the braided hose, which is why the taper-thread family with crimped ends is used across agricultural and construction machinery, marine hydraulics, air and lubrication systems, and general industrial circuits where R taper ports are specified. The single hexagon S1 sits between the threaded section and the hose stem, giving a firm wrenching point when you tighten the fitting into its port and when you remove it.

The series covers 23 sizes from -02 to -32; the part numbers in the table are for braided hose, and for spiral hose the series number changes to 13012. Rows in the table with the same thread but different stem sizes let you match the port thread to the hose bore you actually run. Confirm your hose construction with our engineers and the matching crimp data sheet is supplied with the order.

Dados dimensionais e roscas

Símbolo Descrição
E BSPT male taper thread (R series, ISO 7-1), R1/8″ to R2″
A Overall length of the fitting, from the thread tip to the shoulder of the hose stem
C Length of the threaded section
S1 Hex across flats, between the threaded section and the hose stem
Traço Hose inside diameter in 1/16″ increments (-02 to -32)
DN Hose inside diameter in millimetres (5 to 50)

Full dimension drawings with A, C, and S1 callouts are supplied as PDF and CAD (STEP/DWG) files. Because this is a crimp fitting, the two process-critical parameters are the hose insert depth and the crimp outside diameter; both are hose-series specific and are listed in the crimp data sheet that accompanies every order.

Tabela completa de dimensões (matriz de referências) {#by-thread-size}

Read the table with your taper thread (E) and your hose size (dash). The part number is the order code; copy it directly into your inquiry or purchase order. The pattern is 13011-[thread dash]-[hose dash]SP: for example, 13011-12-12SP has an R3/4″ thread and suits a -12 (20 mm) braided hose.

N.º da peça. Thread E (BSPT) Diâmetro interno da mangueira DN (mm) Traço A (mm) C (mm) S1 (mm)
13011-02-03SP R1/8″x28 5 03 22 10 12
13011-02-04SP R1/8″x28 6 04 22.5 10 12
13011-04-04SP R1/4″ x 19 6 04 27 14.5 14
13011-04-05SP R1/4″ x 19 8 05 25 15.4 14
13011-04-06SP R1/4″ x 19 10 06 27 14.5 17
13011-06-04SP R3/8″ x 19 6 04 27.5 15 17
13011-06-05SP R3/8″ x 19 8 05 26.5 15 17
13011-06-06SP R3/8″ x 19 10 06 27.5 15 17
13011-06-08SP R3/8″ x 19 12 08 30 15 19
13011-08-06SP R1/2″ x 14 10 06 34.5 20 22
13011-08-08SP R1/2″ x 14 12 08 35 20 22
13011-08-10SP R1/2″ x 14 16 10 38 20 22
13011-08-12SP R1/2″ x 14 20 12 38 20 27
13011-12-08SP R3/4″ x 14 12 08 37 20 27
13011-12-10SP R3/4″ x 14 16 10 38 20 27
13011-12-12SP R3/4″ x 14 20 12 38.5 20 27
13011-12-16SP R3/4″ x 14 25 16 39.5 20 32
13011-16-12SP R1″ x 11 20 12 44 25.5 36
13011-16-16SP R1″ x 11 25 16 45 25.5 36
13011-20-20SP R1,1/4″ x 11 32 20 49.5 26.5 46
13011-24-24SP R1,1/2″ x 11 40 24 51.5 26.5 50
13011-32-24SP R2″ x 11 40 24 57 30 65
13011-32-32SP R2″ x 11 50 32 57 30 65

The part numbers shown are for the braided-hose version. For spiral hose, change the series number to 13012, whose stem is longer for the extra reinforcement layers.

Selecionar por tamanho do traço da mangueira {#by-hose-size}

Match your hose bore first, then read the thread sizes available for that bore:

Hose Dash Diâmetro interno da mangueira (mm) Available BSPT Threads in the 13011-SP Series
-03 5 R1/8″
-04 6 R1/8″, R1/4″, R3/8″
-05 8 R1/4″, R3/8″
-06 10 R1/4″, R3/8″, R1/2″
-08 12 R3/8″, R1/2″, R3/4″
-10 16 R1/2″, R3/4″
-12 20 R1/2″, R3/4″, R1″
-16 25 R3/4″, R1″
-20 32 R1.1/4″
-24 40 R1.1/2″, R2″
-32 50 R2″

Material e tratamento térmico

Artigo Opção padrão Opção Premium
Material Aço de carbono de alta resistência forjado a frio (20#/35#/45#) Aço inoxidável 304 ou 316L
Tratamento térmico Carburação e têmpera, dureza do núcleo HRC 20-28 Tratamento em solução, resistência estável à corrosão
Superfície Revestimento de zinco trivalente (96 h de ensaio de névoa salina) Zinco-níquel (720 h), Dacromet (1000 h) ou passivado
Classe Thread R-series gauge-checked O mesmo, com inspeção por meio do calibrador de roscas 100%

O forjamento a frio preserva o sentido dos grãos do aço, o que aumenta a resistência à fadiga sob pulsações de pressão. Cada lote submetido a tratamento térmico é submetido a um teste de dureza e os resultados são registados, pelo que o valor de dureza indicado no MTR corresponde às peças que recebe.

