{"id":6109,"date":"2026-10-09T09:30:57","date_gmt":"2026-10-09T09:30:57","guid":{"rendered":"https:\/\/www.henghuahose.com\/?p=6109"},"modified":"2026-10-09T09:31:00","modified_gmt":"2026-10-09T09:31:00","slug":"chemical-hose-by-chemical","status":"publish","type":"post","link":"https:\/\/www.henghuahose.com\/ko\/chemical-hose-by-chemical\/","title":{"rendered":"How to Choose the Right Chemical Hose for Each Product"},"content":{"rendered":"<p>Chemical hose compatibility is a matching problem, not a catalog lookup. The fluid decides the liner; the liner sets the temperature and pressure limits; only then do bore and fittings matter. This guide maps seven chemical families onto the liners that survive them, and shows how to read a chemical resistance chart.<\/p>\n\n\n\n<p>Read the fluid the way a chemist would. Name the chemical, note its concentration, and record the temperature at which it moves. Two fluids that share a trade name can demand different liners once those facts change, so read the family map below as a starting point rather than a certificate.<\/p>\n\n\n\n<p><em>About a 15-minute read at 250 words per minute; a family-by-family map from chemical type to liner material, plus the resistance data and standards that support it.<\/em><\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-compatibility-family-map.jpg\" alt=\"Map linking seven chemical families to the chemical hose liner materials each one points to\" class=\"wp-image-6073\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-compatibility-family-map.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-compatibility-family-map-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-compatibility-family-map-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-compatibility-family-map-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-compatibility-family-map-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 1. Seven chemical families drive the liner choice: mineral acids, alkalis, oxidizing agents, aromatic and chlorinated solvents, alcohols and ketones, oils and fuels, and food and pharmaceutical products.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"short-answer-match-the-liner-to-the-chemical-not-the-brand\">Short Answer: Match the Liner to the Chemical, Not the Brand<\/h2>\n\n\n\n<p>A liner that survives one chemical can be destroyed by another. Compatibility depends on four things at once: the exact chemical, its concentration, the service temperature, and how long the fluid sits against the liner. Change any one of them and the answer can flip. The first job is therefore to name the fluid precisely, not to pick a familiar hose.<\/p>\n\n\n\n<p>The failures we see most often in the field start with a fluid that was described loosely. &#8220;Process water&#8221; may carry a trace of chlorinated solvent, and a &#8220;washdown&#8221; may be a caustic that slowly attacks a liner rated only for mild acids. The fix is a habit: write the chemical name, the concentration range, and the peak temperature on the specification before any material is chosen.<\/p>\n\n\n\n<p>Screen the candidates with two filters:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Temperature filter<\/strong> \u2014 a liner that is chemically perfect but runs above its window will age out early.<\/li>\n\n\n\n<li><strong>Contact filter<\/strong> \u2014 a liner rated for splash and intermittent contact is not the same as one rated for continuous immersion.<\/li>\n<\/ul>\n\n\n\n<p>The temperature filter and the contact filter run through the seven families a plant actually moves.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"why-chemical-hose-compatibility-is-a-medium-first-decision\">Why Chemical Hose Compatibility Is a Medium-First Decision<\/h2>\n\n\n\n<p>Buyers often choose a hose by bore and pressure first, then discover the liner cannot handle the fluid. Reversing that order removes a common cause of early failure. The liner is the first layer the fluid meets; the reinforcement and the cover decide how the hose behaves mechanically.<\/p>\n\n\n\n<p>Imagine two lines with identical flow. One carries dilute sulfuric acid, the other an aromatic solvent. The right liner differs even though the bore, the pump and the pressure are the same. Chemical hose compatibility is set by the medium, not by the hardware around it.<\/p>\n\n\n\n<p>Because the medium drives everything downstream, a supplier asks for the fluid before quoting a hose. The liner material then fixes the temperature window, and the window fixes the pressure class and the construction. Get the medium wrong and every later choice inherits the error. The overall map of types and materials sits in the chemical hose complete guide.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"the-seven-chemical-families-a-plant-actually-moves\">The Seven Chemical Families a Plant Actually Moves<\/h2>\n\n\n\n<p>Industrial chemicals are easier to plan for when they are grouped by family rather than by product name. Seven families cover most transfer work, and each one pushes the liner choice in a different direction. Grouping first keeps the shortlist small.