High Pressure Compressed Air Hose
A high pressure compressed air hose, also known as an industrial air compressor hose or pneumatic air hose, is a reinforced rubber hose designed for safely transporting compressed air in demanding applications such as mining, construction, and heavy-duty pneumatic tools. Compared to standard air hoses, this flexible high pressure air hose uses wire braided or wire spiral reinforcement to withstand pressures above 300 psi (2 MPa) and prevent bursting, expansion, or leakage. This high pressure compressed air hose is manufactured according to EN 853, EN 856, or SAE 100R standards, with a minimum 4:1 burst safety factor.
Definition:
A high pressure air hose is a wire-reinforced rubber hose designed for compressed air systems operating above 300 psi, typically used in industrial, mining, and construction environments. It is commonly referred to as a compressed air line hose or heavy duty air hose.
Key Takeaway:
If your pneumatic system operates above 300 psi continuously, a standard PVC or single-braid air hose is a safety risk. You need a high pressure compressed air hose with certified burst margin and correct fitting compatibility.
Key Features of High Pressure Compressed Air Hose
| Feature | Value / Benefit |
|---|---|
| Working pressure | Up to 42 MPa (6090 psi) |
| 補強 | Wire braided (1-2 layers) or wire spiral (4-6 layers) |
| Inner tube | Oil-resistant NBR (compatible with lubricated air) |
| Outer cover | Synthetic rubber – abrasion, ozone, UV resistant |
| 温度範囲 | -40°C to +100°C |
| Bend radius | Min 10x OD (wire braided) / 12x OD (wire spiral) |
| Safety factor | 4:1 burst : working pressure |
Technical Specifications (EN & SAE Compliant)
| パラメータ | Wire Braided (1SN/2SN) | Wire Spiral (4SP/4SH) |
|---|---|---|
| Inner diameter (ID) | 6 – 51 mm (1/4″ – 2″) | 10 – 51 mm (3/8″ – 2″) |
| Working pressure | 8 – 25 MPa (1160 – 3625 psi) | 25 – 42 MPa (3625 – 6090 psi) |
| Burst pressure (min) | 4 x working pressure | 4 x working pressure |
| Temperature | -40°C to +100°C | -40°C to +100°C |
| Bend radius | 10 x OD | 12 x OD |
| Standards | EN 853 1SN/2SN, SAE 100R1/R2 | EN 856 4SP, SAE 100R12 |
Download the complete pdf specification sheet for impulse test data, fluid compatibility, and fitting torque values.
Wire Braided vs Wire Spiral High Pressure Air Hose
| Comparison | Wire Braided Hose | Wire Spiral Hose |
|---|---|---|
| Layers | 1 or 2 layers of steel wire braid | 4 or 6 layers of counter-rotating steel wire spiral |
| Max pressure | Up to 25 MPa (3625 psi) | Up to 42 MPa (6090 psi) |
| Flexibility | Better | Good but stiffer |
| Impulse life | Standard | Superior (500,000+ cycles) |
| Best for | Factory air lines, pneumatic tools | Mining drills, heavy jackhammers, marine systems |
| Cost | Lower | Higher |
What pressure air hose do I need for jackhammers?
Most jackhammers require high pressure compressed air hose rated between 300 psi and 6000 psi, depending on the equipment size and duty cycle. For continuous heavy-duty use, choose wire spiral (4SP) construction.
Compressed Air Hose vs PVC Air Hose
| Property | High Pressure Compressed Air Hose (Rubber) | PVC Air Hose |
|---|---|---|
| Max working pressure | Up to 42 MPa (6090 psi) | Typically ≤ 1.5 MPa (215 psi) |
| 温度範囲 | -40°C to +100°C | 0°C to +60°C |
| Abrasion resistance | Excellent | Poor – cracks and wears |
| Flexibility at -20°C | Still flexible | Becomes rigid and cracks |
| Oil resistance | Yes (NBR tube) | No – swells and fails |
| Best for | Mining, construction, industrial | Workshop, light-duty tools |
Conclusion: PVC is cheaper upfront but fails quickly in high-pressure, cold, or oily environments. High pressure compressed air hose (rubber) is the correct choice for demanding applications.
