BSP Male 60° Cone Seat Fitting: 12613 Series

bsp male 60 degree cone seat fitting 12613 spec

Why This BSP Male 60° Cone Seat Fitting Passes the Compliance Gate

A BSP male 60° cone seat fitting terminates a braided hydraulic hose in a male G-threaded stud whose tip carries an internal 60° cone seat. It is the male half of the BSPP 60° cone connection: a female swivel fitting with a 60° cone (as on our 22613-W series) is screwed onto the male thread, and its cone is drawn into this fitting’s cone seat to form a metal-to-metal seal. The 12613 series from HENGHUA is the large-size heavy-duty execution of the male cone seat line, covering five part numbers from -12 to -32 with G-series parallel threads from G3/4″ to G2″. Every unit is cold-forged from carbon steel, heat-treated, plated, and 100% pressure tested before shipment. For OEM buyers this fitting is a compliance gate; for maintenance teams it is the male cone seat termination that carries the big lines on mobile and industrial machines.

  • Internal 60° cone seat: the tip of the male thread carries a machined internal (concave) 60° cone seat. When a female swivel 60° cone end is tightened onto the thread, the mating cone seats into this recess and the two metal faces seal without an O-ring.
  • BSPP G thread: the thread is parallel (G series, ISO 228-1) and only holds the connection; the cone seat does the sealing. G threads must never be interchanged with BSPT taper threads, which seal by thread interference.
  • Wrenching hexagon: the drawing shows one hexagon, S1, between the threaded section and the hose tail, so the fitting can be held firmly while the female nut is torqued against it.
  • Large-bore coverage: -12 to -32 with hose bores DN 20 to DN 50 covers the big lines on excavators, loaders, drilling rigs, presses, and plant hydraulics, and pairs size-for-size with the 22613-W female heavy line.
  • Verificação do portão OEM: full dimensional and material conformance with G thread form per ISO 228-1, with material test reports (MTR) available for every batch.

Principais vantagens

  1. The cone seat side of the large-bore joint: if your big lines mate female swivel 60° cone ends, this fitting provides the matching male thread and cone seat in the heavy size range.
  2. Metal-to-metal cone seal: the cone-to-seat contact seals without washers or O-rings in the standard version, removing a soft element from the pressure path.
  3. Five part numbers cover the big lines: G3/4″ to G2″ with DN 20 to DN 50 hose bores, matched to the 22613-W female executions.
  4. Single hexagon for installation: the S1 hex sits between thread and tail, giving a solid wrenching point when you tighten the mating female nut.
  5. Opções de ensaio de névoa salina de 96 a 1000 h: zinco trivalente (96 h), zinco-níquel (720 h) ou Dacromet (1000 h), de acordo com o seu ambiente.

Especificações Técnicas

What Is This BSP Male 60° Cone Seat Fitting?

This BSP male 60° cone seat fitting terminates a braided hose in the male stud side of the BSP 60° cone connection. The port end is a male parallel G thread (G series, thread form per ISO 228-1); at the tip of the thread, the fitting carries a machined internal (concave) 60° cone seat. The other end is a serrated hose tail that is crimped onto the hose. When a female swivel fitting with a 60° cone is tightened onto the male thread, the mating cone is drawn into this fitting’s internal cone seat and the two metal faces meet in a metal-to-metal seal. The G thread is parallel and does not seal by interference; it only pulls the cone into the seat. This is why a 60° cone seat must never be paired with a BSPT taper thread, which seals by thread interference instead.

The 12613 is the large-size member of the male cone seat family. The base 12611 series covers the full spread from G1/8″ to G2″, while the 12613 line concentrates on the heavy-duty executions from G3/4″ to G2″ with its own stem geometry and part numbers. The 12613 male line pairs size-for-size with the 22613-W female heavy line in the same catalog: when you build a big hose assembly with a 22613-W female end, the matching 12613 male end carries the stud side of the next joint. Buying both halves from the same catalog means the cone geometry, thread sizes, and seal faces are matched by design.

Use this male fitting when the mating component is a female swivel 60° cone end. The single hexagon S1 sits between the threaded section and the hose tail, giving a firm wrenching point while the female nut is torqued. The serrated hose tail is engineered for a crimped termination; confirm your exact hose construction with our engineers and the matching crimp data sheet is supplied with the order.