<\/p>\n\n\n\n<p>A line may carry more than one of these families over its life, so the most aggressive fluid at its peak temperature sets the specification. Name the family before you open a catalog:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Mineral acids<\/strong> \u2014 sulfuric, hydrochloric, nitric and phosphoric acid, each at a stated concentration.<\/li>\n\n\n\n<li><strong>Alkalis<\/strong> \u2014 caustic soda and caustic potash, often handled as a percentage solution.<\/li>\n\n\n\n<li><strong>Oxidizing agents<\/strong> \u2014 sodium hypochlorite, hydrogen peroxide and similar bleaches.<\/li>\n\n\n\n<li><strong>Aromatic and chlorinated solvents<\/strong> \u2014 toluene, xylene, dichloromethane and related media.<\/li>\n\n\n\n<li><strong>Alcohols and ketones<\/strong> \u2014 methanol, ethanol, acetone and methyl ethyl ketone.<\/li>\n\n\n\n<li><strong>Oils and fuels<\/strong> \u2014 diesel, lubricating oils and other petroleum-based fluids.<\/li>\n\n\n\n<li><strong>Food and pharmaceutical products<\/strong> \u2014 edible oils, syrups and clean-in-place chemicals.<\/li>\n<\/ul>\n\n\n\n<p>A familiar trade name proves nothing on its own. An acid hose is simply a chemical hose whose liner and cover were selected for acid service, so the name describes intent rather than construction.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-does-a-chemical-hose-compatibility-map-show\">What Does a Chemical Hose Compatibility Map Show?<\/h2>\n\n\n\n<p>The table below is the working core of this guide. It maps each family to the liner plants most often use, names a second option, and states what to avoid. Read the &#8220;keep away from&#8221; column first, because eliminating a wrong liner is faster than proving a right one.<\/p>\n\n\n\n<p>Table 1. Chemical family to liner material, with a second option and the materials to avoid.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Chemical family<\/th><th scope=\"col\">First-choice liner<\/th><th scope=\"col\">Also consider<\/th><th scope=\"col\">Keep away from<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Mineral acids (dilute to strong)<\/th><td>EPDM rubber<\/td><td>XLPE, or PTFE for strong or hot acids<\/td><td>UHMWPE for strong oxidizing acids such as nitric<\/td><\/tr><tr><th scope=\"row\">Alkalis (caustic soda, caustic potash)<\/th><td>XLPE<\/td><td>EPDM, or PTFE for hot caustic<\/td><td>FKM, which is not for hot alkalis<\/td><\/tr><tr><th scope=\"row\">Oxidizing agents (sodium hypochlorite)<\/th><td>XLPE<\/td><td>PTFE for hot or strong oxidizers<\/td><td>UHMWPE where the oxidizer is strong<\/td><\/tr><tr><th scope=\"row\">Aromatic and chlorinated solvents<\/th><td>PTFE<\/td><td>FKM for some hydrocarbon duties<\/td><td>XLPE (not for aromatic solvents), UHMWPE at high temperature, EPDM<\/td><\/tr><tr><th scope=\"row\">Alcohols and ketones<\/th><td>EPDM<\/td><td>PTFE for hot or mixed duties<\/td><td>NBR and FKM, neither of which suits ketones<\/td><\/tr><tr><th scope=\"row\">Oils and fuels (petroleum based)<\/th><td>Oil-resistant synthetic rubber (NBR)<\/td><td>UHMWPE for mixed plant service<\/td><td>EPDM, which swells in petroleum oils and aromatics<\/td><\/tr><tr><th scope=\"row\">Food and pharmaceutical products<\/th><td>UHMWPE or PTFE to food-contact rules<\/td><td>EPDM with the right documentation<\/td><td>Unidentified compounds without food-contact paperwork<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Note: food and pharmaceutical duties add a documentation layer. Polyolefin liners are commonly assessed against FDA 21 CFR 177.1520, and plastic food-contact materials against EU 10\/2011. Our <a href=\"https:\/\/www.henghuahose.com\/ko\/product\/food-discharge-hose-150psi\/\" target=\"_blank\" rel=\"noopener\">food discharge hose<\/a> is one example of that build.<\/p>\n\n\n\n<p>Three cautions sit behind the map. First, a liner that suits a family at low concentration can fail at high concentration, so the table assumes the strength is stated. Second, a blend or a waste stream behaves like its most aggressive component, not like its average. Third, a fluid that permeates the liner reaches the reinforcement and the cover from the inside, so the damage surfaces later than the chemistry that caused it.<\/p>\n\n\n\n<p>For duties that mix a strong acid with an aromatic solvent, PTFE is usually the single answer, because it is nearly inert against both. The wider trade-off between the three thermoplastics is set out in the comparison of rubber vs PTFE vs UHMWPE hose, while the pure material properties are collected in the flexible hose materials guide.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"how-to-read-a-chemical-resistance-chart\">How to Read a Chemical Resistance Chart<\/h2>\n\n\n\n<p>A chemical resistance chart is a table that lists fluids against materials and marks how each combination behaves. The mark is a rating, not a guarantee, and it means something only when you also read the four conditions behind it. Skip those conditions and the chart can mislead.<\/p>\n\n\n\n<p>Table 2. The four conditions behind every entry in a resistance chart, and how each one changes the verdict.