Pressão de funcionamento

Artigo Classificação
Conjunto com crimpagem Governed by the hose and confirmed per hose assembly test practice; braided hose at these sizes typically carries about 10-40 MPa depending on construction and size
Threaded end (BSPT) Seals by taper thread interference per ISO 7-1 with thread sealant; the joint is rated with the assembly and sealant used
Teste de fábrica Cada peça é submetida a um teste de pressão 100% antes do envio

A classificação exata para o seu número de peça e combinação de mangueiras é confirmada na ficha técnica e pelos nossos engenheiros antes do envio.

Envelope de funcionamento de pressão-temperatura

Temperatura Retenção de pressão
-40 °C 100% de pressão nominal
-20 °C 100%
0 °C 100%
+20 °C 100%
+40 °C 100%
+60 °C 100%
+80 °C 100%
+100 °C 100%
+120 °C 100% (system derating governed by hose and elastomer seals elsewhere in the circuit, not by the fitting)

The steel body holds full rated pressure across the whole temperature window. In a crimped assembly the working pressure is governed by the weakest component, normally the hose; use the hose derating curve for the system, and the fitting will not be the limiting part.

Seleção e Encomenda

The 13011-SP BSPT male fitting series covers the crimped taper-thread segment of BSP hydraulic hose fittings, from -02 to -32, so most orders can be placed directly from the table above.

BSPT Thread Size Chart

Use this chart to identify the taper thread on your port. R threads are tapered and are identified by measuring the thread diameter and counting the threads per inch; the taper makes the diameter reduce toward the tip.

BSPT Thread (R) TPI Painel de instrumentos típico da Hose
R1/8″ 28 -03 to -04
R1/4″ 19 -04 to -06
R3/8″ 19 -04 to -08
R1/2″ 14 -06 to -12
R3/4″ 14 -08 to -16
R1″ 11 -12 to -16
R1.1/4″ 11 -20
R1.1/2″ 11 -24
R2″ 11 -24 to -32

BSPT vs BSPP Quick Check

R (BSPT) taper threads seal by interference and need PTFE tape or pipe dope. G (BSPP) parallel threads are cylindrical and seal by a cone, washer, or O-ring. The two are not interchangeable, and mixing them on one joint will leak.

Serviço de Referências Cruzadas {#by-número de peça do fabricante}

Most maintenance teams buy against a legacy part number printed on the old drawing. Send us the OEM or distributor part number you currently use, with a photo of the fitting if possible. Our engineers identify the thread, the stem profile, the hose size, and the body configuration, then confirm the exact 13011-SP equivalent before you place the order. The service covers BSPT fittings, BSP hydraulic hose fittings, and the taper-thread ends of your inventory, and interchange confirmation is free. The cross reference sheet is returned in PDF for your records.

Embalagem e Logística

Artigo Detalhe
Embalagem padrão 10 unidades por caixa (normalmente), 100 unidades por embalagem para tamanhos pequenos
Peso bruto Calculado por tamanho e confirmado na fatura pró-forma
Marcação Etiqueta na caixa com o número de peça, a quantidade e o número de lote para a inspeção à entrada
Origem Fabricado na China, fábrica HENGHUA
Documentos de exportação Fatura comercial, lista de embalagem, MTR, certificado de conformidade

Guia de Montagem e Utilização

Procedimento de crimpagem em quatro etapas

  1. Corte a mangueira em ângulo reto: utilize um cortador de mangueiras, nunca uma serra de metais nem uma rebarbadora. Uma extremidade reta e limpa é condição essencial para uma fixação uniforme da virola.
  2. Marque a profundidade de inserção: consulte a profundidade de inserção correspondente à sua série de mangueiras na ficha técnica de crimpagem e marque a linha no revestimento da mangueira.
  3. Lubrifique e insira: aplique uma camada fina de lubrificante de montagem na haste e no interior da mangueira e, em seguida, empurre o encaixe para dentro da mangueira até que a marca fique alinhada com a virola.
  4. Fazer a crimpagem e verificar: selecione a matriz de acordo com a tabela de crimpagem, efetue a crimpagem num único movimento contínuo e, em seguida, meça o diâmetro exterior da crimpagem com um paquímetro e compare com a tolerância.

Threading the BSPT End

Wrap PTFE tape clockwise around the taper thread (or apply pipe dope) before assembly. Thread the fitting into the port by hand until the thread bites, then tighten with a wrench on the S1 hexagon. The taper thread seals by interference; do not over-tighten past the manufacturer’s recommended engagement, because the wedge force grows quickly on taper threads.

