1T-SP Adapter — Straight, BSPT Male to BSPT Male

BSPT male hydraulic adapter 1T-SP specification and dimension chart

1. What a 1T-SP Adapter Does

The 1T-SP adapter is a straight hydraulic adapter that joins two BSPT taper ports, one at each end. Both Connection 1 and Connection 2 are BSPT male taper threads to ISO 7-1, the thread family where the pressure-tight joint is made on the thread flanks. The straight body adds length to the run and does not change its direction, so it is used for size conversion on a taper system or to extend a taper port out of a housing.

Both connection ends must match their mating port exactly, because that is the precondition for eliminating leakage at the conversion point. A 1T-SP adapter never bridges a taper thread and a parallel thread: a taper thread cannot seal in a parallel port, and a parallel thread cannot seal in a taper port. Where the run changes standards instead of changing size, the correct part is a conversion series such as the 1BT-SP range rather than a BSPT-to-BSPT thread adapter.

Sealing is by taper on both ends. Each end is a BSPT thread that seals on the thread flanks, so each end requires a thread sealant suited to the fluid and to the system. This differs from BSPP, which is a parallel thread to ISO 228-1 where the sealing is done by a 60° cone seat or by a bonded seal and not by the threads. The two families share a 55° thread angle, but their pitch and taper differ, so a BSPP part and a BSPT part can never be forced into each other’s port. A BSPP adapter belongs to a different family, because it seals on a seat rather than on the threads.

2. 1T-SP Specifications

2.1 Connection 1 — BSPT male taper thread

  • Norma de rosca: roscas para tubos ISO 7-1, em que as ligações estanques à pressão são realizadas nas roscas (BSPT, rosca R).
  • Género: rosca cónica macho.
  • Available thread sizes on Connection 1: R1/8″x28 to R2″x11, covering the Thread E column in the table in section 2.5.
  • Sealing method: the taper thread seals on the thread flanks. A thread sealant suited to the fluid and the system is applied before assembly.
  • Mating port standard: a taper port machined to ISO 7-1. The port must be a taper port; a parallel port to ISO 228-1 will not seal with this end.

2.2 Ligação 2 — Rosca cónica macho BSPT

  • Thread standard: ISO 7-1 taper pipe thread (BSPT, R thread), matching Connection 1.
  • Género: rosca cónica macho.
  • Available thread sizes on Connection 2: R1/8″x28 to R2″x11, covering the Thread F column in the table in section 2.5.
  • Sealing method: the taper thread seals on the thread flanks and needs a sealant, exactly as on Connection 1.
  • Size combinations: the table includes equal-size rows such as 1T-08SP and reducing rows such as 1T-12-16SP, so a larger taper port can be stepped down to a smaller taper connection.
  • Regra de reutilização: antes de reutilizar uma extremidade cónica já montada, verifique se as roscas apresentam partes achatadas ou danificadas, uma vez que a união depende do contacto entre os flancos.

2.3 Construção e materiais

The body is machined from bar stock on CNC lathes. Both taper threads are cut as separate operations, and thread gauges and dimensional checks are applied batch by batch before packing. Every batch of this BSPT adapter is checked against the drawing before packing.

  • Opções de material do corpo: aço ao carbono, aço inoxidável 304, aço inoxidável 316, estando o latão disponível como opção.
  • Opções de revestimento para o aço ao carbono: revestimento de crómio trivalente e zinco (Cr³⁺) ou revestimento de zinco-níquel. Os corpos em aço inoxidável são fornecidos sem revestimento.
  • Seal material options: NBR, FKM (Viton-type) and EPDM, matched to the fluid and the temperature of the application. On a BSPT joint the sealant carries the sealing duty, so the sealant is selected for the fluid as carefully as any elastomer in the circuit.
  • Critical surfaces: both taper threads are treated as sealing surfaces during machining, handling and packing.
  • Característica hexagonal: uma face hexagonal entre as arestas planas (S1) no corpo, com dimensões definidas de acordo com a combinação de roscas, conforme indicado na tabela.

2.4 Pressão e temperatura

A pressão é determinada pelo tamanho da rosca, pela espessura da parede do corpo, pelo método de vedação e pelo material selecionado, pelo que é confirmada por encomenda, em vez de ser publicada como um valor único para toda a gama. A pressão de serviço para estes tamanhos é confirmada por encomenda pela equipa de engenharia da HENGHUA, com base no método de vedação, no tamanho da rosca e no material selecionado.

