{"id":4438,"date":"2026-09-08T03:10:10","date_gmt":"2026-09-08T03:10:10","guid":{"rendered":"https:\/\/www.henghuahose.com\/?p=4438"},"modified":"2026-09-08T03:10:13","modified_gmt":"2026-09-08T03:10:13","slug":"tank-truck-hose-guide","status":"publish","type":"post","link":"https:\/\/www.henghuahose.com\/fr\/tank-truck-hose-guide\/","title":{"rendered":"Tank Truck Hose: Specs, Standards &#038; Assemblies"},"content":{"rendered":"<p>A tank truck hose is a flexible, conductive rubber hose assembly that loads and unloads petrol, diesel and fuel oil on and off road tankers \u2014 rated 150 PSI (10 bar) working pressure, full vacuum, in 2 to 4 inch bores, to EN 1761, EN 1765 or ISO 1823. If you are replacing a hose, checking a quotation, or specifying factory-made tank truck hose assemblies with camlock, threaded or flanged ends, this guide covers the four numbers that matter \u2014 pressure, size, vacuum and temperature \u2014 plus the standards printed on the cover and exactly what to tell your supplier when you order. This guide is for fleet buyers, depot operators and maintenance managers who replace or re-order truck-side hose assemblies.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-what-does-this-hose-do-on-a-road-tanker\">What Does This Hose Do on a Road Tanker?<\/h2>\n\n\n\n<p>Can one hose really work on both sides of the pump \u2014 pulling fuel out of an underground tank on suction, then pushing it out under pressure on discharge? Yes, if it is built with a wire helix. This hose is the line that connects a road tanker&#8217;s compartment or pump to a loading arm, a depot manifold, or a customer&#8217;s tank; it must hold vacuum while the pump pulls product out of an underground tank, then carry the same product under pressure on the discharge side. That double duty is why the hose is built with a wire helix, not textile alone \u2014 the helix keeps the bore round under suction.<\/p>\n\n\n\n<p>The construction follows the same three-layer logic as other petroleum hoses, with one addition that matters on a truck:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Tube:<\/strong> an oil-resistant nitrile (NBR) inner layer, smooth-bore and conductive, so static charge drains instead of building up while fuel flows.<\/li>\n\n\n\n<li><strong>Reinforcement:<\/strong> high-tensile textile plies for pressure, plus a spiral steel wire helix for vacuum resistance.<\/li>\n\n\n\n<li><strong>Cover:<\/strong> an oil-, abrasion-, ozone- and weather-resistant rubber outer layer that survives being dragged over curbs, stored outdoors, and driven over.<\/li>\n<\/ul>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-construction.jpg\" alt=\"Cutaway view of the hose showing the conductive NBR inner tube, textile reinforcement plies, spiral steel wire helix, and abrasion-resistant rubber cover\" class=\"wp-image-4428\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-construction.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-construction-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-construction-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-construction-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 1. The tube-reinforcement-cover assembly; the steel helix is what allows suction service.<\/p>\n\n\n\n<p>Hose construction, layer by layer<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Layer<\/th><th scope=\"col\">Typical material<\/th><th scope=\"col\">Job<\/th><\/tr><\/thead><tbody><tr><td>Tube<\/td><td>Conductive nitrile (NBR)<\/td><td>Carries petrol, diesel and fuel oil without swelling; drains static<\/td><\/tr><tr><td>Reinforcement<\/td><td>Synthetic textile plies + steel wire helix<\/td><td>Carries pressure; stops collapse under vacuum<\/td><\/tr><tr><td>Cover<\/td><td>Oil- and abrasion-resistant rubber, typically chloroprene rubber (CR)<\/td><td>Resists oil splash, abrasion, UV and weather<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>The same vehicle-mounted product family is sold under several names \u2014 tanker truck hose, fuel tanker hose, oil tanker hose \u2014 depending on region and supplier. Petroleum transfer hose is the wider catalogue term that also covers terminal and bulk-loading duty; for that side of the business see our bulk loading and drop hose guide once live, and for the full family range start from our <a href=\"https:\/\/www.henghuahose.com\/fr\/oil-suction-discharge-hose-guide\/\" target=\"_blank\" rel=\"noopener\">oil suction and discharge hose guide<\/a>, which covers the full size and rating range of this family, or see the <a href=\"https:\/\/www.henghuahose.com\/fr\/product\/fuel-suction-discharge-hose\/\" target=\"_blank\" rel=\"noopener\">oil suction and discharge hose<\/a> product page for current sizes and ratings. Naming differs, but construction and ratings follow the same standards, which is why the numbers on the cover matter more than the name on the box.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-tank-truck-vs-fuel-tanker-vs-os-amp-d-hose-what-is-the-difference\">Tank Truck vs Fuel Tanker vs OS&amp;D Hose: What Is the Difference?