Dados dimensionais e roscas

Símbolo Descrição
E BSPP male thread (G series, ISO 228-1), G3/4″ to G2″
A Overall length of the fitting, from the thread tip to the shoulder at the base of the hexagon
C Length of the threaded portion
S1 Hex across flats, between the threaded section and the hose tail
Traço Hose inside diameter in 1/16″ increments (-12 to -32)
DN Hose inside diameter in millimetres (20 to 50)

Full dimension drawings with A, C, and S1 callouts are supplied as PDF and CAD (STEP/DWG) files. Because this is a crimp fitting, the two process-critical parameters are the hose insert depth and the crimp outside diameter; both are hose-series specific and are listed in the crimp data sheet that accompanies every order.

Tabela completa de dimensões (matriz de referências) {#by-thread-size}

Read the table with your BSPP thread (E) and your hose size (dash). The part number is the order code; copy it directly into your inquiry or purchase order. The pattern is 12613-[thread dash]-[hose dash]: for example, 12613-16-16 has a G1″ thread and suits a -16 (25 mm) hose.

N.º da peça. Rosca E (BSPP) Diâmetro interno da mangueira DN (mm) Traço A (mm) C (mm) S1 (mm)
12613-12-12 G3/4″ x 14 20 12 37.5 18.5 30
12613-16-16 G1″ x 11 25 16 41 20.5 36
12613-20-20 G1,1/4″ x 11 32 20 45.3 20.5 46
12613-24-24 G1,1/2″ x 11 40 24 49.7 23 50
12613-32-32 G2″ x 11 50 32 52 25.5 60

The dimensions shown are the standard executions of the 12613 series as drawn on the factory specification sheet. If your hose construction needs a different stem profile, a custom BSP male 60° cone seat fitting is machined on request.

Selecionar por tamanho do traço da mangueira {#by-hose-size}

Verifique primeiro o diâmetro interior da mangueira e, em seguida, confirme a rosca correspondente a esse diâmetro:

Hose Dash Diâmetro interno da mangueira (mm) N.º de referência
-12 20 12613-12-12 (G3/4″)
-16 25 12613-16-16 (G1″)
-20 32 12613-20-20 (G1.1/4″)
-24 40 12613-24-24 (G1.1/2″)
-32 50 12613-32-32 (G2″)

Material e tratamento térmico

Artigo Opção padrão Opção Premium
Material Aço de carbono de alta resistência forjado a frio (20#/35#/45#) Aço inoxidável 304 ou 316L
Tratamento térmico Carburação e têmpera, dureza do núcleo HRC 20-28 Tratamento em solução, resistência estável à corrosão
Superfície Revestimento de zinco trivalente (96 h de ensaio de névoa salina) Zinco-níquel (720 h), Dacromet (1000 h) ou passivado
Classe Thread Série G com verificação por medidor O mesmo, com inspeção por meio do calibrador de roscas 100%

O forjamento a frio preserva o sentido dos grãos do aço, o que aumenta a resistência à fadiga sob pulsações de pressão. Cada lote submetido a tratamento térmico é submetido a um teste de dureza e os resultados são registados, pelo que o valor de dureza indicado no MTR corresponde às peças que recebe.

Pressão de funcionamento

Artigo Classificação
60° cone seat end (BSPP male) Rated for the pressure class of the 60° cone connection geometry; the rating for your part number is confirmed on the datasheet
Conjunto com crimpagem Governed by the hose and confirmed per hose assembly test practice; large-bore hose at these sizes typically carries about 10-30 MPa depending on construction and size
Teste de fábrica Cada peça é submetida a um teste de pressão 100% antes do envio

A classificação exata para o seu número de peça e combinação de mangueiras é confirmada na ficha técnica e pelos nossos engenheiros antes do envio.

Envelope de funcionamento de pressão-temperatura

Temperatura Retenção de pressão
-40 °C 100% de pressão nominal
-20 °C 100%
0 °C 100%
+20 °C 100%
+40 °C 100%
+60 °C 100%
+80 °C 100%
+100 °C 100%
+120 °C 100% (system derating governed by hose and elastomer seals elsewhere in the circuit, not by the fitting)

The steel cone seat and body hold full rated pressure across the whole temperature window. In a crimped assembly the working pressure is governed by the weakest component, normally the hose; use the hose derating curve for the system, and the fitting will not be the limiting part.