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Condition<\/th><th scope=\"col\">What it records<\/th><th scope=\"col\">How it shifts the rating<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Chemical and concentration<\/th><td>The exact medium and its strength<\/td><td>A dilution that is safe can turn aggressive when concentrated<\/td><\/tr><tr><th scope=\"row\">Temperature<\/th><td>The service temperature of the fluid<\/td><td>Most liners lose resistance as temperature rises toward the window limit<\/td><\/tr><tr><th scope=\"row\">Contact time<\/th><td>Continuous, intermittent or splash exposure<\/td><td>A liner for splash duty may swell under continuous immersion<\/td><\/tr><tr><th scope=\"row\">Rating scale<\/th><td>The letters or grades the supplier uses<\/td><td>Read the legend, because scales differ between suppliers<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-resistance-chart-reading-guide.jpg\" alt=\"Diagram showing the four conditions behind a chemical resistance chart rating\" class=\"wp-image-6074\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-resistance-chart-reading-guide.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-resistance-chart-reading-guide-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-resistance-chart-reading-guide-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-resistance-chart-reading-guide-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-resistance-chart-reading-guide-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 2. A rating only holds under the conditions it was measured at, so read the chemical, the temperature, the contact time and the rating scale together before trusting an entry.<\/p>\n\n\n\n<p>Concentration sets the strength the liner has to survive. A rating taken on a dilute acid can fall to fair or poor once the fluid is concentrated, so match the rating to the strength the line actually sees. An acid hose marked excellent for phosphoric acid may sit lower for nitric, so match the acid, not the family.<\/p>\n\n\n\n<p>A neutral pH does not make a solvent safe: pH describes acid and base strength, while solvent attack works by a different mechanism.<\/p>\n\n\n\n<p>Temperature moves the verdict in one direction: almost every liner loses resistance as it approaches the top of its window, so a rating measured at room temperature does not cover a hot transfer. Plan against the peak temperature rather than the average.<\/p>\n\n\n\n<p>Contact time changes the verdict as much as temperature does. A hose that fills a drum once a day sees far less attack than a hose that holds the same fluid for weeks.<\/p>\n\n\n\n<p>The rating scale is the part we see misread most often in supplier questions. Suppliers use letters, words or numbers, and the legend defines them. Read the legend first, then check whether the entry assumes continuous or intermittent contact. Chemical hose compatibility rarely depends on the cover, so judge against the liner the chart names.<\/p>\n\n\n\n<p>Two habits keep a chart honest:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Confirm the exact compound<\/strong> \u2014 a family name such as &#8220;EPDM&#8221; covers many formulations, and they do not perform identically.<\/li>\n\n\n\n<li><strong>Treat the chart as a screen<\/strong> \u2014 use it to eliminate materials, then confirm the survivor with the manufacturer&#8217;s published data.<\/li>\n<\/ul>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-temperature-and-pressure-limits-apply-to-chemical-hose-compatibility\">What Temperature and Pressure Limits Apply to Chemical Hose Compatibility?<\/h2>\n\n\n\n<p>Every liner has a temperature window, and that window is a planning value for continuous service rather than a spike limit. Running a liner above its window does not fail it at once; it shortens life and speeds up the chemical attack that is already underway. Chemical hose compatibility is valid only inside that window, as well as against the fluid.<\/p>\n\n\n\n<p>Table 3. Liner materials for chemical hose, with planning temperature windows and the fluids each one serves or struggles with.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Liner material<\/th><th scope=\"col\">Planning temperature window<\/th><th scope=\"col\">Serves well<\/th><th scope=\"col\">Keep away from<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">PTFE<\/th><td>\u221270 \u00b0C to +260 \u00b0C<\/td><td>Strong acids, bases and solvents; the widest chemical reach<\/td><td>Molten alkali metals and elemental fluorine<\/td><\/tr><tr><th scope=\"row\">UHMWPE (UPE)<\/th><td>\u221240 \u00b0C to +120 \u00b0C<\/td><td>Broad industrial coverage; data sheets commonly state about 98% of chemicals<\/td><td>Strong oxidizing acids, and some hot aromatics or chlorinated hydrocarbons<\/td><\/tr><tr><th scope=\"row\">XLPE<\/th><td>\u221240 \u00b0C to +100 \u00b0C<\/td><td>Acids, bases and oxidizing media such as hypochlorite<\/td><td>Aromatic solvents<\/td><\/tr><tr><th scope=\"row\">EPDM rubber<\/th><td>\u221240 \u00b0C to +120 \u00b0C<\/td><td>Acids, bases, ketones, alcohols, ozone and steam<\/td><td>Petroleum-based oils and aromatics<\/td><\/tr><tr><th scope=\"row\">Oil-resistant synthetic rubber (NBR)<\/th><td>\u221230 \u00b0C to +100 \u00b0C<\/td><td>Petroleum-based oils and fuels<\/td><td>Ketones, esters, strong acids and ozone<\/td><\/tr><tr><th scope=\"row\">FKM (fluoroelastomer)<\/th><td>\u221220 \u00b0C to +200 \u00b0C<\/td><td>Hydrocarbons, acids and high temperature<\/td><td>Hot alkalis, ketones and amines<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-liner-temperature-windows.jpg\" alt=\"Bar comparison of chemical hose liner temperature windows for PTFE, FKM, UHMWPE, EPDM, XLPE and NBR, widest span first\" class=\"wp-image-6075\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-liner-temperature-windows.