<\/h2>\n\n\n\n<p>Three names, one hose family: the North American truck-side line, the European fuel-delivery line and the engineering OS&amp;D line share the same helix-reinforced, oil-resistant construction \u2014 the names differ by region, standard and label, not by how the hose is built. Here is the practical difference in one line:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>On-vehicle term, North America:<\/strong> a 150 PSI (10 bar) petroleum hose for truck-side transfer, typically 2 to 4 inch bore, with full vacuum capability, sold as bare hose or as a complete assembly for loading and unloading compartments.<\/li>\n\n\n\n<li><strong>Fuel tanker hose<\/strong> is the European delivery term: the same kind of line carried on fuel trucks that drop petrol and diesel at service stations. In Europe it is specified to EN 1761, which covers both delivery-only and suction-and-delivery hose for liquid fuels.<\/li>\n\n\n\n<li><strong>Oil suction and discharge (OS&amp;D) hose<\/strong> is the engineering name for the wider family: helix-reinforced, full-vacuum hose for bulk petroleum loading at terminals, depots and tankers, specified to EN 1765 or ISO 1823.<\/li>\n<\/ul>\n\n\n\n<p>Three names for one hose family at a glance<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Feature<\/th><th scope=\"col\">On-vehicle hose (US)<\/th><th scope=\"col\">Fuel tanker hose (EN 1761)<\/th><th scope=\"col\">OS&amp;D hose (EN 1765 \/ ISO 1823)<\/th><\/tr><\/thead><tbody><tr><td>Working pressure<\/td><td>150 PSI (10 bar) typical<\/td><td>Up to 10 bar (145 PSI)<\/td><td>10 and 20 bar classes<\/td><\/tr><tr><td>Vacuum rating<\/td><td>Full vacuum with helix<\/td><td>Full vacuum (Type SD)<\/td><td>Full vacuum (0.9 bar)<\/td><\/tr><tr><td>Typical bore<\/td><td>2-4 inch<\/td><td>1-4 inch<\/td><td>3\/4-6 inch<\/td><\/tr><tr><td>Typical standard<\/td><td>US petroleum transfer service, 150 PSI class<\/td><td>EN 1761<\/td><td>EN 1765, ISO 1823, DIN 20023<\/td><\/tr><tr><td>Main job<\/td><td>Loading and unloading tank truck compartments<\/td><td>Fuel truck delivery of petrol and diesel<\/td><td>Terminal, depot and tanker bulk transfer<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>For a fleet buyer the practical message is simple: one construction often carries several of these names and certificates, and a single hose can be tested and marked to more than one standard. A tanker truck hose fitted in Houston and a fuel tanker hose fitted in Hamburg often come off the same production line. Specify the numbers \u2014 bore, working pressure, vacuum, temperature, fluid \u2014 and let the standard follow the application.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-tank-truck-hose-specs-sizes-pressure-vacuum-and-temperature\">Tank Truck Hose Specs: Sizes, Pressure, Vacuum and Temperature<\/h2>\n\n\n\n<p>Four numbers define the product: working pressure, bore, vacuum rating and temperature range \u2014 they are printed on the cover of every compliant hose and they are the numbers a supplier needs to quote correctly. Static safety is the fifth requirement and has its own section below.<\/p>\n\n\n\n<p>Quick specification: typical service class for truck-side petroleum hose<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Specification<\/th><th scope=\"col\">Typical value<\/th><th scope=\"col\">Notes<\/th><\/tr><\/thead><tbody><tr><td>Working pressure<\/td><td>150 PSI (10 bar)<\/td><td>US truck-side class; EN 1761 maximum for fuel truck delivery<\/td><\/tr><tr><td>Minimum burst pressure<\/td><td>600 PSI (4:1 safety factor)<\/td><td>A design margin, never a service value<\/td><\/tr><tr><td>Vacuum rating<\/td><td>Full vacuum (0.9 bar)<\/td><td>Requires the wire helix (Type SD construction)<\/td><\/tr><tr><td>Temperature range<\/td><td>-30 \u00b0C to +80 \u00b0C continuous, +100 \u00b0C peak<\/td><td>Per data sheet; hotter service needs a heat-rated compound<\/td><\/tr><tr><td>Typical bores<\/td><td>2, 3 and 4 inch (DN 50, 75, 100)<\/td><td>3 inch is the workhorse; 4 inch for high-rate duty<\/td><\/tr><tr><td>Tube<\/td><td>Conductive nitrile (NBR)<\/td><td>Drains static end to end<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-psi-rating-should-the-hose-carry\">What PSI Rating Should the Hose Carry?<\/h3>\n\n\n\n<p>Working pressure is the maximum continuous internal pressure at the rated temperature, and for this product family the market standard is 150 PSI (10 bar). The US market is built around the 150 PSI class \u2014 distributor catalogues commonly list 150 PSI as the default for truck-side petroleum transfer \u2014 and European fuel truck hose under EN 1761 is capped at the same 10 bar maximum. The minimum burst pressure is four times working pressure (a 4:1 safety factor), so a 150 PSI hose must burst at not less than 600 PSI; the factor absorbs pressure surges, aging and abrasion damage in service. Our <a href=\"https:\/\/www.henghuahose.com\/fr\/oil-hose-working-pressure-vs-burst-pressure-guide\/\" target=\"_blank\" rel=\"noopener\">oil hose working pressure vs burst pressure guide<\/a> explains why you always select by working pressure, never by burst.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-size-hose-do-we-need-for-multi-compartment-tanker-loading-and-delivery\">What size hose do we need for multi-compartment tanker loading and delivery?