BSP Male Double Use Fitting: 12611A Series

bsp male double use 60 degree seat fitting 12611a series spec

Why This BSP Male Double Use Fitting Passes the Compliance Gate

A BSP male double use fitting terminates a braided hydraulic hose in a male G-threaded stud that can seal two ways: by its internal 60° cone seat against a female swivel 60° cone end, or by a bonded washer on its flat hexagon end face against a flat-faced BSPP port. The 12611A series from HENGHUA covers 20 part numbers from -02 to -32 with G-series parallel threads from G1/8″ to G2″. Every unit is cold-forged from carbon steel, heat-treated, plated, and 100% pressure tested before shipment. For OEM buyers this fitting is a compliance gate; for maintenance teams it is the dual-seal male termination that fits whichever seat style the machine carries, which cuts the number of part numbers in a service kit.

  • Double use sealing: the same fitting seals two ways. The internal (concave) 60° cone seat at the thread tip mates metal-to-metal with a female swivel 60° cone end; the flat hexagon end face at the base of the threads seals with a bonded washer (Dowty-type seal) against a flat-faced port. One part number covers both circuit styles.
  • BSPP G thread: the thread is parallel (G series, ISO 228-1) and only holds the connection in both sealing modes; the cone seat or the bonded washer does the sealing. G threads must never be interchanged with BSPT taper threads, which seal by thread interference.
  • Wrenching hexagon: the drawing shows one hexagon, S1, at the centre of the fitting; its end face doubles as the bonded-seal shoulder, and its across-flats size matches the standard hex for the G thread.
  • Braided hose executions: the part numbers in the table are for braided hose from -02 to -32; for spiral hose, change the series number to 12612A per the factory sheet.
  • Verificação do portão OEM: full dimensional and material conformance with G thread form per ISO 228-1, with material test reports (MTR) available for every batch.

Principais vantagens

  1. One fitting, two seal systems: stock one part number and it seals on a 60° cone seat joint or on a flat-faced port with a bonded washer, whichever the machine uses.
  2. Fewer part numbers in service stock: because the same male end serves both seat styles, maintenance and OEM kits hold fewer line items.
  3. Metal cone option has no soft element: when used as a 60° cone seat fitting, the joint seals metal-to-metal without a washer or O-ring.
  4. Bonded seal option is field-serviceable: when used as a flat-face fitting, the seal element is a replaceable bonded washer.
  5. Opções de ensaio de névoa salina de 96 a 1000 h: zinco trivalente (96 h), zinco-níquel (720 h) ou Dacromet (1000 h), de acordo com o seu ambiente.

Especificações Técnicas

What Is This BSP Male Double Use Fitting?

This BSP male double use fitting terminates a braided hose in a male stud end that supports both major BSPP sealing systems. The port end is a male parallel G thread (G series, thread form per ISO 228-1). At the tip of the thread there is a machined internal (concave) 60° cone seat; at the base of the thread, the hexagon end face is machined flat. This gives the fitter two legitimate ways to make the joint:

  1. Cone seat mode: a female swivel fitting with a 60° cone is screwed onto the thread, and the cone is drawn into the internal cone seat for a metal-to-metal seal. Use this mode when the mating side is a female swivel 60° cone end, as on our 22611-series fittings.
  2. Bonded seal mode: a bonded washer (Dowty-type seal) is fitted on the flat hexagon end face, and the fitting is screwed into a flat-faced BSPP port or female fitting; the washer is compressed between the two flat faces to seal. Use this mode when the mating side is a flat-faced BSPP port.

Both modes use the same parallel G thread, which never seals by interference. This is why the fitting must never be paired with a BSPT taper thread, which seals by thread interference instead. Choose the sealing mode by the mating component, and choose the seal element accordingly: the cone seat needs a clean matching cone, and the bonded seal mode needs the correct washer compound for the fluid and temperature.