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-liner-temperature-windows-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-liner-temperature-windows-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-liner-temperature-windows-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-liner-temperature-windows-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 3. Planning temperature windows for six chemical hose liners; PTFE covers the widest span and NBR the narrowest.<\/p>\n\n\n\n<p>Pressure sets the other limit. Common chemical hose ratings are 150 PSI, about 10 bar, for general service, 16 bar for heavier transfer, and 17 bar for XLPE suction and discharge constructions. Burst pressure sits at roughly three to four times the working pressure as a planning figure.<\/p>\n\n\n\n<p>Construction follows the pressure duty. A delivery hose (Type D) carries fluid under positive pressure only, while a suction and delivery hose (Type SD) adds a steel helix that resists collapse under vacuum. The layer difference and the fittings each type needs are covered in <a href=\"https:\/\/www.henghuahose.com\/ko\/suction-hose-vs-delivery-hose\/\" target=\"_blank\" rel=\"noopener\">suction hose vs delivery hose<\/a>. Electrical class belongs here too, because flammable media need a defined resistance to ground.<\/p>\n\n\n\n<p>For flammable service, EN 12115:2021 separates delivery (Type D) from suction and delivery (Type SD), splits hoses into four electrical classes, and covers \u221220 \u00b0C to +65 \u00b0C at its 10 bar working pressure. The electrical test follows EN ISO 8031, with a conductive class at or below 10\u2076 ohms and a static-dissipative class at or below 10\u2079 ohms.<\/p>\n\n\n\n<p>Table 4. Pressure and electrical references that sit alongside compatibility when a line is specified.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Item<\/th><th scope=\"col\">Common value or class<\/th><th scope=\"col\">Why it matters<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Working pressure<\/th><td>150 PSI (about 10 bar), 16 bar or 17 bar<\/td><td>Sets the reinforcement and the class of hose<\/td><\/tr><tr><th scope=\"row\">Electrical class<\/th><td>Conductive (10\u2076 ohms or below) or static-dissipative (10\u2079 ohms or below)<\/td><td>Drains static on flammable and combustible service<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Bonding and grounding are two separate actions, and transfer work needs both. Grounding connects equipment to earth, while bonding equalizes potential between the hose, the container and the equipment, and OSHA requirements for bonding and grounding apply wherever a container cannot be grounded directly.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"why-do-solvents-and-fuels-damage-hose-liners\">Why Do Solvents and Fuels Damage Hose Liners?<\/h2>\n\n\n\n<p>Solvents and petroleum fluids cause the failures that are hardest to spot, because they develop slowly. A liner does not crack in a day; it swells, softens or hardens over weeks until a coupling or a bend gives way. Oils and fuels are where chemical hose compatibility is assumed rather than checked.<\/p>\n\n\n\n<p>Aromatic and chlorinated solvents attack the polyolefin liners. XLPE is not for aromatic solvents, and UHMWPE tolerates only some of them at moderate temperature, so a solvent hose for aromatic duty usually means PTFE. FKM resists hydrocarbons and can suit some petroleum-based duties, but it is not for ketones, hot alkalis or amines.<\/p>\n\n\n\n<p>Oils and fuels run the opposite way. EPDM takes up petroleum fluids and swells, so it is the wrong choice for diesel, lubricants and fuel blends. The match is an oil-resistant synthetic rubber, usually an NBR compound, which is built for petroleum fluids and carries its own keep-away list.<\/p>\n\n\n\n<p>The lesson for both families is the same: specify by the fluid and the liner; the cover color and the product name carry no compatibility information. A fuel hose and a solvent hose can look identical from the outside, and only the liner tells them apart. The wider picture for petroleum fluids is in the <a href=\"https:\/\/www.henghuahose.com\/ko\/oil-resistant-hose-guide\/\" target=\"_blank\" rel=\"noopener\">oil-resistant hose guide<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-should-a-chemical-hose-specification-include\">What Should a Chemical Hose Specification Include?