{"id":6413,"date":"2026-10-16T02:19:00","date_gmt":"2026-10-16T02:19:00","guid":{"rendered":"https:\/\/www.henghuahose.com\/?p=6413"},"modified":"2026-10-16T02:19:03","modified_gmt":"2026-10-16T02:19:03","slug":"epdm-steam-hose-230c-construction","status":"publish","type":"post","link":"https:\/\/www.henghuahose.com\/pt\/epdm-steam-hose-230c-construction\/","title":{"rendered":"EPDM Steam Hose 230C: High-Temperature Construction Explained"},"content":{"rendered":"<p>A high temperature steam hose rated 230 \u00b0C is not simply a hotter version of an ordinary steam hose. It is a four-part build: a peroxide-cured EPDM tube, one or two layers of high-tensile steel wire braid, a pin-pricked cover, and end fittings rated for the same duty. That set is what carries the 250 psi (17 bar) working pressure, the 10:1 burst margin and the continuous range down to \u221240 \u00b0C.<\/p>\n\n\n\n<p>Saturated steam lines and modest superheat are where this grade belongs, and the sections below open the EPDM 230 \u00b0C grade layer by layer to show how the figure is verified at the factory.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-the-230-c-figure-actually-buys-you\">What the 230 \u00b0C Figure Actually Buys You<\/h2>\n\n\n\n<p>230 \u00b0C is the top of the HENGHUA EPDM range for continuous steam service. It is a construction claim, not a marketing figure. The same hose is rated down to \u221240 \u00b0C, which matters for outdoor lines that sit idle in winter and then take steam. A 250 \u00b0C intermittent limit covers brief excursions, such as a valve opening wide during start-up.<\/p>\n\n\n\n<p>The step up from the 170 \u00b0C grade to the steam hose 230 \u00b0C grade is not cosmetic. Saturated steam at 17 bar g sits near 207 \u00b0C, so a 170 \u00b0C hose has no margin at that duty. The 230 \u00b0C grade covers it and stays inside its envelope up to roughly 26 bar g on the saturation curve. At 25 bar g the saturation temperature reads about 226 \u00b0C.<\/p>\n\n\n\n<p>The headroom between the steam condition and the hose limit is the real product. The worst day of the year decides the life of a high pressure steam hose, not the average afternoon.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"inside-a-high-temperature-steam-hose-tube-reinforcement-and-cover\">Inside a High Temperature Steam Hose: Tube, Reinforcement and Cover<\/h2>\n\n\n\n<p>A high temperature steam hose is assembled from four elements that all have to agree: the tube, the reinforcement, the cover and the end fitting. If one element is downgraded, the whole hose drops to the level of the weakest link.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Tubo<\/strong> \u2014 a seamless EPDM compound that carries the steam and resists heat aging, hydrolysis and permeation.<\/li>\n\n\n\n<li><strong>Refor\u00e7o<\/strong> \u2014 one or two layers of high-tensile steel wire braid that hold pressure and limit tube swell.<\/li>\n\n\n\n<li><strong>Capa<\/strong> \u2014 a smooth EPDM jacket, pin-pricked around the circumference and along the length.<\/li>\n\n\n\n<li><strong>End fitting<\/strong> \u2014 a bolted safety clamp or a crimped ferrule rated for the same steam condition.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-construction-diagram.jpg\" alt=\"Diagram of a 230 C EPDM steam hose with peroxide cured tube, twin steel wire braid and pin-pricked cover\" class=\"wp-image-6387\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-construction-diagram.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-construction-diagram-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-construction-diagram-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-construction-diagram-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-construction-diagram-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 2. Layer build of the 230 \u00b0C grade: peroxide-cured tube, twin wire braid and a vented cover.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Camada<\/th><th scope=\"col\">Material<\/th><th scope=\"col\">Job at 230 \u00b0C<\/th><th scope=\"col\">What to Verify<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Tubo<\/th><td>Peroxide-cured EPDM<\/td><td>Resists heat aging, hydrolysis and permeation<\/td><td>Compound and cure system on the datasheet<\/td><\/tr><tr><th scope=\"row\">Refor\u00e7o<\/th><td>High-tensile steel wire braid, one or two layers<\/td><td>Holds working pressure and limits swell<\/td><td>Braid count and wire grade<\/td><\/tr><tr><th scope=\"row\">Capa<\/th><td>Pin-pricked EPDM, wrapped finish<\/td><td>Vents gas that permeates the tube<\/td><td>Even perforation along the length<\/td><\/tr><tr><th scope=\"row\">End fitting<\/th><td>Bolted safety clamp or crimped ferrule<\/td><td>Keeps the joint steam-tight<\/td><td>Clamp torque and rated temperature<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>The steam hose tube decides survival. Steam attacks rubber from the inside, where condensate and heat meet the compound at the same time. A peroxide-cured EPDM tube holds its properties longer than a sulfur-cured one under that combination.