The 12611A is the double use member of the male BSP hose fitting family, complementing the single-purpose male cone seat series (12611) and the flat seat system in one part. The single hexagon S1 sits at the centre of the fitting, its end face serving as the bonded-seal shoulder; its across-flats size matches the standard hex for the G thread, so service tools are shared with the rest of the BSP range. The series covers 20 sizes from -02 to -32; the part numbers in the table are for braided hose, and for spiral hose the series number changes to 12612A. The serrated hose tail is engineered for a crimped termination; confirm your exact hose construction with our engineers and the matching crimp data sheet is supplied with the order.

Dados dimensionais e roscas

Símbolo Descrição
E BSPP male thread (G series, ISO 228-1), G1/8″ to G2″
A Overall length of the fitting, from the thread tip to the end of the hose stem
C Length of the threaded portion
S1 Hex across flats at the centre of the fitting; the end face doubles as the bonded-seal shoulder
Traço Hose inside diameter in 1/16″ increments (-02 to -32)
DN Hose inside diameter in millimetres (5 to 50)

Full dimension drawings with A, C, and S1 callouts are supplied as PDF and CAD (STEP/DWG) files. Because this is a crimp fitting, the two process-critical parameters are the hose insert depth and the crimp outside diameter; both are hose-series specific and are listed in the crimp data sheet that accompanies every order.

Tabela completa de dimensões (matriz de referências) {#by-thread-size}

Read the table with your BSPP thread (E) and your hose size (dash). The part number is the order code; copy it directly into your inquiry or purchase order. The pattern is 12611A-[thread dash]-[hose dash]: for example, 12611A-12-12 has a G3/4″ thread and suits a -12 (20 mm) braided hose.

N.º da peça. Rosca E (BSPP) Diâmetro interno da mangueira DN (mm) Traço A (mm) C (mm) S1 (mm)
12611A-02-03 G1/8″x28 5 03 22 10 14
12611A-04-04 G1/4″x19 6 04 24.5 12 19
12611A-04-05 G1/4″x19 8 05 24.5 12 19
12611A-06-05 G3/8″ x 19 8 05 26 13.5 22
12611A-06-06 G3/8″ x 19 10 06 28 13.5 22
12611A-06-08 G3/8″ x 19 12 08 28.5 13.5 22
12611A-08-06 G1/2″x14 10 06 33 16 27
12611A-08-08 G1/2″x14 12 08 33.5 16 27
12611A-08-10 G1/2″x14 16 10 32 16 27
12611A-10-08 G5/8″ x 14 12 08 35 17.5 30
12611A-10-10 G5/8″ x 14 16 10 36 17.5 30
12611A-12-08 G3/4″ x 14 12 08 36.5 18.5 32
12611A-12-10 G3/4″ x 14 16 10 37.5 18.5 32
12611A-12-12 G3/4″ x 14 20 12 37.5 18.5 32
12611A-16-12 G1″ x 11 20 12 42.5 20.5 41
12611A-16-16 G1″ x 11 25 16 43.5 20.5 41
12611A-20-16 G1,1/4″ x 11 25 16 45.5 20.5 50
12611A-20-20 G1,1/4″ x 11 32 20 46.5 20.5 50
12611A-24-24 G1,1/2″ x 11 40 24 49 23 55
12611A-32-32 G2″ x 11 50 32 54.5 25.5 70

The part numbers shown are for the braided-hose version. For spiral hose, change the series number to 12612A, whose stem is longer for the extra reinforcement layers.

Selecionar por tamanho do traço da mangueira {#by-hose-size}

Match your hose bore first, then read the thread sizes available for that bore:

Hose Dash Diâmetro interno da mangueira (mm) Available BSPP Threads in the 12611A Series
-03 5 G1/8″
-04 6 G1/4″
-05 8 G1/4″, G3/8″
-06 10 G3/8″, G1/2″
-08 12 G3/8″, G1/2″, G5/8″, G3/4″
-10 16 G1/2″, G5/8″, G3/4″
-12 20 G3/4″, G1″
-16 25 G1″, G1.1/4″
-20 32 G1.1/4″
-24 40 G1.1/2″
-32 50 G2″