<\/h2>\n\n\n\n<p>A written specification is how chemical hose compatibility becomes a purchase order. It answers the supplier&#8217;s first questions before they are asked, which reduces the risk of a wrong shipment.<\/p>\n\n\n\n<p>Write the fluid facts first, then the mechanical facts:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The exact chemical name, its concentration range and its normal and peak temperature.<\/li>\n\n\n\n<li>The working pressure and whether the line also runs under vacuum.<\/li>\n\n\n\n<li>The bore, the length and the end fittings, matched to the flow and the connection.<\/li>\n\n\n\n<li>The liner material and the standard the hose must meet.<\/li>\n\n\n\n<li>The electrical class if the fluid is flammable or combustible.<\/li>\n\n\n\n<li>Cover, marking, packaging and any documentation the site requires.<\/li>\n<\/ul>\n\n\n\n<p>Bore is the field that comes up wrong most often in our inquiries. Sizing from the flow rate rather than the pipe thread avoids a hose that starves the pump, and the method is set out in the hose size selection guide. The inner-tube logic that underpins the liner choice, by compound, is explained in the guide to <a href=\"https:\/\/www.henghuahose.com\/ko\/hydraulic-hose-fluid-compatibility-chart-nbr-vs-epdm-vs-fkm-inner-tube-selection-guide\/\" target=\"_blank\" rel=\"noopener\">NBR, EPDM and FKM inner tube compatibility<\/a>.<\/p>\n\n\n\n<p>Testing standards settle the paperwork side. Hydrostatic testing to ISO 1402 and impulse testing to ISO 6803 confirm that a hose still holds pressure and survives cycling. Keep the records with the hose.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"chemical-hose-compatibility-faqs\">Chemical Hose Compatibility FAQs<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-does-chemical-hose-compatibility-mean\">What does chemical hose compatibility mean?<\/h3>\n\n\n\n<p>It means the liner can carry a specific fluid at a specific concentration and temperature without degrading faster than expected. It is never a property of a hose on its own, because the same liner can suit one chemical and fail another. Compatibility is confirmed for a named medium, a stated strength and a stated temperature, and it should be checked against the manufacturer&#8217;s published data rather than assumed.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"which-liner-handles-the-widest-range-of-chemicals\">Which liner handles the widest range of chemicals?<\/h3>\n\n\n\n<p>PTFE covers the widest range. It is nearly inert against strong acids, bases and solvents, and it holds that resistance from \u221270 \u00b0C to +260 \u00b0C, the broadest window of any common liner. Two exclusions matter: molten alkali metals and elemental fluorine. UHMWPE is next, with manufacturer data sheets commonly stating coverage of about 98% of industrial chemicals, though strong oxidizing acids are an exception.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"can-one-chemical-hose-handle-both-acids-and-solvents\">Can one chemical hose handle both acids and solvents?<\/h3>\n\n\n\n<p>Sometimes, but only when a single liner really covers both fluids. PTFE is the usual answer, because it resists many strong acids and many solvents at once. Rubber and polyolefin liners are less forgiving: a liner that fights acids well may still swell in an aromatic solvent, so check both fluids against the data sheet.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"why-does-concentration-change-a-resistance-rating\">Why does concentration change a resistance rating?<\/h3>\n\n\n\n<p>A rating is measured at one strength, so it does not transfer to another. A liner marked good for dilute sulfuric acid can drop to fair or poor when the same acid is concentrated, because the aggressive fraction is higher. State the strongest concentration the line will see, including cleaning and upset batches, and read the rating against that figure.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"is-an-acid-hose-different-from-a-general-chemical-hose\">Is an acid hose different from a general chemical hose?<\/h3>\n\n\n\n<p>Not in construction, only in intent. An acid hose is a chemical hose specified for acid service, which is why the name survives in trade lists. It follows the same rules as any other chemical hose: a liner matched to the fluid, a reinforcement for pressure, and a helix if the line also runs under vacuum. Treat the liner data sheet as the proof of compatibility.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-is-the-best-liner-for-aromatic-solvents\">What is the best liner for aromatic solvents?<\/h3>\n\n\n\n<p>PTFE is the safe answer for aromatic and chlorinated solvents, because it resists the attack that breaks down polyolefin liners. Two questions settle the rest. Does the duty run hot, where UHMWPE weakens at the top of its window? Is the fluid a ketone, a hot alkali or an amine, the three media FKM cannot take?<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"can-an-epdm-chemical-hose-carry-diesel-or-lubricating-oil\">Can an EPDM chemical hose carry diesel or lubricating oil?