<\/p>\n\n\n\n<p>The steam hose reinforcement carries the load. A single braid suits most 250 psi duty, while a second layer adds burst margin for larger bores and continuous lines. The steam hose cover is the outer defense against abrasion, oil spray and ultraviolet light.<\/p>\n\n\n\n<p>How the layers share the load is what makes the rating hold. The steam hose tube seals the steam and absorbs the chemical attack. The steam hose reinforcement takes the hoop stress so the tube does not balloon outward. The steam hose cover protects both from the outside, and a different cover finish changes that balance.<\/p>\n\n\n\n<p>None of the three can be judged alone. The steam hose tube, the steam hose reinforcement and the steam hose cover are always specified as a set, and upgrading one while leaving the others untouched rarely lifts the published rating. For the compound side of that story, the notes on <a href=\"https:\/\/www.henghuahose.com\/pt\/epdm-steam-hose-saturated-steam\/\" target=\"_blank\" rel=\"noopener\">EPDM for saturated steam service<\/a> go deeper.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"peroxide-cured-epdm-why-the-cure-system-matters-at-230-c\">Peroxide-Cured EPDM: Why the Cure System Matters at 230 \u00b0C<\/h2>\n\n\n\n<p>The cure system is the quiet variable in a 230 \u00b0C hose. Sulfur-cured EPDM is common at lower temperatures, but sulfur cross-links are less stable when heat and steam work together. Peroxide curing forms carbon-to-carbon cross-links, which resist reversion and compression set better at the top of the range.<\/p>\n\n\n\n<p>On a steam hose 230 \u00b0C running continuously, peroxide curing shows up as a slower loss of hardness and tensile strength. The tube stays smooth rather than cracking, and the hose keeps its pressure rating for longer.<\/p>\n\n\n\n<p>Peroxide curing is not free. It needs a cleaner compound, tighter process control and more energy. That cost is why not every supplier offers it, and why the cure system belongs on the datasheet you compare.<\/p>\n\n\n\n<p>The steam hose tube in this grade is peroxide-cured for exactly that reason. Use the steam hose specification guide to check whether the cure system is actually stated.<\/p>\n\n\n\n<p>A peroxide cure and the braid count are decided together. The cure keeps the tube from softening during a hot soak, and steam hose testing shows the difference first. It only pays off when the steam hose reinforcement is rated for the same duty, so both belong in the same steam hose 230 \u00b0C specification.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"steel-wire-braid-one-layer-or-two\">Steel Wire Braid: One Layer or Two?<\/h2>\n\n\n\n<p>One layer or two is the second decision that shapes the construction. A single braid of high-tensile steel wire covers the standard 250 psi working pressure across most bores. A second layer raises burst margin and stiffens the hose against kinking under vacuum and repeated flexing.<\/p>\n\n\n\n<p>Two layers are worth it when the line runs continuously, when the bore is large, or when the hose is dragged across edges. One layer is lighter and more flexible, which helps where a person handles the hose for a full shift.<\/p>\n\n\n\n<p>A single-braid and a twin-braid build carry the same 250 psi (17 bar) working pressure and the same 2,500 psi (about 172 bar) burst pressure. The difference is margin, not the headline rating. Ask which steam hose reinforcement your duty justifies instead of assuming that more is always better.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"selecting-the-braid-for-a-high-pressure-steam-hose\">Selecting the Braid for a High Pressure Steam Hose<\/h3>\n\n\n\n<p>Braid count is the first question a buyer asks on a high pressure steam hose. The answer depends on the duty. A high pressure steam hose that runs continuously, carries a large bore or flexes near its minimum radius justifies the extra layer. A lighter hose used in short bursts is easier to handle with a single braid.<\/p>\n\n\n\n<p>Wire grade matters as much as layer count. High-tensile steel holds the working pressure with less material, which keeps the hose flexible. A cheaper low-carbon wire forces a thicker, stiffer wall for the same rating. Ask for the wire grade and the layer count together.