Material e tratamento térmico

Artigo Opção padrão Opção Premium
Material Aço de carbono de alta resistência forjado a frio (20#/35#/45#) Aço inoxidável 304 ou 316L
Tratamento térmico Carburação e têmpera, dureza do núcleo HRC 20-28 Tratamento em solução, resistência estável à corrosão
Superfície Revestimento de zinco trivalente (96 h de ensaio de névoa salina) Zinco-níquel (720 h), Dacromet (1000 h) ou passivado
Classe Thread Série G com verificação por medidor O mesmo, com inspeção por meio do calibrador de roscas 100%

O forjamento a frio preserva o sentido dos grãos do aço, o que aumenta a resistência à fadiga sob pulsações de pressão. Cada lote submetido a tratamento térmico é submetido a um teste de dureza e os resultados são registados, pelo que o valor de dureza indicado no MTR corresponde às peças que recebe.

Pressão de funcionamento

Artigo Classificação
Cone seat mode Rated for the pressure class of the 60° cone connection geometry; the rating for your part number is confirmed on the datasheet
Bonded seal mode Rated for the connection class with the bonded washer, which sets the temperature and fluid limits of the joint
Conjunto com crimpagem Governed by the hose and confirmed per hose assembly test practice; braided hose at these sizes typically carries about 10-40 MPa depending on construction and size
Teste de fábrica Cada peça é submetida a um teste de pressão 100% antes do envio

The exact rating for your part number, sealing mode, and hose combination is confirmed on the datasheet and by our engineers before shipment.

Envelope de funcionamento de pressão-temperatura

Temperatura Retenção de pressão
-40 °C 100% of rated pressure (bonded seal compound dependent at the low end)
-20 °C 100%
0 °C 100%
+20 °C 100%
+40 °C 100%
+60 °C 100%
+80 °C 100%
+100 °C 100% (bonded seal compound dependent)
+120 °C In cone seat mode the steel joint holds; in bonded seal mode the washer compound sets the limit

The steel body holds its strength across the full temperature window. In cone seat mode there is no elastomer in the sealing path and the fitting is not the temperature-limiting part. In bonded seal mode the washer compound sets the practical limit; confirm the compound for your fluid and temperature range with our engineers.

Seleção e Encomenda

The 12611A BSP male double use fitting series covers the dual-seal segment of BSP hydraulic hose fittings, from -02 to -32, so most orders can be placed directly from the table above.

Tabela de tamanhos de roscas BSPP

Utilize esta tabela para identificar o tipo de rosca da sua porta. As roscas BSPP G são paralelas; identificam-se medindo o diâmetro exterior da rosca e contando o número de roscas por polegada.

Rosca BSPP (G) TPI Traço de linha Painel de instrumentos típico da Hose
G1/8″ 28 -02 -03
G1/4″ 19 -04 -04 to -05
G3/8″ 19 -06 -05 to -08
G1/2″ 14 -08 -06 to -10
G5/8″ 14 -10 -08 to -10
G3/4″ 14 -12 -08 to -12
G1″ 11 -16 -12 to -16
G1.1/4″ 11 -20 -16 to -20
G1.1/2″ 11 -24 -24
G2″ 11 -32 -32

Serviço de Referências Cruzadas {#by-número de peça do fabricante}

Most maintenance teams buy against a legacy part number printed on the old drawing. Send us the OEM or distributor part number you currently use, with a photo of the fitting if possible. Our engineers identify the thread, the dual seal geometry, the hose size, and the body configuration, then confirm the exact 12611A equivalent before you place the order. The service covers double use fittings, 60° cone fittings, BSP hydraulic hose fittings, and the male stud ends of your inventory, and interchange confirmation is free. The cross reference sheet is returned in PDF for your records.