<\/h3>\n\n\n\n<p>EPDM is built for acids, bases and steam service, but it takes up petroleum-based oils and aromatics and swells. Fuels and lubricants therefore need a different liner. For these duties, specify an NBR compound: it is the liner built for petroleum fluids, and it should not be used where ketones, esters, strong acids or ozone are present.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-do-temperature-and-contact-time-change-the-choice\">How do temperature and contact time change the choice?<\/h3>\n\n\n\n<p>Both push a liner toward its limits, and they compound. A rating measured cold does not cover a hot transfer, because almost every material loses resistance as temperature rises toward the top of its window. Long contact works the same way on a liner built for short exposure. Plan against the peak temperature and the longest contact the line will see.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-is-the-difference-between-a-solvent-hose-and-a-fuel-hose\">What is the difference between a solvent hose and a fuel hose?<\/h3>\n\n\n\n<p>The liner, not the cover. A solvent hose for aromatic or chlorinated duty usually means a PTFE liner, because those media attack polyolefin liners. A fuel hose for petroleum products usually means an oil-resistant synthetic rubber such as NBR. Ask for the liner compound in writing before ordering, because the outside of a hose says nothing about it.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"does-compatibility-cover-the-fittings-and-seals-too\">Does compatibility cover the fittings and seals too?<\/h3>\n\n\n\n<p>Every wetted part has to tolerate the fluid, not only the liner. A liner that suits the medium can still fail at a joint when the fitting or the seal is corroded or swollen by the same fluid. Check the wetted path as one list: liner, fitting, seal and gasket.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-do-i-confirm-a-liner-before-ordering\">How do I confirm a liner before ordering?<\/h3>\n\n\n\n<p>Reduce the choice to a written specification: the exact chemical, the concentration range, the peak temperature, the working pressure, whether the line runs under vacuum, and the bore. Ask the supplier for the data sheet of the specific compound, not the family, and treat the published resistance data as the deciding document.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"about-henghua-and-how-to-order-a-chemical-hose\">About HENGHUA and How to Order a Chemical Hose<\/h2>\n\n\n\n<p>HENGHUA manufactures chemical hose and hose assemblies for global distributors, retailers and OEM brands. The chemical hose line covers UHMWPE (UPE), XLPE and PTFE liners alongside rubber constructions in EPDM and oil-resistant synthetic rubber, all built on high-tensile textile reinforcement, with a steel helix added for suction service. Factory-crimped assemblies, custom lengths, fittings, cover printing, private label and OEM\/ODM work are all available.<\/p>\n\n\n\n<p>Because compounding, extrusion, reinforcement and crimping stay in one plant, lead times typically stay short for bulk orders, and the specification on the label is the specification supplied. Commercial terms follow factory-direct pricing with warranty support. If you are sourcing chemical hose for distribution or for plant use, send the fluid, its concentration, the temperature, the pressure and the bore, and we will match the liner and quote against them.<\/p>\n\n\n\n<p><a href=\"https:\/\/www.henghuahose.com\/ko\/contact\/\" target=\"_blank\" rel=\"noopener\">Get a quote and free samples<\/a><\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"final-verdict\">Final Verdict<\/h2>\n\n\n\n<p>Chemical hose compatibility is decided by the fluid, confirmed by the liner, and only then bounded by temperature and pressure. Work in that order and the hose fits the duty; skip a step and the shortfall appears later as a swollen liner, a cracked cover or a coupling that lets go at the worst moment.<\/p>\n\n\n\n<p>Three habits carry most of the weight. Group the medium by family before opening a catalog. Read every resistance rating against its concentration, temperature and contact time. And for flammable service, treat grounding and bonding as part of the build rather than an accessory. Combine those with a written specification, and choosing a chemical hose for each product becomes a repeatable method rather than a guess.