<\/h3>\n\n\n\n<p>We run heating oil tankers in the UK and mostly deliver through 2 inch hose \u2014 is that the right size for the job? Size means inside diameter (ID). On trucks, 3 inch is the workhorse for multi-compartment petrol and diesel loading and delivery, while 4 inch is used where the pump or loading arm can move more volume; 2 inch suits fuel oil and heating oil deliveries and smaller compartments. UK heating-oil drops, where the term oil tanker hose is common, are almost always 2 inch. If the 150 PSI rating is the industry default, the bore is the number you actually engineer.<\/p>\n\n\n\n<p>Common sizes for tank truck duty and what each is used for<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Size (ID)<\/th><th scope=\"col\">DN<\/th><th scope=\"col\">Typical job<\/th><th scope=\"col\">Flow at 3 m\/s (planning value)<\/th><\/tr><\/thead><tbody><tr><td>2 inch<\/td><td>DN 50<\/td><td>Fuel oil and heating oil deliveries, small compartments<\/td><td>~21 m\u00b3\/h (95 US gpm)<\/td><\/tr><tr><td>3 inch<\/td><td>DN 75<\/td><td>Multi-compartment petrol and diesel loading and delivery<\/td><td>~48 m\u00b3\/h (210 US gpm)<\/td><\/tr><tr><td>4 inch<\/td><td>DN 100<\/td><td>High-rate terminal loading arms and bulk transfer<\/td><td>~85 m\u00b3\/h (375 US gpm)<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>European orders quote DN (nominal bore in millimetres); US orders quote inches \u2014 they describe the same bore, so DN 50, DN 75 and DN 100 equal 2, 3 and 4 inch. Size from flow and velocity, never from the port you happen to have. A good planning rule for oil service is 1.5-4 m\/s (about 5-13 ft\/s): below 1.5 m\/s sediment settles, above 4 m\/s the hose wears faster and the pump wastes energy. Flow capacity rises with the square of the bore, so going from 3 to 4 inch roughly doubles what the line can move \u2014 that is why a 4 inch hose, not a stronger pump, is usually the fix for a slow loading rate.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg\" alt=\"A road tanker at a fuel depot with its loading arm connected to a 4-inch petroleum hose and a yellow grounding cable visible in daylight\" class=\"wp-image-4427\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 2. Tanker loading pulls vacuum on suction, pushes pressure on discharge, and drags the hose across the yard in between.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-can-the-hose-handle-full-vacuum\">Can the Hose Handle Full Vacuum?<\/h3>\n\n\n\n<p>What happens if a hose without a wire helix is used on the suction side of the pump? It collapses: a delivery-only hose with textile reinforcement but no helix cannot hold the bore open under vacuum. A hose that is built with the wire helix and marked for full vacuum service operates down to about 0.9 bar negative pressure without collapsing. Because the line must pull product out of underground and customer tanks, specify full vacuum on every run that sits on the inlet side of a pump, and confirm it on the data sheet rather than assuming it from the 150 PSI rating.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-temperature-range-does-it-handle\">What Temperature Range Does It Handle?<\/h3>\n\n\n\n<p>For the standard construction in this guide, flexibility is retained to about -30 \u00b0C, with continuous service from -30 \u00b0C to +80 \u00b0C and short peaks up to +100 \u00b0C within the limits stated on the data sheet. The cold end matters for winter fuel oil deliveries \u2014 the hose must stay flexible when the truck operates in freezing conditions; at the hot end, continuous service above +80 \u00b0C needs a heat-rated compound. Check both the coldest ambient temperature where the truck operates and the hottest fluid temperature before ordering \u2014 the printed range is the binding value.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-do-the-hoses-have-to-be-conductive-and-how-do-we-bond-and-ground-during-loading-and-unloading\">Do the hoses have to be conductive, and how do we bond and ground during loading and unloading?<\/h3>\n\n\n\n<p>Yes \u2014 static safety is part of the spec, not an option. Moving petroleum generates static charge, so the tube is conductive and the finished assembly is checked for electrical continuity end to end before shipment. On the vehicle, fleet operators bond the hose ends to the tank and the receiving vessel during transfer, following the site&#8217;s grounding procedure \u2014 the NFPA 385 operating context explained in the standards section below. Ask for the continuity test record with every assembly: the test result is part of the deliverable, not a brochure claim.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-standards-behind-the-marking-en-1761-en-1765-and-nfpa-385\">Standards Behind the Marking: EN 1761, EN 1765 and NFPA 385<\/h2>\n\n\n\n<p>Standards are how a buyer verifies a hose without trusting the supplier&#8217;s word: the standard number on the cover says which tests the hose passed and what its ratings mean. Four documents cover almost every hose of this type on the road.