Applications of High Pressure Compressed Air Hose
Air Hose for Mining and Tunneling Equipment
Pneumatic rock drills, roof bolters, air-powered loaders. Requires wire spiral hose up to 42 MPa. Protective sleeves and guards mandatory due to sharp rock contact.
Air Hose for Pneumatic Tools (Jackhammers & Impact Wrenches)
Jackhammers, concrete breakers, air cannons. Wire braided hose (2SN) typically sufficient up to 25 MPa. Crimped fittings recommended over reusable fittings for vibration resistance.
Industrial Air Hose Systems for Factories
Automated assembly lines, robotic grippers, blow-molding machines. Long runs require flanges or adapters for large diameters. Rubber absorbs vibration better than PVC.
Marine and Offshore High Pressure Air Hose
Pneumatic controls, engine air starting systems. Requires corrosion-resistant fittings (stainless steel). ABS or DNV type approval available.
Air Hose for Heavy Construction and Civil Engineering
Pile driving pneumatic hammers, concrete spraying equipment. High abrasion outer cover required (drags over rebar and gravel).
Example Use Case:
A mining contractor using pneumatic rock drills at 35 MPa should select a wire spiral (4SP) high pressure compressed air hose with crimped fittings and protective sleeves to prevent failure under continuous pulse loads.
People Also Ask
What is the best air hose for high pressure?
A wire spiral reinforced rubber air hose is the best choice for high pressure applications above 25 MPa (3625 psi).
What size air hose is best for pneumatic tools?
3/8″ (10 mm) ID is standard for most pneumatic tools. 1/2″ (13 mm) is recommended for high air flow tools like jackhammers.
Can I use rubber air hose for high pressure compressor?
Yes. Rubber air hose with wire braid or wire spiral reinforcement is specifically designed for high pressure compressed air systems.
How long does a high pressure air hose last?
3-5 years in normal industrial use. With proper installation and protection, up to 7 years.
How to Choose the Right High Pressure Compressed Air Hose (5-Step Guide)
Step 1 – Determine maximum working pressure
- Below 25 MPa → Wire braided hose (EN 853 2SN / SAE 100R2)
- Above 25 MPa → Wire spiral hose (EN 856 4SP / SAE 100R12)
Step 2 – Measure required inside diameter (ID)
- 1/4″ (6 mm) → light-duty tools
- 3/8″ (10 mm) → standard industrial
- 1/2″ (13 mm) → heavy tools and long runs
- Larger → use flanges instead of threaded fittings
Step 3 – Select fitting type
- Crimped fittings → permanent, zero leakage, factory-assembled
- Reusable fittings → field repair, prototypes
- Adapters → convert NPT to BSPP or JIC
- Flanges → large bore, high flow
Step 4 – Add protection for harsh environments
- Protective sleeves → abrasion resistance at drag points
- Spiral guards → prevent kinking at sharp bends
Step 5 – Verify certifications
- Request pdf test reports: burst, impulse, ozone resistance
- Confirm EN or SAE marking on the hose
Key Takeaway:
80% of premature hose failures come from wrong pressure rating or mismatched fittings. Always buy a complete hose assembly from a single supplier who controls both components.
Common Problems & Solutions
| Problem | Root Cause | Solution |
|---|---|---|
| Frequent bursting at fitting | Wrong fitting type or improper crimp | Factory hose assembly with crimped fittings |
| Outer cover cracks after 3 months | PVC or low-grade rubber in UV/cold | Synthetic rubber cover with ozone resistance |
| Air leakage reducing tool power | Poor fitting seal or inner tube permeability | NBR inner tube + pre-assembled fittings |
| Hose expands like a balloon | Insufficient reinforcement | Upgrade to wire spiral hose (4+ layers) |
| Fittings corrode offshore | Standard steel fittings | Stainless steel adapters or flanges |
よくある質問
Q1: What is a high pressure compressed air hose?
A: A high pressure compressed air hose is a wire-reinforced rubber hose designed to transport compressed air at pressures above 300 psi with a minimum 4:1 burst safety factor. It meets EN 853, EN 856, or SAE 100R standards.
Q2: Can I use PVC air hose for high pressure?
A: No. PVC air hose is not suitable for high pressure applications because it typically fails above 1.5 MPa (215 psi) and becomes brittle in low temperatures.
Q3: What is the difference between wire braided and wire spiral air hose?