Temperature capability follows the sealant and elastomer selection, which is a material fact rather than a rating of the adapter body:

Material da vedação Intervalo de temperatura típico de funcionamento Notas
NBR aproximadamente de -30 °C a +100 °C Óleo hidráulico mineral e serviços industriais em geral
FKM (tipo Viton) aproximadamente -20 °C a +200 °C Temperaturas mais elevadas e meios agressivos
EPDM aproximadamente de -40 °C a +120 °C Serviço relacionado com água, mistura de água e glicol e vapor

Carbon steel with zinc plating covers general hydraulic service. Choose 304 or 316 stainless steel for corrosive environments, offshore duty and wash-down areas where the taper threads are exposed.

2.5 Tabela de referências e dimensões

Column key: E is the BSPT (R) male taper thread on Connection 1. F is the BSPT (R) male taper thread on Connection 2. A and B are the two thread lengths measured from the end faces in the order shown on the specification drawing, L is the overall length and S1 is the hex across flats, in millimetres.

N.º DA PEÇA. E (BSPT male) F (BSPT macho) A (mm) B (mm) L (mm) S1 (mm)
1T-02SP R1/8″x28 R1/8″x28 10 10 26 12
1T-02-04SP R1/8″x28 R1/4″ x 19 10 14.5 30.5 14
1T-02-06SP R1/8″x28 R3/8″ x 19 10 15 31 17
1T-04SP R1/4″ x 19 R1/4″ x 19 14.5 14.5 34 14
1T-04-06SP R1/4″ x 19 R3/8″ x 19 14.5 15 35 17
1T-04-08SP R1/4″ x 19 R1/2″ x 14 15 20 43 22
1T-06SP R3/8″ x 19 R3/8″ x 19 15 15 36 17
1T-06-08SP R3/8″ x 19 R1/2″ x 14 15 20 43 22
1T-08SP R1/2″ x 14 R1/2″ x 14 20 20 46 22
1T-08-12SP R1/2″ x 14 R3/4″ x 14 20 20 48 27
1T-12SP R3/4″ x 14 R3/4″ x 14 20 20 48 27
1T-12-16SP R3/4″ x 14 R1″ x 11 20 25.5 55.5 36
1T-16SP R1″ x 11 R1″ x 11 25.5 25.5 61 36
1T-16-20SP R1″ x 11 R1,1/4″ x 11 25.5 26.5 64.5 46
1T-20SP R1,1/4″ x 11 R1,1/4″ x 11 26.5 26.5 65.5 46
1T-20-24SP R1,1/4″ x 11 R1,1/2″ x 11 26.5 26.5 67 50
1T-24SP R1,1/2″ x 11 R1,1/2″ x 11 26.5 26.5 67 50
1T-24-32SP R1,1/2″ x 11 R2″ x 11 26.5 30 71.5 65
1T-32SP R2″ x 11 R2″ x 11 30 30 75 65

3. How to Read a 1T-SP Adapter Part Number

Todos os números de referência desta série seguem o mesmo padrão, pelo que a tabela pode ser consultada sem necessidade de recorrer a um catálogo separado.

  • Prefixo 1T-SP: o Código da Família. 1 designa o grupo de conversão de homem para homem, T marks the BSPT male taper ends, and SP é o sufixo que acompanha todos os números de peça desta série, conforme indicado nas especificações. Este prefixo não contém nenhum dígito angular, uma vez que o corpo é reto.
  • First size code after the dash: the Thread E size on Connection 1.
  • Optional second size code: the Thread F size on Connection 2. When only one size code is present, the two ends are the same size, as in 1T-08SP.
  • Two-digit codes repeat the numerator of the thread size, which can be verified from any row: 02 = 1/8″, 04 = 1/4″, 06 = 3/8″, 08 = 1/2″, 12 = 3/4″, 16 = 1″, 20 = 1.1/4″, 24 = 1.1/2″, 32 = 2″.

Worked example, row 1T-12-16SP: 1T-SP is the straight BSPT-to-BSPT male family, 12 is the Thread E code for R3/4″x14, and 16 is the Thread F code for R1″x11. The row then gives A = 20 mm, B = 25.5 mm, L = 55.5 mm and S1 = 36 mm. The same size pair in an elbow body carries 9 in the prefix, which is why the straight and elbow series must not be confused when a replacement is ordered.