Embalagem e Logística

Artigo Detalhe
Embalagem padrão 10 unidades por caixa (normalmente), 100 unidades por embalagem para tamanhos pequenos
Peso bruto Calculado por tamanho e confirmado na fatura pró-forma
Marcação Etiqueta na caixa com o número de peça, a quantidade e o número de lote para a inspeção à entrada
Origem Fabricado na China, fábrica HENGHUA
Documentos de exportação Fatura comercial, lista de embalagem, MTR, certificado de conformidade

Guia de Montagem e Utilização

Procedimento de crimpagem em quatro etapas

  1. Corte a mangueira em ângulo reto: utilize um cortador de mangueiras, nunca uma serra de metais nem uma rebarbadora. Uma extremidade reta e limpa é condição essencial para uma fixação uniforme da virola.
  2. Marque a profundidade de inserção: consulte a profundidade de inserção correspondente à sua série de mangueiras na ficha técnica de crimpagem e marque a linha no revestimento da mangueira.
  3. Lubrifique e insira: aplique uma camada fina de lubrificante de montagem na haste e no interior da mangueira e, em seguida, empurre o encaixe para dentro da mangueira até que a marca fique alinhada com a virola.
  4. Fazer a crimpagem e verificar: selecione a matriz de acordo com a tabela de crimpagem, efetue a crimpagem num único movimento contínuo e, em seguida, meça o diâmetro exterior da crimpagem com um paquímetro e compare com a tolerância.

Connecting in Cone Seat Mode

On the BSP male double use fitting used as a cone seat end, clean the internal cone seat and the cone of the mating female swivel fitting with a lint-free cloth. Hold the S1 hexagon with a wrench and thread the female nut onto the male G thread by hand until the cone touches the seat, then tighten to the torque listed for the thread size. The 60° cone contact does the sealing, so no sealant is applied to the cone faces.

Connecting in Bonded Seal Mode

Used as a flat-face end, fit a bonded washer (Dowty-type seal) of the correct size and compound on the flat hexagon end face, seating it evenly. Clean the flat face of the BSPP port with a lint-free cloth. Thread the fitting into the port and tighten to the torque listed for the thread size; the washer compresses between the two flat faces to seal. Replace the washer at every disassembly, and never reuse a hardened or cut washer.

Avisos relativos à instalação

  • ❌ Nunca misture acessórios e anilhas de diferentes fornecedores, mesmo que as roscas e os diâmetros das mangueiras pareçam idênticos. A geometria da haste, a dureza da anilha e os parâmetros de crimpagem diferem, e uma junta mista irá apresentar fugas ou soltar-se sob pressão.
  • ❌ Never confuse the two sealing modes: cone seat mode needs a clean mating cone and no sealant; bonded seal mode needs a washer of the right size and compound on the flat end face. Do not use a bonded washer between two cone faces, and do not rely on a bare flat face without a washer.
  • ❌ Never confuse G (BSPP parallel) threads with R (BSPT taper) threads. A G thread seals by cone contact or by washer; a taper thread seals by thread interference and needs sealant. The two are not interchangeable.
  • ❌ Nunca efetue a crimpagem sem a ficha técnica correspondente. Uma junta com crimpagem insuficiente provoca fugas, enquanto uma junta com crimpagem excessiva danifica o reforço da mangueira.
  • ❌ Nunca volte a apertar um encaixe após uma tentativa falhada e nunca reutilize um encaixe retirado de uma mangueira.
  • ✔ Após a montagem, submeta o circuito a um ensaio de pressão a 1,5 vezes a pressão de serviço e verifique se há fugas em todas as juntas.

Personalização OEM e rastreabilidade da qualidade

Opções de personalização

  • Bonded washer supply: washers supplied with the fittings, in the compound matched to your fluid and temperature.
  • Personalização do tamanho e da rosca: combinações não normalizadas de roscas G e mangueiras, bem como comprimentos especiais de haste, usinados de acordo com o seu desenho.
  • Personalização do tratamento de superfícies: zinco trivalente (96 h), zinco-níquel (720 h) ou Dacromet (1000 h) — classes de resistência ao teste de névoa salina, selecionadas de acordo com o seu ambiente e as especificações de corrosão.
  • Marcação a laser: o seu logótipo, o número de peça e o código de lote marcados a laser na porca hexagonal, para garantir a rastreabilidade total no terreno.
  • Opções de materiais: Aço inoxidável 304/316L para circuitos químicos, marítimos e em contacto com alimentos, com certificados de passivação.