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"the-pin-pricked-cover-at-high-temperature\">The Pin-Pricked Cover at High Temperature<\/h2>\n\n\n\n<p>A smooth cover looks better in a catalog and fails faster in service. Water vapor and gas permeate the tube under heat, collect between the layers, and push outward. Without a vent, that pressure blisters the steam hose cover or separates the lining.<\/p>\n\n\n\n<p>Pin-pricking (also called a perforated cover) solves it with a pattern of tiny perforations, evenly spaced around the circumference and along the length. The holes are too small to weaken the cover, yet they let the trapped gas escape. ISO 6134:2024 treats this perforated cover as a requirement, not an option.<\/p>\n\n\n\n<p>Two failures follow from a sealed or blocked cover. Blistering lifts the jacket away from the reinforcement. Popcorning, or lining separation, is worse and often appears when a hose is capped at both ends and cools into a vacuum.<\/p>\n\n\n\n<p>An inspection routine should check the steam hose cover for blisters, soft spots and cuts at every shutdown. Start with the <a href=\"https:\/\/www.henghuahose.com\/pt\/hose-failure-analysis-petrochemical-plants\/\" target=\"_blank\" rel=\"noopener\">failure analysis method used in petrochemical plants<\/a> if you want a repeatable checklist.<\/p>\n\n\n\n<p>Cover condition is the first thing to read in any steam hose failure. A blister means gas was trapped inside. A split along the length points to kinking or a bend tighter than the published radius. A hard, cracked jacket points to heat aging. Reading the pattern turns one steam hose failure into a lesson for the whole plant, and it makes steam hose safety checks faster next time.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"high-temperature-steam-hose-ratings-pressure-temperature-and-safety-factor\">High Temperature Steam Hose Ratings: Pressure, Temperature and Safety Factor<\/h2>\n\n\n\n<p>Ratings only mean something when pressure, temperature and safety factor are read together. The 230 \u00b0C grade is rated 250 psi (17 bar) working pressure and 2,500 psi (about 172 bar) burst pressure. That is a 10:1 safety factor, well above the 4:1 typical for hydraulic hose and the 3:1 typical for pneumatic hose.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/high-temperature-steam-hose-rating-chart.jpg\" alt=\"Chart of high temperature steam hose working pressure, burst pressure and temperature limits by bore\" class=\"wp-image-6388\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/high-temperature-steam-hose-rating-chart.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/high-temperature-steam-hose-rating-chart-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/high-temperature-steam-hose-rating-chart-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/high-temperature-steam-hose-rating-chart-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/high-temperature-steam-hose-rating-chart-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 3. The 230 \u00b0C rating envelope by bore: rated pressure, continuous temperature range and minimum bend radius.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Bore<\/th><th scope=\"col\">ID \/ OD (mm)<\/th><th scope=\"col\">Press\u00e3o de funcionamento<\/th><th scope=\"col\">Burst Pressure<\/th><th scope=\"col\">Continuous Range<\/th><th scope=\"col\">Minimum Bend Radius<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">3\/8 in.<\/th><td>10\/21<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>50 mm<\/td><\/tr><tr><th scope=\"row\">1\/2 in.<\/th><td>12\/25<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>60 mm<\/td><\/tr><tr><th scope=\"row\">3\/4 in.<\/th><td>19\/32<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>80 mm<\/td><\/tr><tr><th scope=\"row\">1 in.<\/th><td>25\/39<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>110 mm<\/td><\/tr><tr><th scope=\"row\">1-1\/2 in.<\/th><td>38\/54<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>180 mm<\/td><\/tr><tr><th scope=\"row\">2 in.<\/th><td>51\/67<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>245 mm<\/td><\/tr><tr><th scope=\"row\">3 in.<\/th><td>76\/95<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>400 mm<\/td><\/tr><tr><th scope=\"row\">4 in.<\/th><td>102\/124<\/td><td>250 psi (17 bar)<\/td><td>2,500 psi (172 bar)<\/td><td>\u221240 \u00b0C to 230 \u00b0C<\/td><td>600 mm<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Bulk coils are supplied to a maximum of 100 m, with 40 m and 20 m coils for the larger bores.