Seleção e Encomenda

The 12613 BSP male 60° cone seat fitting series covers the large-bore male segment of BSP hydraulic hose fittings for straight terminations, so most orders can be placed directly from the table above.

Tabela de tamanhos de roscas BSPP

Utilize esta tabela para identificar o tipo de rosca da sua porta. As roscas BSPP G são paralelas; identificam-se medindo o diâmetro exterior da rosca e contando o número de roscas por polegada.

Rosca BSPP (G) TPI Traço de linha Painel de instrumentos típico da Hose
G3/4″ 14 -12 -12
G1″ 11 -16 -16
G1.1/4″ 11 -20 -20
G1.1/2″ 11 -24 -24
G2″ 11 -32 -32

Serviço de Referências Cruzadas {#by-número de peça do fabricante}

Most maintenance teams buy against a legacy part number printed on the old drawing. Send us the OEM or distributor part number you currently use, with a photo of the fitting if possible. Our engineers identify the thread, the cone seat geometry, the hose size, and the body configuration, then confirm the exact 12613 equivalent before you place the order. The service covers 60° cone fittings, BSP hydraulic hose fittings, and the male stud ends of your inventory, and interchange confirmation is free. The cross reference sheet is returned in PDF for your records.

Embalagem e Logística

Artigo Detalhe
Embalagem padrão 10 pcs per box (typical), fewer per carton for the large sizes
Peso bruto Calculado por tamanho e confirmado na fatura pró-forma
Marcação Etiqueta na caixa com o número de peça, a quantidade e o número de lote para a inspeção à entrada
Origem Fabricado na China, fábrica HENGHUA
Documentos de exportação Fatura comercial, lista de embalagem, MTR, certificado de conformidade

Guia de Montagem e Utilização

Procedimento de crimpagem em quatro etapas

  1. Corte a mangueira em ângulo reto: utilize um cortador de mangueiras, nunca uma serra de metais nem uma rebarbadora. Uma extremidade reta e limpa é condição essencial para uma fixação uniforme da virola.
  2. Marque a profundidade de inserção: consulte a profundidade de inserção correspondente à sua série de mangueiras na ficha técnica de crimpagem e marque a linha no revestimento da mangueira.
  3. Lubrifique e insira: aplique uma camada fina de lubrificante de montagem na haste e no interior da mangueira e, em seguida, empurre o encaixe para dentro da mangueira até que a marca fique alinhada com a virola.
  4. Fazer a crimpagem e verificar: selecione a matriz de acordo com a tabela de crimpagem, efetue a crimpagem num único movimento contínuo e, em seguida, meça o diâmetro exterior da crimpagem com um paquímetro e compare com a tolerância.

Connecting the 60° Cone Seat End

On the BSP male 60° cone seat fitting, clean the internal cone seat and the cone of the mating female swivel fitting with a lint-free cloth. Hold the S1 hexagon with a wrench and thread the female nut onto the male G thread by hand until the cone touches the seat, then tighten to the torque listed for the thread size. The 60° cone contact does the sealing, so no sealant is applied to the cone faces. If your circuit uses the O-ring variant of the 60° cone family, fit the correct O-ring before assembly; do not mix the O-ring and plain cone versions.

Avisos relativos à instalação

  • ❌ Nunca misture acessórios e anilhas de diferentes fornecedores, mesmo que as roscas e os diâmetros das mangueiras pareçam idênticos. A geometria da haste, a dureza da anilha e os parâmetros de crimpagem diferem, e uma junta mista irá apresentar fugas ou soltar-se sob pressão.
  • ❌ Never confuse G (BSPP parallel) threads with R (BSPT taper) threads. A G thread with a 60° cone seat seals by cone contact; a taper thread seals by thread interference and needs sealant. The two are not interchangeable.
  • ❌ Never match a cone seat to a scratched or pitted mating cone. The metal-to-metal seal needs an undamaged sealing surface on both sides.
  • ❌ Nunca efetue a crimpagem sem a ficha técnica correspondente. Uma junta com crimpagem insuficiente provoca fugas, enquanto uma junta com crimpagem excessiva danifica o reforço da mangueira.
  • ❌ Nunca volte a apertar um encaixe após uma tentativa falhada e nunca reutilize um encaixe retirado de uma mangueira.
  • ✔ Após a montagem, submeta o circuito a um ensaio de pressão a 1,5 vezes a pressão de serviço e verifique se há fugas em todas as juntas.