A: Wire braided hose handles pressures up to 25 MPa and is more flexible. Wire spiral hose handles pressures up to 42 MPa and provides superior impulse fatigue resistance for mining and heavy-duty applications.
Q4: What fittings should I use with high pressure compressed air hose?
A: Use crimped fittings for permanent, leak-free installations. Reusable fittings are acceptable for field repairs. Use adapters to convert thread types (NPT/BSPP/JIC) and flanges for diameters above 1.5 inches.
Q5: What pressure air hose do I need for a jackhammer?
A: Most jackhammers require air hoses rated between 300 psi and 6000 psi depending on equipment size and duty cycle. For continuous heavy use, choose wire spiral hose.
Q6: Do you offer OEM ODM for custom hose assemblies?
A: Yes. As a China-based manufacturer, we provide OEM ODM including custom printing, cut-to-length, and pre-assembled hose assemblies with your choice of fittings, protective sleeves, and guards.
Q7: How do I get bulk or wholesale pricing?
A: Contact our sales team with your required diameter, pressure rating, length, and quantity. We offer bulk discount and wholesale pricing for distributors and wholesalers.
Q8: Where can I download the technical specification PDF?
A: Request the PDF datasheet via email. It includes full dimensions, working pressures, burst pressures, bend radii, and fitting compatibility tables.
Q9: What is your supply lead time from your China factory?
A: Standard supply lead time is 15–25 days for bulk orders. Express service is available for urgent projects.
Q10: Is this hose compliant with OSHA and EU safety requirements?
A: Yes. This hose meets EN and SAE standards with a 4:1 safety factor. We can provide compliance documentation for OSHA, CE, and other regional requirements.
Technical Standards & Certifications
| Standard | 説明 |
|---|---|
| EN 853 1SN / 2SN | Wire braided rubber hoses |
| EN 856 4SP | Wire spiral rubber hoses for high pressure |
| SAE 100R2 / R12 | U.S. standard – fully interchangeable |
| ISO 9001:2015 | Factory quality management |
| RoHS / REACH | Chemical compliance for EU export |
| ABS / DNV | Optional marine type approval |
All hoses are 100% proof pressure tested. Third-party test reports available as PDF.
Brand & Quality Assurance – HENGHUA
Years exporting to US/EU markets: Since 2005, HENGHUA has exported high pressure compressed air hose to over 60 countries, including the United States, Germany, Canada, Australia, Chile, and the UAE.
Compliance with OSHA / safety requirements: All hoses meet EN and SAE standards with a 4:1 safety factor. Documentation available for OSHA, CE, and regional safety inspections.
Factory & quality control:
- Raw material incoming inspection (rubber compound, steel wire)
- In-process monitoring (extrusion, spiral/braiding, vulcanization)
- 100% proof pressure testing on every hose
- Laboratory: burst testing (4x WP), impulse cycling (500,000+ cycles)
Customer reference:
*“After switching to HENGHUA’s high pressure compressed air hose for our 150 pneumatic rock drills, hose-related downtime dropped by 75%.”* – Maintenance Manager, Chile Mining Operations
Looking for a reliable air hose supplier or industrial hose manufacturer in China? HENGHUA provides high pressure compressed air hose solutions with full certification and global export experience.
We are your single Source, Supplier, and Solution provider for high pressure compressed air hose.
Contact us to:
- Request a pdf technical datasheet
- Get price / cost estimate for bulk or wholesale orders
- Discuss OEM ODM custom hose assemblies
- Receive free engineering support for hose and fitting selection
- Order samples for testing
当社製品に関するお問い合わせ
当社は、油圧継手および機器のグローバルサプライヤーとして、幅広い業界向けにワンストップの調達ソリューションを提供しています。当社の製品には、以下のものが含まれます。 油圧ホース、継手、アダプター、クイックカップラー、コネクター、ホースガード、油圧機器 その他にも、業務を円滑かつ効率的に進めるために必要なあらゆるものが揃っています。.
以下のフォームからご要望をお知らせください。当社のチームが、お客様の業務が円滑に進むよう、専門的なアドバイスと、お客様に合わせたお見積もりをご提示いたします。.
English 
Spanish 
Portuguese 
French 
German 
Arabic 
Russian 
Indonesian 
Japanese 
Korean