4. Instalação e montagem

  • Inspect before assembly. Check both taper threads for burrs, galls, flattened flanks and swarf. Because the joint seals on the flanks, surface damage on the threads leaks even when the parts are tightened correctly.
  • Apply sealant to both ends. Each BSPT end seals on the thread flanks and needs a sealant suited to the fluid and the system. Leave the first thread clean so that the sealant does not enter the circuit.
  • Check the port type before fitting. A BSPT male end can only be used in a taper port. Screwing it into a parallel port by force deforms the threads and destroys the thread form on both parts.
  • Alinhe antes de apertar. Comece por apertar ambas as extremidades à mão e verifique se as roscas encaixam livremente; em seguida, aperte até obter um contacto firme e aplique o ângulo de aperto adicional especificado para a junta. Não consta qualquer valor de ângulo de aperto nas especificações da série; por isso, siga o valor indicado nas suas instruções de montagem ou confirme-o junto do departamento de engenharia da HENGHUA.
  • Use the hex. Tighten on the S1 hex with a spanner that fits, so the load passes through the body rather than through the taper threads.
  • Contamination control. Keep the adapter capped until fitting, work with clean tools and flush the circuit afterwards where sealant debris or swarf could reach a valve.

Erros comuns na montagem e os respetivos sintomas:

Erro Sintoma
BSPT taper end forced into a BSPP parallel port Free turning for a few threads then hard binding, thread damage, joint weeps
Sealant omitted on either taper end Vazamento ao longo do fio, mesmo a baixa pressão
Excessive sealant or tape overhanging the bore Debris carried into the circuit, sticking valves, blocked orifices
Taper end reused after galling Joint seals when new, then weeps after pressure cycling
Correct BSPT ends but no size check Adapter starts but does not seat, joint stands proud of the port face

5. Aplicações e setores

Etiquetas de aplicação: sistemas hidráulicos, jato de água, petróleo e gás, equipamento industrial, maquinaria de construção, agricultura, setor marítimo, manuseamento de materiais.

Concrete scenarios where this BSPT-to-BSPT thread adapter is used:

  1. Cross-standard equipment integration. Machines assembled from components of different origin often present taper ports on cylinders, valves or pipe fittings while the rest of the circuit follows a different port standard. This series extends or steps a taper connection within the same ISO 7-1 family, and a conversion series is used where the standard itself has to change.
  2. Repair and replacement. A damaged taper nipple or an over-tightened joint is replaced with a straight adapter that restores the connection without re-cutting the pipework.
  3. Size stepping on older equipment. Legacy machinery frequently uses taper ports in sizes that are no longer standard on new valves, and the reducing rows in the table step the port down or up to the size the new component uses.
  4. Test benches and gauge lines. Straight adapters are used to bring a taper test point out of a manifold or to connect a gauge line without changing the flow direction.

6. Guia de substituição e referências cruzadas

Identify a replacement by standard, thread and sealing method, never by brand or by the marking on the installed part alone. Where the standards differ at the two ends, a cross standard adapter is required instead of this series.

Meça estes três elementos na peça que vai substituir:

  1. Both thread forms. Measure the outside diameter and count the threads per inch at each end. Both ends of this series taper, so the diameter reduces towards the nose and the thread does not hold a constant gauge along its length. A part whose ends are parallel belongs to a different family.
  2. The pitch. BSPT is a taper thread to ISO 7-1 and is specified with a pitch count such as 19 threads per inch for 1/4″ and 14 for 1/2″. Confirm the pitch against the table before ordering, because a similar diameter with a different pitch will not seal.
  3. The length. Measure L and compare it with the table, because a replacement that is longer than the original may not fit the space between the port and the first pipe bend.

Organizados por norma e não por marca:

O que tens A que se adapta Como especificá-lo
Porta cónica BSPT BSPT taper port, other size 1T-SP part number, size codes for E and F
BSPT taper port on both ends, equal size Extension of the same size 1T-SP part number with a single size code
BSPT taper port that must change standard BSPP port with a 60° seat or a flat face 1BT-SP straight, 1BT4-SP 45° or 1BT9-SP 90° series, because a BSPP adapter is required on that side
BSPT taper port that needs a right angle BSPT port, 90° 1T9-SP series
BSPT taper port that needs a female outlet BSPT female 5T-SP, 7T or 7T9-PK series

7. Encomendas, embalagem e entrega

Send the following with your inquiry so that the quotation is exact: series code and full part number (for example 1T-12-16SP), the thread size on each end, the sealant or elastomer requirement (NBR, FKM or EPDM), body material and plating option, and the annual quantity. Where the old part carries no readable marking, send the measured thread diameter and pitch at both ends instead, and HENGHUA will confirm the match.

  • Embalagem: unidades individuais em sacos selados, quantidades a granel em caixas de cartão e caixas de cartão paletizadas para carregamento em contentores. A marcação e a etiquetagem podem ser adaptadas às necessidades dos distribuidores para exposição nas prateleiras ou às necessidades dos fabricantes de equipamento original (OEM) para integração direta na linha de produção.
  • Encomendas de amostras: estão disponíveis amostras para validação antes de uma encomenda de produção. Indique os números de peça e o material da vedação que pretende que sejam avaliados.
  • Prazo de entrega: confirmado por encomenda, com base no tamanho, no material e na quantidade. Os tamanhos personalizados e a produção com base em desenhos seguem o mesmo procedimento.
  • Documentação: as cotações e as confirmações de encomenda indicam o número da peça, os dois tamanhos de rosca, o material e a opção de vedação, para que a peça entregue possa ser verificada em relação à documentação.