Avisos relativos à instalação

  • ❌ Never interchange R (BSPT taper) threads with G (BSPP parallel) threads. They are different sealing systems and are not compatible.
  • ❌ Nunca misture acessórios e anilhas de diferentes fornecedores, mesmo que as roscas e os diâmetros das mangueiras pareçam idênticos. A geometria da haste, a dureza da anilha e os parâmetros de crimpagem diferem, e uma junta mista irá apresentar fugas ou soltar-se sob pressão.
  • ❌ Nunca efetue a crimpagem sem a ficha técnica correspondente. Uma junta com crimpagem insuficiente provoca fugas, enquanto uma junta com crimpagem excessiva danifica o reforço da mangueira.
  • ❌ Nunca volte a apertar um encaixe após uma tentativa falhada e nunca reutilize um encaixe retirado de uma mangueira.
  • ✔ Após a montagem, submeta o circuito a um ensaio de pressão a 1,5 vezes a pressão de serviço e verifique se há fugas em todas as juntas.

Personalização OEM e rastreabilidade da qualidade

Opções de personalização

  • Personalização do tamanho e da rosca: non-standard R thread and hose combinations and special stem lengths machined to your drawing.
  • Personalização do tratamento de superfícies: trivalent zinc (96 h), zinc-nickel (720 h), or Dacromet (1000 h) salt spray grades.
  • Marcação a laser: o seu logótipo, o número de peça e o código de lote marcados a laser na porca hexagonal, para garantir a rastreabilidade total no terreno.
  • Opções de materiais: Aço inoxidável 304/316L para circuitos químicos, marítimos e em contacto com alimentos, com certificados de passivação.

Sistema de Qualidade e Rastreabilidade

Cada lote segue um fluxo documentado: recebimento do aço com certificado da siderurgia → forjamento a frio → maquinagem CNC → tratamento térmico → revestimento → inspeção das roscas e dimensões segundo a norma 100% → ensaio de pressão → marcação a laser → embalagem. O número de lote indicado na caixa remete para o lote da matéria-prima, o registo do tratamento térmico e o relatório de inspeção. São fornecidos relatórios de ensaio de materiais (MTR) com cada encomenda, mediante pedido, e podem ser organizados relatórios de inspeção por entidades independentes (BV/SGS) antes do envio.

Perguntas Frequentes

Q: What is a BSPT male fitting? A: It is a crimp-on fitting for braided hose whose port end is a male R-series taper thread (ISO 7-1) and whose hose end is a serrated stem crimped onto the hose.

Q: How does a BSPT thread seal? A: The R thread is tapered, so the flanks wedge together as the fitting is tightened and the metal-to-metal interference seals the joint. Thread sealant such as PTFE tape or pipe dope is applied before assembly.

Q: What is the difference between BSPT (R) and BSPP (G) threads? A: R threads are tapered and seal by thread interference with sealant. G threads are parallel and seal by a separate element: a 60° cone, a bonded washer, or an O-ring. The two are not interchangeable.

Q: What is the difference between the 13011-SP and the 13011-SP(PO) series? A: The 13011-SP is the crimped version for braided hose, 23 sizes from R1/8″ to R2″. The 13011-SP(PO) is the push-on program version, 6 sizes from R1/8″ to R3/4″, for low-pressure lines. Send us your hose and pressure and our engineers will confirm the right version.

Q: Which hoses work with the 13011-SP series? A: The part numbers in the table are for braided hose from -02 to -32 (DN 5 to DN 50). For spiral hose, change the series number to 13012. Confirm your exact hose construction with our engineers, and the matching crimp data sheet will be supplied with the order.

P: Podem fornecer-me os dados de crimpagem para a minha mangueira? R: Sim. Cada encomenda inclui a ficha técnica de crimpagem para o modelo da sua mangueira, com a profundidade de inserção, o diâmetro exterior da crimpagem e a seleção da matriz. Envie-nos a série e a marca da sua mangueira e os nossos engenheiros irão confirmar os parâmetros de crimpagem antes do envio.

Solicitar um orçamento

Tell us the taper thread, the hose dash size, the hose construction, and the annual quantity. Whether you need stock BSP hydraulic hose fittings for distribution or a custom BSPT male fitting for an OEM program, the quoting process is the same. For replacement orders, send the legacy part number and a photo, and our engineers will confirm the interchange before quoting. Every BSPT male fitting leaves the HENGHUA factory pressure-tested, batch-coded, and backed by a written warranty. Request your quote, crimp data sheet, or drawing pack today, and we will respond within 24 hours.

Pedido de informação sobre o nosso produto

Somos um fornecedor global de acessórios e equipamentos hidráulicos, servindo uma vasta gama de setores com uma solução de abastecimento «tudo num só local». Os nossos produtos incluem mangueiras hidráulicas, acessórios, adaptadores, acoplamentos rápidos, conectores, protetores de mangueira, equipamento hidráulico e muito mais — tudo o que precisa para garantir que as suas operações decorram de forma harmoniosa e eficiente.
Indique-nos as suas necessidades através do formulário abaixo. A nossa equipa irá responder-lhe com orientação especializada e um orçamento personalizado para garantir o bom funcionamento das suas operações.