<\/p>\n\n\n\n<p>ISO 6134:2024 sets a floor rather than a ceiling. Its Type 2 class reaches 18 bar at 210 \u00b0C with steel reinforcement. A steam hose 230 \u00b0C exceeds that temperature, so it has to be verified against the maker&#8217;s own steam test data and not by the standard alone.<\/p>\n\n\n\n<p>That verification is concrete. Every length gets a hydrostatic proof test at 1.5 times its working pressure before shipment. The proof test confirms the finished assembly, not just the raw hose. Ask for the test record when the <a href=\"https:\/\/www.henghuahose.com\/pt\/product\/epdm-high-temperature-steam-hose-230%e2%84%83\/\" target=\"_blank\" rel=\"noopener\">230 \u00b0C product page<\/a> is quoted.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-the-proof-test-proves\">What the Proof Test Proves<\/h3>\n\n\n\n<p>A hydrostatic proof test at 1.5 times working pressure is not a burst test. The proof test confirms that the finished assembly, end fitting included, holds pressure without leaking. The burst test establishes the margin behind the 10:1 safety factor. A complete steam hose testing routine reports both, and repeats the proof test after any re-crimp.<\/p>\n\n\n\n<p>Factory steam hose testing also covers the cover. A perforation check confirms the pin-holing is even and continuous. Most steam hose failure investigations start with the test record, and a steam hose testing log that lists only a burst figure is incomplete.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"where-230-c-sits-against-saturated-and-superheated-steam\">Where 230 \u00b0C Sits Against Saturated and Superheated Steam<\/h2>\n\n\n\n<p>Saturated steam temperature is fixed by pressure. At 17 bar g it is about 207 \u00b0C, and at 25 bar g it is about 226 \u00b0C. The 230 \u00b0C grade therefore covers the saturated curve up to roughly 26 bar g, while the 170 \u00b0C grade stops near 7 bar g.<\/p>\n\n\n\n<p>Superheated steam is a different problem from saturated steam. It is steam heated above its saturation temperature at the same pressure, and it carries no condensate film to soften the attack on the tube. ISO 6134 warns that superheated steam shortens service life, and above the rubber envelope the answer is a PTFE-lined hose or a corrugated metal hose.<\/p>\n\n\n\n<p>A high temperature steam hose suits saturated duty and modest superheat. Applies to saturated lines and short excursions above saturation. For dry superheat, specify a construction rated for that duty rather than one chosen on a datasheet temperature. The saturated versus superheated comparison shows where the boundary falls in practice.<\/p>\n\n\n\n<p>Superheat is also where a high pressure steam hose gets over-specified. A line that never exceeds saturated conditions does not need a superheat-ready construction. Confirm the real steam condition first, then size the hose. That habit protects steam hose safety and avoids paying for envelope you will never use.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"high-temperature-steam-hose-installation-and-warm-up-rules\">High Temperature Steam Hose Installation and Warm-Up Rules<\/h2>\n\n\n\n<p>A high temperature steam hose rewards a disciplined start-up. Open the steam valve slowly and allow two to three minutes of warm-up before full flow. Cold condensate hits the tube hardest, and a fast opening pushes a slug of it down the line.<\/p>\n\n\n\n<p>Route the hose so the bend stays inside its published radius, and support the weight so the end fittings do not carry it. Keep the hose away from hot surfaces and sharp edges. EPDM suits steam and water, and not hydrocarbon media: for mineral oil, diesel or gasoline lines, specify an NBR\/PVC or FKM hose instead.<\/p>\n\n\n\n<p>Retire a hose that shows blistering, cracking, swelling or a soft spot under the cover. Fittings must be a bolted safety clamp or a properly rated crimped ferrule, never a quick-release coupling. If you compare materials across duties, the <a href=\"https:\/\/www.henghuahose.com\/pt\/hydraulic-hose-selection-for-extreme-temperatures\/\" target=\"_blank\" rel=\"noopener\">extreme temperature selection guide<\/a> gives useful context.<\/p>\n\n\n\n<p>The safety rule is simple and absolute. Once a hose shows heat damage, a blister, a deep cut or a leaking joint, replace, never repair.<\/p>\n\n\n\n<p>Personal protection matters as much as the rating. A high temperature steam hose stays hot enough to burn skin long after the valve closes, so wear heat-resistant gloves and route the line clear of walkways. A joint that lets go releases steam and hot condensate under pressure, so check clamp torque before the line is pressurized.