<\/p>\n\n\n\n<p>Standards that apply to this product family<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Standard<\/th><th scope=\"col\">Scope<\/th><th scope=\"col\">When to specify it<\/th><\/tr><\/thead><tbody><tr><td>EN 1761:2025<\/td><td>Rubber hoses and hose assemblies for fuel truck delivery \u2014 two types: delivery (D) and suction-and-delivery (SD), maximum working pressure 10 bar<\/td><td>European fuel trucks delivering petrol and diesel<\/td><\/tr><tr><td>EN 1765:2016<\/td><td>Rubber hose assemblies for oil suction and discharge service for petroleum products, in 10 and 20 bar classes with a 4:1 safety factor<\/td><td>Road tanker, depot and terminal loading and unloading across Europe<\/td><\/tr><tr><td>ISO 1823:2015<\/td><td>International standard for rubber hose and hose assemblies for oil suction and discharge service, with surge-pressure allowance<\/td><td>Export and OEM specifications outside Europe<\/td><\/tr><tr><td>NFPA 385 (2022 edition)<\/td><td>US standard for tank vehicles for flammable and combustible liquids \u2014 vehicle design and operation, including hose mounting, bonding and grounding practice<\/td><td>US fleets and terminals; confirms operating context, not a hose test spec<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>EN 1761 is the standard most buyers mean by &#8220;fuel truck hose&#8221;. The current edition, EN 1761:2025 \u2014 Rubber hoses and hose assemblies for fuel truck delivery \u2014 Specification \u2014 specifies two hose types, Type D (delivery) and Type SD (suction and delivery), for the loading and discharge of liquid hydrocarbon fuels at up to 10 bar working pressure. EN 1765:2016 and its German national relative DIN 20023 cover the wider oil suction and discharge family used for tanker and terminal work; ISO 1823:2015 is the international version of the same spec, often written into export and OEM orders.<\/p>\n\n\n\n<p>What is the difference between EN 1761 Type D and Type SD, and which do we need if our truck only delivers fuel without pulling from underground tanks? Type D is the delivery-only construction: the lighter, lower-cost choice when the hose only ever sits on the pressure side, delivering fuel from the truck to a customer tank. If the same hose also pulls product out of underground or customer tanks, or moves between compartments on the inlet side of the pump, specify Type SD \u2014 its wire helix prevents collapse under suction. When in doubt, choose SD: it covers both duties in one hose, which is why it is the version most fleets standardise on.<\/p>\n\n\n\n<p>&#8220;Our US terminal asks about NFPA 385 \u2014 do we need a special certified hose?&#8221; No: NFPA 385 (2022 edition) regulates the tank vehicle itself \u2014 its design, operation, and bonding and grounding practice during transfer \u2014 not the hose as a tested product, so it is not a hose test standard like EN 1761. Specify the hose to a product standard such as EN 1761 or EN 1765, follow NFPA 385 for vehicle and transfer procedure, and ask your terminal operator which rules apply at their rack.<\/p>\n\n\n\n<p>Read the cover before you install. A compliant hose carries a printed layline that states the standard, the type, the bore and the ratings \u2014 for example &#8220;EN 1761 SD 3 inch 10 bar&#8221; \u2014 plus a date code that tells you the manufacturing period. If the cover marking is missing, faded, or does not state a standard, treat the hose as unverifiable and send it back; the marking is the only proof you have that the ratings are real. In our factory, tank truck hose assemblies are proof-tested and checked for electrical continuity end to end before shipment, and the test record is packed with each assembly.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-tank-truck-hose-assemblies-fittings-ends-and-ordering\">Tank Truck Hose Assemblies: Fittings, Ends and Ordering<\/h2>\n\n\n\n<p>Most buyers do not buy bare hose: they buy a complete assembly \u2014 hose cut to length with factory-fitted end connections, ready to bolt onto the truck. Ordering an assembly correctly removes the most common field failure, which is a coupling fitted on site that pulls out under pressure.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-tank-truck-hose-fittings-are-available\">What Tank Truck Hose Fittings Are Available?<\/h3>\n\n\n\n<p>Three fitting families cover nearly every connection on a truck:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Camlock (cam and groove) couplings<\/strong> are the standard for frequent hook-up because they connect in seconds without tools. They are commonly supplied male or female, and they are the fitting you see on most truck-side hose ends.<\/li>\n\n\n\n<li><strong>Threaded ends<\/strong> \u2014 BSP (British Standard Pipe, parallel thread) and NPT (National Pipe Thread, tapered) \u2014 suit fixed connections to pumps, manifolds and tank outlets. BSP and NPT are not interchangeable: a BSP male will not seal in an NPT female, so match the thread family on both ends and confirm it when you order.<\/li>\n\n\n\n<li><strong>Flanged ends<\/strong> suit large bores and terminal loading arms where the hose bolts to a fixed pipe.<\/li>\n<\/ul>\n\n\n\n<p>Whatever tank truck hose fittings you standardise on, confirm the thread family and pressure rating at both ends. Remember that an assembly is only as strong as its weakest end: in the larger sizes a camlock coupling&#8217;s working pressure can sit at or below the hose rating \u2014 a 4 inch coupling in common carbon steel is commonly rated in the 100-150 PSI band against a 150 PSI hose. Confirm the coupling&#8217;s working pressure and material in the supplier&#8217;s catalogue, and state the required coupling rating on your order \u2014 never assume the fitting is rated to the hose. Our <a href=\"https:\/\/www.henghuahose.com\/fr\/hydraulic-fittings-types-guide\/\" target=\"_blank\" rel=\"noopener\">hydraulic fittings types guide<\/a> explains the thread families in detail.