<\/p>","protected":false},"excerpt":{"rendered":"<p>Chemical hose compatibility is a matching problem, not a catalog lookup. The fluid decides the liner; the liner sets the temperature and pressure limits; only then do bore and fittings matter. This guide maps seven chemical families onto the liners that survive them, and shows how to read a chemical resistance chart. Read the fluid [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":6076,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_surecart_dashboard_logo_width":"180px","_surecart_dashboard_show_logo":true,"_surecart_dashboard_navigation_orders":true,"_surecart_dashboard_navigation_invoices":true,"_surecart_dashboard_navigation_subscriptions":true,"_surecart_dashboard_navigation_downloads":true,"_surecart_dashboard_navigation_billing":true,"_surecart_dashboard_navigation_account":true,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[1],"tags":[2291,2289,2290,2293,2292],"class_list":["post-6109","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-acid-hose","tag-chemical-hose-compatibility","tag-chemical-resistance-chart","tag-en-121152021","tag-solvent-hose"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v24.5 (Yoast SEO v28.1) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Chemical Hose Compatibility: Choose by Chemical | HENGHUA<\/title>\n<meta name=\"description\" content=\"A chemical hose compatibility guide: map acids, solvents, oils and oxidizers to the right liner, then set the temperature and pressure limits for each duty.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.henghuahose.com\/ko\/chemical-hose-by-chemical\/\" \/>\n<meta property=\"og:locale\" content=\"ko_KR\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"How to Choose the Right Chemical Hose for Each Product\" \/>\n<meta property=\"og:description\" content=\"A chemical hose compatibility guide: map acids, solvents, oils and oxidizers to the right liner, then set the temperature and pressure limits for each duty.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.henghuahose.com\/ko\/chemical-hose-by-chemical\/\" \/>\n<meta property=\"og:site_name\" content=\"HENGHUA\" \/>\n<meta property=\"article:published_time\" content=\"2026-10-09T09:30:57+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-10-09T09:31:00+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-by-chemical-hero.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"goodheart786@gmail.com\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"\uae00\uc4f4\uc774\" \/>\n\t<meta name=\"twitter:data1\" content=\"goodheart786@gmail.com\" \/>\n\t<meta name=\"twitter:label2\" content=\"\uc608\uc0c1 \ub418\ub294 \ud310\ub3c5 \uc2dc\uac04\" \/>\n\t<meta name=\"twitter:data2\" content=\"17\ubd84\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"TechArticle\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/\"},\"author\":{\"name\":\"goodheart786@gmail.com\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\"},\"headline\":\"How to Choose the Right Chemical Hose for Each Product\",\"datePublished\":\"2026-10-09T09:30:57+00:00\",\"dateModified\":\"2026-10-09T09:31:00+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/\"},\"wordCount\":3472,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/chemical-hose-by-chemical-hero.jpg\",\"keywords\":[\"acid hose\",\"chemical hose compatibility\",\"chemical resistance chart\",\"EN 12115:2021\",\"solvent hose\"],\"articleSection\":[\"Blog\"],\"inLanguage\":\"ko-KR\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/\",\"name\":\"Chemical Hose Compatibility: Choose by Chemical | HENGHUA\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/chemical-hose-by-chemical-hero.jpg\",\"datePublished\":\"2026-10-09T09:30:57+00:00\",\"dateModified\":\"2026-10-09T09:31:00+00:00\",\"description\":\"A chemical hose compatibility guide: map acids, solvents, oils and oxidizers to the right liner, then set the temperature and pressure limits for each duty.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#breadcrumb\"},\"inLanguage\":\"ko-KR\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"ko-KR\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/chemical-hose-by-chemical-hero.jpg\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/chemical-hose-by-chemical-hero.jpg\",\"width\":800,\"height\":600,\"caption\":\"Cut edge of a chemical hose assembly showing cover, textile reinforcement, liner and hollow bore beside a crimped end fitting\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/chemical-hose-by-chemical\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.henghuahose.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"How to Choose the Right Chemical Hose for Each Product\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"name\":\"HENGHUA\",\"description\":\"Powering Your Industry, Worldwide.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"alternateName\":\"HENGHUA Hose\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.henghuahose.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"ko-KR\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\",\"name\":\"HENGHUA\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ko-KR\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"width\":388,\"height\":90,\"caption\":\"HENGHUA\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\",\"name\":\"goodheart786@gmail.com\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"ko-KR\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"caption\":\"goodheart786@gmail.com\"},\"sameAs\":[\"https:\\\/\\\/henghuahose.com\"],\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/ko\\\/author\\\/goodheart786gmail-com\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Chemical Hose Compatibility: Choose by Chemical | HENGHUA","description":"A chemical hose compatibility guide: map acids, solvents, oils and oxidizers to the right liner, then set the temperature and pressure limits for each duty.