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"shutdown-storage-and-steam-hose-safety\">Shutdown, Storage and Steam Hose Safety<\/h3>\n\n\n\n<p>Steam hose safety continues after the shift ends. Close the valve and let the hose cool before it is coiled or moved, because a hot hose kinks and cracks more easily. Drain the condensate so the tube does not sit in water overnight.<\/p>\n\n\n\n<p>Storage is part of steam hose safety too. Keep the hose off the floor, out of direct sun and away from oil. A hose stored correctly between jobs outlasts one left in a puddle. Logged inspections turn an emergency into a planned replacement.<\/p>\n\n\n\n<p>Service life is a range, not a guarantee. In continuous steam duty a high temperature steam hose typically serves two to four years, and an intermittent line five to seven years. Retire on condition first, on age second, and log the date it entered service.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"steam-hose-faqs\">Steam Hose FAQs<\/h2>\n\n\n\n<p><strong>Is a 230 \u00b0C grade necessary for saturated steam?<\/strong> Only above about 7 bar g. Below that, a 170 \u00b0C grade covers the saturated condition with margin. At 17 bar g saturated steam is roughly 207 \u00b0C, and near 25 bar g it reaches about 226 \u00b0C. Those duties need the 230 \u00b0C grade. Check the saturation curve for your pressure before you order.<\/p>\n\n\n\n<p><strong>What does peroxide-cured EPDM change?<\/strong> Peroxide curing forms carbon-to-carbon cross-links instead of sulfur cross-links. Those bonds resist reversion and compression set better when heat and steam act together. The result is a steam hose tube that keeps its hardness and tensile strength longer under continuous 230 \u00b0C duty. The cure system should be named on the datasheet.<\/p>\n\n\n\n<p><strong>How many wire braid layers do I need?<\/strong> One layer of high-tensile steel wire covers the 250 psi working pressure across most bores. Add a second layer for continuous lines, large bores or hoses dragged over edges. The extra braid raises burst margin and stiffens the wall; it does not change the headline pressure rating. Let the duty, not habit, decide.<\/p>\n\n\n\n<p><strong>Why is the cover pin-pricked?<\/strong> Gas and water vapor permeate the tube under heat and collect between the layers. Pin-pricking gives that gas an escape path instead of letting it blister the jacket. ISO 6134:2024 requires an evenly perforated cover for this reason. A smooth, sealed cover is a defect on a steam hose, not a premium feature.<\/p>\n\n\n\n<p><strong>How is the rating verified at the factory?<\/strong> Every length receives a hydrostatic proof test at 1.5 times its working pressure before it leaves the plant. That test confirms the finished assembly holds pressure, not just the raw hose. The 10:1 safety factor between working and burst pressure sits behind the proof figure. Ask for the record with the quote: it should name the length, the 1.5 times rated pressure figure and the batch date code.<\/p>\n\n\n\n<p><strong>Can I use the 230 \u00b0C hose for superheated steam?<\/strong> Only within a small margin. Superheated steam is heated above its saturation temperature and carries no protective condensate. ISO 6134 warns that it shortens service life, and well above the rubber envelope the correct answer is a PTFE-lined or metallic hose. Treat a datasheet temperature as a material limit, not a superheat rating.<\/p>\n\n\n\n<p><strong>When must a high temperature steam hose come out of service?<\/strong> Pull it on any blister, crack, soft spot, swelling or exposed reinforcement. Leaking joints, corroded clamps and hoses that have seen a vacuum collapse are also finished. Heat damage does not heal, and a steam release is dangerous. The rule is replace, never repair, and log the removal date.<\/p>\n\n\n\n<p><strong>Which steam equipment needs a 230 \u00b0C grade rather than a 170 \u00b0C grade?<\/strong> Rubber and tire vulcanizing presses, conveyor-belt splice presses and rubber curing autoclaves are the typical cases, because they run on saturated steam in a range the 170 \u00b0C grade does not cover. Confirm the gauge pressure first, then specify the grade from the steam condition.<\/p>\n\n\n\n<p><strong>I am replacing a 170 \u00b0C hose on a line that runs at 16 bar g. Do I need the 230 \u00b0C grade?<\/strong> Yes. A 16 bar g line runs above the envelope the 170 \u00b0C grade covers, because steam at that pressure is about 204 \u00b0C. Specify the 230 \u00b0C grade, and confirm the end fitting and clamp are rated for that duty. Read the gauge pressure at the point of use, where line losses and valve throttling have already lowered it.