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-assembly.jpg\" alt=\"Factory-crimped 3-inch hose assembly with stainless steel camlock couplings on both ends, coiled on a workshop bench and ready for fitting to a loading arm\" class=\"wp-image-4429\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-assembly.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-assembly-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-assembly-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-assembly-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 3. A complete assembly: hose, crimped ferrules and end fittings, tested as one unit.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-crimped-or-clamped-ends\">Crimped or Clamped Ends?<\/h3>\n\n\n\n<p>For petroleum service, factory-crimped ends are the standard. The ferrule is sized to the hose&#8217;s outside-diameter tolerance and compressed in a controlled cycle, so the crimped joint&#8217;s pull-out strength is verified against the hose&#8217;s own strength \u2014 a correctly crimped end fails by hose rupture, not by the coupling pulling off. Field-attached clamp or reusable couplings are quicker but are the classic source of pull-out failures on suction lines. If you buy bare hose and fit ends yourself, use the coupling manufacturer&#8217;s crimp spec and verify with a pull test on the first assembly of every batch. Distributors catalogue tank truck hose fittings by bore, thread family and pressure class, so quote all three when you order replacements.<\/p>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full\"><img loading=\"lazy\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-crimp-proof-test.jpg\" alt=\"Factory proof test of a crimped tank truck hose assembly: the ferrule pressed on the hose and the assembly on a hydrostatic test bench with pressure gauge\" class=\"wp-image-4430\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-crimp-proof-test.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-crimp-proof-test-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-crimp-proof-test-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-crimp-proof-test-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 4. Factory proof test of a crimped assembly \u2014 ferrule, hose and pressure gauge are verified as one unit before shipment.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-to-specify-when-ordering\">What to Specify When Ordering<\/h3>\n\n\n\n<p>How do I measure and order a replacement assembly with camlock ends so it fits the loading arm the first time? Hand this checklist to any supplier and you will get a comparable quotation on the first pass:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Bore<\/strong> in inches or DN \u2014 2, 3 or 4 inch as a rule.<\/li>\n\n\n\n<li><strong>Working pressure and vacuum<\/strong> \u2014 150 PSI (10 bar) and full vacuum for truck duty.<\/li>\n\n\n\n<li><strong>Fluid and temperature range<\/strong> \u2014 petrol, diesel, fuel oil, and the coldest and hottest service temperatures.<\/li>\n\n\n\n<li><strong>Overall length, end to end<\/strong>, not hose length \u2014 the distance between the two fitting faces.<\/li>\n\n\n\n<li><strong>End fittings at both ends<\/strong>, each stated separately \u2014 for example &#8220;4 inch camlock female both ends&#8221;, or &#8220;3 inch NPT male \u00d7 camlock female&#8221;.<\/li>\n\n\n\n<li><strong>Fitting pressure rating<\/strong> at each end \u2014 state the required working pressure class of the couplings, not just the hose (a 4 inch camlock band is 100-150 PSI in common carbon steel).<\/li>\n\n\n\n<li><strong>Minimum bend radius<\/strong> from the data sheet \u2014 confirm your routing keeps every bend above it, or the helix can fatigue at the kink point.<\/li>\n\n\n\n<li><strong>Standard and marking<\/strong> \u2014 EN 1761, EN 1765, ISO 1823, or the customer&#8217;s spec.<\/li>\n\n\n\n<li><strong>Test documentation<\/strong> \u2014 proof test and continuity records with the shipment.<\/li>\n<\/ul>\n\n\n\n<p>Factory-made assemblies for this duty are typically ordered in lengths from 1 to 20 metres (about 3 to 65 ft), with 3 metre and 6 metre lengths covering most truck-side runs. Confirm the routing on the actual vehicle before ordering: a hose that is too short strains the couplings, and one that is too long drags on the ground.<\/p>\n\n\n\n<p><strong>Have a checklist ready?<\/strong> Send us your bore, length, fittings and quantity \u2014 our engineering team will confirm the specification and quotation the same day. <a href=\"https:\/\/www.henghuahose.com\/fr\/contact\/\" target=\"_blank\" rel=\"noopener\">Contact our team<\/a> and mention &#8220;tanker truck assembly&#8221; with the EN 1761\/1765 standard you need.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-how-long-does-the-hose-last-and-how-to-inspect-it\">How Long Does the Hose Last \u2014 and How to Inspect It<\/h2>\n\n\n\n<p>How long can a delivery hose stay in service, and which signs mean it has to be replaced before the next delivery? A well-built hose of this type normally lasts five to ten years from its date code; hot, sunny climates and ozone-rich locations shorten that. Age alone is not the failure \u2014 abuse is. Dragging the cover over sharp edges, parking with the hose coiled in the sun, and exceeding the working pressure in surges all shorten life, and each leaves a visible trace.