8. Perguntas frequentes

P1. Qual é a diferença entre o BSPP e o BSPT? Podem ser utilizados de forma intercambiável? BSPP (G thread) is a parallel thread to ISO 228-1 where the pressure-tight joint is not made on the threads: a 60° cone seat or a bonded seal does the sealing. BSPT (R thread) is a taper thread to ISO 7-1 where the joint is made on the thread flanks and needs a sealant. They must never be forced together, because the pitch and the taper differ and forcing one into the other deforms both parts. Both ends of this series are BSPT, so both mating ports must be taper ports.

P2. Qual é a diferença entre uma sede cónica de 60° e uma vedação colada, e qual devo escolher? Neither applies to this series, because both of its ends seal on the taper thread flanks with a sealant rather than on a seat. A 60° cone seat and a bonded seal both belong to BSPP practice: the cone seat seals metal-to-metal against a mating cone inside an ISO 1179 port, and the bonded seal (Dowty-type washer) seals against a flat face. If the mating port is a BSPP port with a cone seat or a flat face, use a conversion series such as 1BT-SP instead of this one.

Q3. How do I identify the correct 1T-SP size? Read the two size codes in the part number. The first code is the Thread E size and the second code is the Thread F size, both BSPT, with 02 = 1/8″, 04 = 1/4″, 06 = 3/8″, 08 = 1/2″, 12 = 3/4″, 16 = 1″, 20 = 1.1/4″, 24 = 1.1/2″ and 32 = 2″. When only one code is present, the two ends are the same size. Confirm diameter and pitch at both ends with a gauge before ordering.

P4. Que material de vedação devo escolher para o meu fluido e temperatura? NBR suits general hydraulic oil service at approximately -30°C to +100°C, FKM covers higher temperatures and aggressive media at approximately -20°C to +200°C, and EPDM covers water and water-glycol service at approximately -40°C to +120°C. On a BSPT joint the sealant does the sealing, so the sealant must also be compatible with the fluid and the temperature. Send the fluid and temperature data with your inquiry and HENGHUA will confirm the selection.

P5. Como é determinada a pressão de funcionamento deste adaptador? A pressão de serviço depende do tamanho da rosca, da espessura da parede do corpo, do método de vedação e do material selecionado, pelo que a série não é publicada com um único valor. A pressão de serviço para estes tamanhos é confirmada por encomenda pela equipa de engenharia da HENGHUA, com base no método de vedação, no tamanho da rosca e no material selecionado. Indique a pressão de serviço e o fluido na sua consulta, para que a confirmação possa ser emitida juntamente com o orçamento.

P6. Qual é a quantidade mínima de encomenda e posso obter amostras? Estão disponíveis amostras para validação antes de uma encomenda de produção, podendo ser fornecidas quantidades mais reduzidas para testes e stock de manutenção. Indique os números de peça, o material da vedação e a quantidade na sua consulta, para que os prazos de entrega das amostras e da produção possam ser confirmados em conjunto. A quantidade mínima de encomenda é confirmada para cada encomenda, de acordo com o tamanho, o material e a combinação de revestimento solicitados.

Q7. Can this adapter be used on a BSPP port with a bonded seal? No. Both ends of this series are BSPT taper threads that seal on the thread flanks, and a taper thread cannot seal in a parallel port or against a flat face. A BSPP port must be matched by a BSPP stud end, which seals on a 60° cone seat or with a bonded seal. Where the two standards meet on a machine, order a conversion series such as 1BT-SP for the straight version or its elbow equivalents.

Explorar o conteúdo completo Adaptadores hidráulicos uma gama para toda a família, ou contacte-nos para solicitar um orçamento, relatórios de ensaios de fábrica e amostras.

Pedido de informação sobre o nosso produto

Somos um fornecedor global de acessórios e equipamentos hidráulicos, servindo uma vasta gama de setores com uma solução de abastecimento «tudo num só local». Os nossos produtos incluem mangueiras hidráulicas, acessórios, adaptadores, acoplamentos rápidos, conectores, protetores de mangueira, equipamento hidráulico e muito mais — tudo o que precisa para garantir que as suas operações decorram de forma harmoniosa e eficiente.
Indique-nos as suas necessidades através do formulário abaixo. A nossa equipa irá responder-lhe com orientação especializada e um orçamento personalizado para garantir o bom funcionamento das suas operações.