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.henghuahose.com\/ko\/chemical-hose-by-chemical\/","og_locale":"ko_KR","og_type":"article","og_title":"How to Choose the Right Chemical Hose for Each Product","og_description":"A chemical hose compatibility guide: map acids, solvents, oils and oxidizers to the right liner, then set the temperature and pressure limits for each duty.","og_url":"https:\/\/www.henghuahose.com\/ko\/chemical-hose-by-chemical\/","og_site_name":"HENGHUA","article_published_time":"2026-10-09T09:30:57+00:00","article_modified_time":"2026-10-09T09:31:00+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-by-chemical-hero.jpg","type":"image\/jpeg"}],"author":"goodheart786@gmail.com","twitter_card":"summary_large_image","twitter_misc":{"\uae00\uc4f4\uc774":"goodheart786@gmail.com","\uc608\uc0c1 \ub418\ub294 \ud310\ub3c5 \uc2dc\uac04":"17\ubd84"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"TechArticle","@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#article","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/"},"author":{"name":"goodheart786@gmail.com","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7"},"headline":"How to Choose the Right Chemical Hose for Each Product","datePublished":"2026-10-09T09:30:57+00:00","dateModified":"2026-10-09T09:31:00+00:00","mainEntityOfPage":{"@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/"},"wordCount":3472,"commentCount":0,"publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"image":{"@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-by-chemical-hero.jpg","keywords":["acid hose","chemical hose compatibility","chemical resistance chart","EN 12115:2021","solvent hose"],"articleSection":["Blog"],"inLanguage":"ko-KR","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/","url":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/","name":"Chemical Hose Compatibility: Choose by Chemical | HENGHUA","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#primaryimage"},"image":{"@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-by-chemical-hero.jpg","datePublished":"2026-10-09T09:30:57+00:00","dateModified":"2026-10-09T09:31:00+00:00","description":"A chemical hose compatibility guide: map acids, solvents, oils and oxidizers to the right liner, then set the temperature and pressure limits for each duty.","breadcrumb":{"@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#breadcrumb"},"inLanguage":"ko-KR","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/"]}]},{"@type":"ImageObject","inLanguage":"ko-KR","@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#primaryimage","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-by-chemical-hero.jpg","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/chemical-hose-by-chemical-hero.jpg","width":800,"height":600,"caption":"Cut edge of a chemical hose assembly showing cover, textile reinforcement, liner and hollow bore beside a crimped end fitting"},{"@type":"BreadcrumbList","@id":"https:\/\/www.henghuahose.com\/chemical-hose-by-chemical\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.henghuahose.com\/"},{"@type":"ListItem","position":2,"name":"How to Choose the Right Chemical Hose for Each Product"}]},{"@type":"WebSite","@id":"https:\/\/www.henghuahose.com\/#website","url":"https:\/\/www.henghuahose.com\/","name":"HENGHUA","description":"Powering Your Industry, Worldwide.","publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"alternateName":"HENGHUA Hose","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.henghuahose.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"ko-KR"},{"@type":"Organization","@id":"https:\/\/www.henghuahose.com\/#organization","name":"HENGHUA","url":"https:\/\/www.henghuahose.com\/","logo":{"@type":"ImageObject","inLanguage":"ko-KR","@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","width":388,"height":90,"caption":"HENGHUA"},"image":{"@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7","name":"goodheart786@gmail.com","image":{"@type":"ImageObject","inLanguage":"ko-KR","@id":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","caption":"goodheart786@gmail.com"},"sameAs":["https:\/\/henghuahose.com"],"url":"https:\/\/www.henghuahose.com\/ko\/author\/goodheart786gmail-com\/"}]}},"_links":{"self":[{"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/posts\/6109","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/comments?post=6109"}],"version-history":[{"count":1,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/posts\/6109\/revisions"}],"predecessor-version":[{"id":6127,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/posts\/6109\/revisions\/6127"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/media\/6076"}],"wp:attachment":[{"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/media?parent=6109"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/categories?post=6109"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.henghuahose.com\/ko\/wp-json\/wp\/v2\/tags?post=6109"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}