<\/p>\n\n\n\n<p>I&#8217;m replacing the delivery hose on our tanker before the winter season \u2014 what inspection signs mean the old one has to go? Inspect on a fixed schedule, not when something leaks. Many fleet operators run a visual check before every shift and a documented proof test every six to twelve months; the exact interval is set by the operator&#8217;s procedure and the fuel company&#8217;s rules. Look for these failure signs and replace the assembly when any of them appears:<\/p>\n\n\n\n<p>Field failure signs in service: what they mean and what to do<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Sign you see<\/th><th scope=\"col\">Most likely cause<\/th><th scope=\"col\">Action<\/th><\/tr><\/thead><tbody><tr><td>Cover cracks, blisters, or cuts to the reinforcement<\/td><td>Ozone, UV, or oil splash on the cover<\/td><td>Replace the assembly; store out of sun and away from motors<\/td><\/tr><tr><td>Flat or kinked section<\/td><td>Helix fatigue, crush, or over-bending in routing<\/td><td>Replace; check the routing and minimum bend radius on the data sheet<\/td><\/tr><tr><td>Coupling loose, corroded, or leaking at the ferrule<\/td><td>Field-fitted end or wrong crimp spec<\/td><td>Replace; use factory crimp spec and pull-test the first of every batch<\/td><\/tr><tr><td>Cover stiff or hose hard to coil<\/td><td>Age or heat exposure<\/td><td>Check the date code; replace if past the five-to-ten-year service band<\/td><\/tr><tr><td>Failed proof test or continuity check<\/td><td>Reinforcement or static-path damage<\/td><td>Take out of service immediately and quarantine<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Store the hose correctly and it lives longer:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Drain it after use, then cap both ends to keep out dirt and water.<\/li>\n\n\n\n<li>Coil it on a tanker truck hose rack or tray, not on the ground.<\/li>\n\n\n\n<li>Keep it out of direct sun and away from ozone sources such as electric motors.<\/li>\n<\/ul>\n\n\n\n<p>Stored indoors out of direct sun, a hose cover typically lasts longest between inspections.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-frequently-asked-questions\">Frequently Asked Questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-psi-is-a-tank-truck-hose-rated-for\">What PSI is a tank truck hose rated for?<\/h3>\n\n\n\n<p>Standard service hose for this duty is rated 150 PSI (10 bar) working pressure, with a minimum burst pressure of 600 PSI at the 4:1 safety factor. European fuel truck hose to EN 1761 is capped at the same 10 bar maximum. Select by working pressure \u2014 never run a hose at its burst rating.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-size-hose-do-i-need-for-tank-truck-duty\">What size hose do I need for tank truck duty?<\/h3>\n\n\n\n<p>Choose by flow and velocity, not by the existing port. 3 inch (DN 75) moves about 48 m\u00b3\/h (210 US gpm) at 3 m\/s and covers most multi-compartment petrol and diesel work; 4 inch (DN 100) roughly doubles that and suits high-rate loading arms; 2 inch (DN 50) suits fuel oil and heating oil deliveries. Keep oil velocity between 1.5 and 4 m\/s.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-can-i-use-a-hydraulic-hose-on-a-tank-truck\">Can I use a hydraulic hose on a tank truck?<\/h3>\n\n\n\n<p>No. A hydraulic hose is built to transmit fluid power at 1,000-6,000 PSI and carries no vacuum rating; this product is a low-pressure, high-flow petroleum hose with a helix for suction. They are different product families, and using one in the other&#8217;s job fails quickly \u2014 see the selection guidance in our how to select hydraulic oil hose article for the boundary.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-how-do-these-names-differ-from-an-oil-transfer-hose\">How do these names differ from an oil transfer hose?<\/h3>\n\n\n\n<p>Fuel tanker hose, oil tanker hose and oil transfer hose describe the same helix-reinforced, oil-resistant petroleum hose family from different angles. The truck-side versions in this guide are the 150 PSI (10 bar) class; the wider oil suction and discharge family also includes a 20 bar class for high-pressure terminal and tanker service (see the comparison table above). Differences between the names are regional \u2014 EN 1761 vs EN 1765 vs ISO 1823 \u2014 and the fittings fitted at the factory. Compare the numbers on the cover, not the name.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-fittings-are-used-on-this-hose\">What fittings are used on this hose?<\/h3>\n\n\n\n<p>Camlock (cam and groove) couplings for frequent hook-up, BSP or NPT threaded ends for fixed pump and tank connections, and flanges for large bores and loading arms. Check the coupling pressure rating \u2014 in 4 inch carbon steel a camlock commonly sits in the 100-150 PSI band, at or below the hose rating \u2014 and match thread families exactly.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-how-often-should-the-hose-be-replaced\">How often should the hose be replaced?