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"high-temperature-steam-hose-built-to-your-duty\">High Temperature Steam Hose Built to Your Duty<\/h2>\n\n\n\n<p>HENGHUA manufactures reinforced industrial hose and complete hose assemblies for plants, distributors and OEM brands. Our EPDM steam hose range covers 3\/8 inch to 4 inch bore, rated 250 psi (17 bar) working pressure with a 10:1 burst safety factor.<\/p>\n\n\n\n<p>The construction is a smooth steam-resistant EPDM tube, one or two layers of high-tensile steel wire braid, and a pin-pricked cover that vents permeating gas instead of blistering. Every length is proof-tested at 1.5 times working pressure before it leaves the plant, and each batch is date-coded. Because compounding, extrusion, braiding, vulcanization and crimping all happen in one plant, bulk lead times stay short. Send us the working pressure, the steam temperature, the bore and the end connection, and we will quote against them.<\/p>\n\n\n\n<p>We supply cut lengths, crimped ends, protective sleeves, colour coding and OEM branding. <a href=\"https:\/\/www.henghuahose.com\/pt\/contact\/\" target=\"_blank\" rel=\"noopener\">Get a quote and free samples<\/a><\/p>\n\n\n\n<p>Two quotes for a 230 \u00b0C hose are only comparable when they carry the same four lines. Those are the bore and ID, the pressure rating, the end connection as supplied, and the proof test figure for that length. Ask for all four before you compare price, because a cheaper quote usually differs on one of them.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"final-verdict-buy-the-construction-not-just-the-temperature-number\">Final Verdict: Buy the Construction, Not Just the Temperature Number<\/h2>\n\n\n\n<p>The temperature number on a datasheet is the start of the conversation, not the end of it. A real high temperature steam hose pairs a peroxide-cured tube with the right braid count, a pin-pricked cover and an end fitting rated for the same steam pressure.<\/p>\n\n\n\n<p>Read the whole build before you trust the headline figure. Match the grade to the saturation curve, confirm the proof test and the safety factor, and install the hose with a slow warm-up. If a hose on your line runs hot and fails early, send us the pressure rating, temperature, bore size and end connection. We will quote a construction that fits the duty.<\/p>\n\n\n\n<p>Two habits separate a hose that lasts from one that fails early. The first is verifying the record, because steam hose testing is the only proof that the finished assembly holds its pressure. The second is watching for damage, because most steam hose failure starts small and grows out of sight. Neither job is hard, and both keep the hose inside its rating.<\/p>\n\n\n\n<p><em>Written by the HENGHUA engineering team, with input from plant maintenance and steam-system reliability teams across North America, Europe and South East Asia. HENGHUA manufactures reinforced industrial hose and hose assemblies, including an EPDM steam hose range from 3\/8 inch to 4 inch bore. Those assemblies are rated 250 psi (17 bar) working pressure with a 10:1 burst safety factor, and are supplied as cut lengths or as fully crimped assemblies. Fittings, protective sleeves, colours and OEM branding are available on request. <\/em><\/p>","protected":false},"excerpt":{"rendered":"<p>A high temperature steam hose rated 230 \u00b0C is not simply a hotter version of an ordinary steam hose. It is a four-part build: a peroxide-cured EPDM tube, one or two layers of high-tensile steel wire braid, a pin-pricked cover, and end fittings rated for the same duty. That set is what carries the 250 [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":6386,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_surecart_dashboard_logo_width":"180px","_surecart_dashboard_show_logo":true,"_surecart_dashboard_navigation_orders":true,"_surecart_dashboard_navigation_invoices":true,"_surecart_dashboard_navigation_subscriptions":true,"_surecart_dashboard_navigation_downloads":true,"_surecart_dashboard_navigation_billing":true,"_surecart_dashboard_navigation_account":true,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[1],"tags":[2487,1996,2484,2489,2488],"class_list":["post-6413","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-high-pressure-steam-hose","tag-high-temperature-steam-hose","tag-steam-hose-230","tag-steam-hose-reinforcement","tag-steam-hose-tube"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v24.5 (Yoast SEO v28.1) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>EPDM Steam Hose 230C: High-Temperature Build | HENGHUA<\/title>\n<meta name=\"description\" content=\"Inside an EPDM steam hose 230C: a peroxide cured tube, twin steel wire braid and a pin-pricked cover, rated 250 psi at 230 C with a 10:1 burst margin.