Sistema de Qualidade e Rastreabilidade

Cada lote segue um fluxo documentado: recebimento do aço com certificado da siderurgia → forjamento a frio → maquinagem CNC → tratamento térmico → revestimento → inspeção das roscas e dimensões segundo a norma 100% → ensaio de pressão → marcação a laser → embalagem. O número de lote indicado na caixa remete para o lote da matéria-prima, o registo do tratamento térmico e o relatório de inspeção. São fornecidos relatórios de ensaio de materiais (MTR) com cada encomenda, mediante pedido, e podem ser organizados relatórios de inspeção por entidades independentes (BV/SGS) antes do envio.

Perguntas Frequentes

Q: What is a BSP male double use fitting? A: It is a crimp-on fitting for braided hose whose port end is a male parallel G thread (ISO 228-1) that can seal two ways: by an internal 60° cone seat at the thread tip against a female swivel 60° cone end, or by a bonded washer on the flat hexagon end face against a flat-faced BSPP port.

Q: Why is it called double use? A: The same part number covers both major BSPP seat styles. One end of the thread carries a 60° internal cone seat, and the hexagon shoulder behind the thread carries a flat bonded-seal face. Depending on the mating component, you use one or the other sealing method.

Q: Which sealing mode should I use? A: Use cone seat mode when the mating side is a female swivel fitting with a 60° cone (for example our 22611-series fittings). Use bonded seal mode when the mating side is a flat-faced BSPP port or female fitting, fitting a bonded washer of the correct size and compound.

Q: What is the difference between the 12611A and the single-purpose 12611 male cone seat series? A: The 12611 seals only by its 60° internal cone seat. The 12611A adds the flat hexagon end face with bonded washer sealing, so one part number serves both cone seat and flat seat circuits.

Q: Which hoses work with the 12611A series? A: The part numbers in the table are for braided hose from -02 to -32 (DN 5 to DN 50). For spiral hose, change the series number to 12612A. Confirm your exact hose construction with our engineers, and the matching crimp data sheet will be supplied with the order.

P: Podem fornecer-me os dados de crimpagem para a minha mangueira? R: Sim. Cada encomenda inclui a ficha técnica de crimpagem para o modelo da sua mangueira, com a profundidade de inserção, o diâmetro exterior da crimpagem e a seleção da matriz. Envie-nos a série e a marca da sua mangueira e os nossos engenheiros irão confirmar os parâmetros de crimpagem antes do envio.

Solicitar um orçamento

Tell us the BSPP thread, the hose dash size, the hose construction, the sealing mode you use, and the annual quantity. Whether you need stock BSP hydraulic hose fittings for distribution or a custom double use fitting for an OEM program, the quoting process is the same. For replacement orders, send the legacy part number and a photo, and our engineers will confirm the interchange before quoting. Every BSP male double use fitting leaves the HENGHUA factory pressure-tested, batch-coded, and backed by a written warranty. Request your quote, crimp data sheet, or drawing pack today, and we will respond within 24 hours.

Pedido de informação sobre o nosso produto

Somos um fornecedor global de acessórios e equipamentos hidráulicos, servindo uma vasta gama de setores com uma solução de abastecimento «tudo num só local». Os nossos produtos incluem mangueiras hidráulicas, acessórios, adaptadores, acoplamentos rápidos, conectores, protetores de mangueira, equipamento hidráulico e muito mais — tudo o que precisa para garantir que as suas operações decorram de forma harmoniosa e eficiente.
Indique-nos as suas necessidades através do formulário abaixo. A nossa equipa irá responder-lhe com orientação especializada e um orçamento personalizado para garantir o bom funcionamento das suas operações.