<\/h3>\n\n\n\n<p>Replace on failure signs \u2014 cover cracks or blisters, exposed reinforcement, kinked sections, leaking couplings, failed proof tests \u2014 and plan for a five to ten year service life from the date code in normal duty. Shorter in hot, sunny climates. A visual check before every shift and a documented proof test every six to twelve months is common fleet practice; follow your operator&#8217;s procedure and the fuel company&#8217;s rules.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-en-1761-type-d-or-type-sd-which-hose-type-do-i-need\">EN 1761 Type D or Type SD \u2014 which hose type do I need?<\/h3>\n\n\n\n<p>Choose Type SD when the hose will ever sit on the suction side \u2014 pulling fuel from underground or customer tanks \u2014 because its wire helix stops collapse under vacuum. Choose Type D only when the hose is used purely for pressure delivery from the truck. When in doubt, Type SD covers both duties in one hose and is the version most commonly ordered for multi-duty trucks.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-how-should-a-tanker-truck-hose-be-stored-between-shifts\">How should a tanker truck hose be stored between shifts?<\/h3>\n\n\n\n<p>Drain the hose after use, cap both ends, and coil it on a rack or tray out of direct sun and away from ozone sources \u2014 shaded indoor storage is the longest-life option between inspections.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"h-what-is-the-difference-between-a-tanker-truck-hose-and-a-fuel-transfer-hose\">What is the difference between a tanker truck hose and a fuel transfer hose?<\/h3>\n\n\n\n<p>They sit on different sides of the same job. The vehicle-mounted delivery hose is the line that loads and unloads tank compartments \u2014 150 PSI (10 bar), full vacuum, to EN 1761 or EN 1765. Fuel transfer hose is the wider label for hoses that move fuel between tanks and equipment with a pump; some constructions overlap, so the ratings and standards printed on the cover decide fit, not the name.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"h-final-verdict-buy-the-assembly-not-just-the-hose\">Final Verdict: Buy the Assembly, Not Just the Hose<\/h2>\n\n\n\n<p>A tank truck hose is a simple product with a strict spec: 150 PSI (10 bar) working pressure, full vacuum, the right bore for the flow, a temperature range that covers the duty, and a conductive tube for static safety. Match those numbers, confirm the standard on the cover, and buy the hose and fittings as one factory-tested assembly \u2014 that combination removes the two most common failures in the field, wrong fittings and bad crimps.<\/p>\n\n\n\n<p>HENGHUA manufactures complete assemblies in 1 to 4 inch bores to EN 1761, EN 1765 and ISO 1823, in the 150 PSI (10 bar) class with full vacuum, conductive NBR tube and abrasion-resistant cover. Every assembly is crimped in our factory, proof-tested, and continuity-checked before shipment, with camlock, BSP, NPT and flanged ends fitted to your drawing. Send us your checklist \u2014 bore, length, fittings, quantity \u2014 and our engineering team will confirm the specification and quotation the same day. Contact our team to start, or browse the oil hose range for current sizes and ratings.<\/p>\n\n\n\n<p><em>By the HENGHUA Engineering Team \u2014 Senior Hose Application Engineers with 15+ years in industrial hose design and field failure analysis, at a manufacturer with full in-house production, testing, and custom assembly. <\/em><\/p>","protected":false},"excerpt":{"rendered":"<p>A tank truck hose is a flexible, conductive rubber hose assembly that loads and unloads petrol, diesel and fuel oil on and off road tankers \u2014 rated 150 PSI (10 bar) working pressure, full vacuum, in 2 to 4 inch bores, to EN 1761, EN 1765 or ISO 1823. If you are replacing a hose, [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":4427,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_surecart_dashboard_logo_width":"180px","_surecart_dashboard_show_logo":true,"_surecart_dashboard_navigation_orders":true,"_surecart_dashboard_navigation_invoices":true,"_surecart_dashboard_navigation_subscriptions":true,"_surecart_dashboard_navigation_downloads":true,"_surecart_dashboard_navigation_billing":true,"_surecart_dashboard_navigation_account":true,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[1],"tags":[1253,1248,1251,1254,1252],"class_list":["post-4438","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-fuel-tanker-hose","tag-tank-truck-hose","tag-tank-truck-hose-assemblies","tag-tank-truck-hose-fittings","tag-tanker-truck-hose"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v24.5 (Yoast SEO v28.1) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Tank Truck Hose Guide: 150 PSI Specs, Standards &amp; Assemblies<\/title>\n<meta name=\"description\" content=\"Tank truck hose specs, standards and assemblies explained: 150 PSI working pressure, EN 1761, EN 1765 and NFPA 385, and how to order a complete assembly.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.henghuahose.com\/fr\/tank-truck-hose-guide\/\" \/>\n<meta property=\"og:locale\" content=\"fr_FR\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Tank Truck Hose: Specs, Standards &amp; Assemblies\" \/>\n<meta property=\"og:description\" content=\"Tank truck hose specs, standards and assemblies explained: 150 PSI working pressure, EN 1761, EN 1765 and NFPA 385, and how to order a complete assembly.