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.henghuahose.com\/pt\/epdm-steam-hose-230c-construction\/\" \/>\n<meta property=\"og:locale\" content=\"pt_PT\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"EPDM Steam Hose 230C: High-Temperature Construction Explained\" \/>\n<meta property=\"og:description\" content=\"Inside an EPDM steam hose 230C: a peroxide cured tube, twin steel wire braid and a pin-pricked cover, rated 250 psi at 230 C with a 10:1 burst margin.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.henghuahose.com\/pt\/epdm-steam-hose-230c-construction\/\" \/>\n<meta property=\"og:site_name\" content=\"HENGHUA\" \/>\n<meta property=\"article:published_time\" content=\"2026-10-16T02:19:00+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-10-16T02:19:03+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-hero.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"goodheart786@gmail.com\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Escrito por\" \/>\n\t<meta name=\"twitter:data1\" content=\"goodheart786@gmail.com\" \/>\n\t<meta name=\"twitter:label2\" content=\"Tempo estimado de leitura\" \/>\n\t<meta name=\"twitter:data2\" content=\"16 minutos\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"TechArticle\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/\"},\"author\":{\"name\":\"goodheart786@gmail.com\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\"},\"headline\":\"EPDM Steam Hose 230C: High-Temperature Construction Explained\",\"datePublished\":\"2026-10-16T02:19:00+00:00\",\"dateModified\":\"2026-10-16T02:19:03+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/\"},\"wordCount\":3332,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/epdm-steam-hose-230c-hero.jpg\",\"keywords\":[\"high pressure steam hose\",\"high temperature steam hose\",\"steam hose 230\",\"steam hose reinforcement\",\"steam hose tube\"],\"articleSection\":[\"Blog\"],\"inLanguage\":\"pt-PT\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/\",\"name\":\"EPDM Steam Hose 230C: High-Temperature Build | HENGHUA\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/epdm-steam-hose-230c-hero.jpg\",\"datePublished\":\"2026-10-16T02:19:00+00:00\",\"dateModified\":\"2026-10-16T02:19:03+00:00\",\"description\":\"Inside an EPDM steam hose 230C: a peroxide cured tube, twin steel wire braid and a pin-pricked cover, rated 250 psi at 230 C with a 10:1 burst margin.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#breadcrumb\"},\"inLanguage\":\"pt-PT\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"pt-PT\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/epdm-steam-hose-230c-hero.jpg\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/epdm-steam-hose-230c-hero.jpg\",\"width\":800,\"height\":600,\"caption\":\"EPDM steam hose rated 230 C coiled beside a vulcanizing press steam connection\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/epdm-steam-hose-230c-construction\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.henghuahose.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"EPDM Steam Hose 230C: High-Temperature Construction Explained\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"name\":\"HENGHUA\",\"description\":\"Powering Your Industry, Worldwide.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"alternateName\":\"HENGHUA Hose\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.henghuahose.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"pt-PT\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\",\"name\":\"HENGHUA\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"pt-PT\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"width\":388,\"height\":90,\"caption\":\"HENGHUA\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\",\"name\":\"goodheart786@gmail.com\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"pt-PT\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"caption\":\"goodheart786@gmail.com\"},\"sameAs\":[\"https:\\\/\\\/henghuahose.com\"],\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/pt\\\/author\\\/goodheart786gmail-com\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"EPDM Steam Hose 230C: High-Temperature Build | HENGHUA","description":"Inside an EPDM steam hose 230C: a peroxide cured tube, twin steel wire braid and a pin-pricked cover, rated 250 psi at 230 C with a 10:1 burst margin.