Personalização OEM e rastreabilidade da qualidade

Opções de personalização

  • Personalização do tamanho e da rosca: combinações não normalizadas de roscas G e mangueiras, bem como comprimentos especiais de haste, usinados de acordo com o seu desenho.
  • Personalização do tratamento de superfícies: zinco trivalente (96 h), zinco-níquel (720 h) ou Dacromet (1000 h) — classes de resistência ao teste de névoa salina, selecionadas de acordo com o seu ambiente e as especificações de corrosão.
  • Marcação a laser: o seu logótipo, o número de peça e o código de lote marcados a laser na porca hexagonal, para garantir a rastreabilidade total no terreno.
  • Opções de materiais: Aço inoxidável 304/316L para circuitos químicos, marítimos e em contacto com alimentos, com certificados de passivação.

Sistema de Qualidade e Rastreabilidade

Cada lote segue um fluxo documentado: recebimento do aço com certificado da siderurgia → forjamento a frio → maquinagem CNC → tratamento térmico → revestimento → inspeção das roscas e dimensões segundo a norma 100% → ensaio de pressão → marcação a laser → embalagem. O número de lote indicado na caixa remete para o lote da matéria-prima, o registo do tratamento térmico e o relatório de inspeção. São fornecidos relatórios de ensaio de materiais (MTR) com cada encomenda, mediante pedido, e podem ser organizados relatórios de inspeção por entidades independentes (BV/SGS) antes do envio.

Perguntas Frequentes

Q: What is a BSP male 60° cone seat fitting? A: It is a crimp-on fitting for hose whose port end is a male parallel G thread (ISO 228-1); the tip of the thread carries an internal 60° cone seat that receives the cone of a female swivel 60° cone end.

Q: How does the connection seal? A: A female swivel fitting with a 60° cone is screwed onto the male thread, and the cone is drawn into the internal cone seat. The two metal faces meet in a metal-to-metal seal; the G thread only holds the connection.

Q: What is the difference between the 12613 and the 12611 series? A: Both are male BSPP 60° cone seat fittings with the same thread and cone geometry. The 12611 series spans G1/8″ to G2″; the 12613 is the heavy-duty execution line concentrated on the large sizes G3/4″ to G2″ with its own stem geometry and part numbers.

Q: How does the 12613 pair with the 22613-W female series? A: The 22613-W female swivel fittings carry the nut with the internal G thread and the convex cone. The 12613 male fittings carry the external G thread and the concave cone seat that receives it. The two are the matching halves of the same large-size heavy joint.

Q: Which hoses work with the 12613 series? A: The part numbers in the table suit braided hose from -12 to -32 (DN 20 to DN 50). Confirm your exact hose construction with our engineers, and the matching crimp data sheet will be supplied with the order.

P: Podem fornecer-me os dados de crimpagem para a minha mangueira? R: Sim. Cada encomenda inclui a ficha técnica de crimpagem para o modelo da sua mangueira, com a profundidade de inserção, o diâmetro exterior da crimpagem e a seleção da matriz. Envie-nos a série e a marca da sua mangueira e os nossos engenheiros irão confirmar os parâmetros de crimpagem antes do envio.

Solicitar um orçamento

Tell us the BSPP thread, the hose dash size, the hose construction, and the annual quantity. Whether you need stock BSP hydraulic hose fittings for distribution or a custom 60° cone fitting for an OEM program, the quoting process is the same. For replacement orders, send the legacy part number and a photo, and our engineers will confirm the interchange before quoting. Every BSP male 60° cone seat fitting leaves the HENGHUA factory pressure-tested, batch-coded, and backed by a written warranty. Request your quote, crimp data sheet, or drawing pack today, and we will respond within 24 hours.

Pedido de informação sobre o nosso produto

Somos um fornecedor global de acessórios e equipamentos hidráulicos, servindo uma vasta gama de setores com uma solução de abastecimento «tudo num só local». Os nossos produtos incluem mangueiras hidráulicas, acessórios, adaptadores, acoplamentos rápidos, conectores, protetores de mangueira, equipamento hidráulico e muito mais — tudo o que precisa para garantir que as suas operações decorram de forma harmoniosa e eficiente.
Indique-nos as suas necessidades através do formulário abaixo. A nossa equipa irá responder-lhe com orientação especializada e um orçamento personalizado para garantir o bom funcionamento das suas operações.