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.henghuahose.com\/pt\/epdm-steam-hose-230c-construction\/","og_locale":"pt_PT","og_type":"article","og_title":"EPDM Steam Hose 230C: High-Temperature Construction Explained","og_description":"Inside an EPDM steam hose 230C: a peroxide cured tube, twin steel wire braid and a pin-pricked cover, rated 250 psi at 230 C with a 10:1 burst margin.","og_url":"https:\/\/www.henghuahose.com\/pt\/epdm-steam-hose-230c-construction\/","og_site_name":"HENGHUA","article_published_time":"2026-10-16T02:19:00+00:00","article_modified_time":"2026-10-16T02:19:03+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-hero.jpg","type":"image\/jpeg"}],"author":"goodheart786@gmail.com","twitter_card":"summary_large_image","twitter_misc":{"Escrito por":"goodheart786@gmail.com","Tempo estimado de leitura":"16 minutos"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"TechArticle","@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#article","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/"},"author":{"name":"goodheart786@gmail.com","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7"},"headline":"EPDM Steam Hose 230C: High-Temperature Construction Explained","datePublished":"2026-10-16T02:19:00+00:00","dateModified":"2026-10-16T02:19:03+00:00","mainEntityOfPage":{"@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/"},"wordCount":3332,"commentCount":0,"publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"image":{"@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-hero.jpg","keywords":["high pressure steam hose","high temperature steam hose","steam hose 230","steam hose reinforcement","steam hose tube"],"articleSection":["Blog"],"inLanguage":"pt-PT","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/","url":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/","name":"EPDM Steam Hose 230C: High-Temperature Build | HENGHUA","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#primaryimage"},"image":{"@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-hero.jpg","datePublished":"2026-10-16T02:19:00+00:00","dateModified":"2026-10-16T02:19:03+00:00","description":"Inside an EPDM steam hose 230C: a peroxide cured tube, twin steel wire braid and a pin-pricked cover, rated 250 psi at 230 C with a 10:1 burst margin.","breadcrumb":{"@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#breadcrumb"},"inLanguage":"pt-PT","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/"]}]},{"@type":"ImageObject","inLanguage":"pt-PT","@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#primaryimage","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-hero.jpg","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/epdm-steam-hose-230c-hero.jpg","width":800,"height":600,"caption":"EPDM steam hose rated 230 C coiled beside a vulcanizing press steam connection"},{"@type":"BreadcrumbList","@id":"https:\/\/www.henghuahose.com\/epdm-steam-hose-230c-construction\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.henghuahose.com\/"},{"@type":"ListItem","position":2,"name":"EPDM Steam Hose 230C: High-Temperature Construction Explained"}]},{"@type":"WebSite","@id":"https:\/\/www.henghuahose.com\/#website","url":"https:\/\/www.henghuahose.com\/","name":"HENGHUA","description":"A impulsionar o seu setor, em todo o mundo.","publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"alternateName":"HENGHUA Hose","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.henghuahose.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"pt-PT"},{"@type":"Organization","@id":"https:\/\/www.henghuahose.com\/#organization","name":"HENGHUA","url":"https:\/\/www.henghuahose.com\/","logo":{"@type":"ImageObject","inLanguage":"pt-PT","@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","width":388,"height":90,"caption":"HENGHUA"},"image":{"@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7","name":"goodheart786@gmail.com","image":{"@type":"ImageObject","inLanguage":"pt-PT","@id":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","caption":"goodheart786@gmail.com"},"sameAs":["https:\/\/henghuahose.com"],"url":"https:\/\/www.henghuahose.com\/pt\/author\/goodheart786gmail-com\/"}]}},"_links":{"self":[{"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/posts\/6413","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/comments?post=6413"}],"version-history":[{"count":1,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/posts\/6413\/revisions"}],"predecessor-version":[{"id":6431,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/posts\/6413\/revisions\/6431"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/media\/6386"}],"wp:attachment":[{"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/media?parent=6413"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/categories?post=6413"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.henghuahose.com\/pt\/wp-json\/wp\/v2\/tags?post=6413"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}