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.henghuahose.com\/fr\/tank-truck-hose-guide\/\" \/>\n<meta property=\"og:site_name\" content=\"HENGHUA\" \/>\n<meta property=\"article:published_time\" content=\"2026-09-08T03:10:10+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-09-08T03:10:13+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"goodheart786@gmail.com\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"goodheart786@gmail.com\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"21 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"TechArticle\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/\"},\"author\":{\"name\":\"goodheart786@gmail.com\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\"},\"headline\":\"Tank Truck Hose: Specs, Standards &#038; Assemblies\",\"datePublished\":\"2026-09-08T03:10:10+00:00\",\"dateModified\":\"2026-09-08T03:10:13+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/\"},\"wordCount\":4216,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/tank-truck-hose-application.jpg\",\"keywords\":[\"fuel tanker hose\",\"tank truck hose\",\"tank truck hose assemblies\",\"tank truck hose fittings\",\"tanker truck hose\"],\"articleSection\":[\"Blog\"],\"inLanguage\":\"fr-FR\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/\",\"name\":\"Tank Truck Hose Guide: 150 PSI Specs, Standards & Assemblies\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/tank-truck-hose-application.jpg\",\"datePublished\":\"2026-09-08T03:10:10+00:00\",\"dateModified\":\"2026-09-08T03:10:13+00:00\",\"description\":\"Tank truck hose specs, standards and assemblies explained: 150 PSI working pressure, EN 1761, EN 1765 and NFPA 385, and how to order a complete assembly.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#breadcrumb\"},\"inLanguage\":\"fr-FR\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"fr-FR\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/tank-truck-hose-application.jpg\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/09\\\/tank-truck-hose-application.jpg\",\"width\":800,\"height\":600,\"caption\":\"A road tanker at a fuel depot with its loading arm connected to a 4-inch petroleum hose and a yellow grounding cable visible in daylight\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/tank-truck-hose-guide\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.henghuahose.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Tank Truck Hose: Specs, Standards &#038; Assemblies\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"name\":\"HENGHUA\",\"description\":\"Powering Your Industry, Worldwide.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"alternateName\":\"HENGHUA Hose\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.henghuahose.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"fr-FR\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\",\"name\":\"HENGHUA\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"fr-FR\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"width\":388,\"height\":90,\"caption\":\"HENGHUA\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\",\"name\":\"goodheart786@gmail.com\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"fr-FR\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"caption\":\"goodheart786@gmail.com\"},\"sameAs\":[\"https:\\\/\\\/henghuahose.com\"],\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/fr\\\/author\\\/goodheart786gmail-com\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Tank Truck Hose Guide: 150 PSI Specs, Standards & Assemblies","description":"Tank truck hose specs, standards and assemblies explained: 150 PSI working pressure, EN 1761, EN 1765 and NFPA 385, and how to order a complete assembly.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.henghuahose.com\/fr\/tank-truck-hose-guide\/","og_locale":"fr_FR","og_type":"article","og_title":"Tank Truck Hose: Specs, Standards & Assemblies","og_description":"Tank truck hose specs, standards and assemblies explained: 150 PSI working pressure, EN 1761, EN 1765 and NFPA 385, and how to order a complete assembly.","og_url":"https:\/\/www.henghuahose.com\/fr\/tank-truck-hose-guide\/","og_site_name":"HENGHUA","article_published_time":"2026-09-08T03:10:10+00:00","article_modified_time":"2026-09-08T03:10:13+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg","type":"image\/jpeg"}],"author":"goodheart786@gmail.com","twitter_card":"summary_large_image","twitter_misc":{"Written by":"goodheart786@gmail.com","Est. reading time":"21 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"TechArticle","@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#article","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/"},"author":{"name":"goodheart786@gmail.com","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7"},"headline":"Tank Truck Hose: Specs, Standards &#038; Assemblies","datePublished":"2026-09-08T03:10:10+00:00","dateModified":"2026-09-08T03:10:13+00:00","mainEntityOfPage":{"@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/"},"wordCount":4216,"commentCount":0,"publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"image":{"@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg","keywords":["fuel tanker hose","tank truck hose","tank truck hose assemblies","tank truck hose fittings","tanker truck hose"],"articleSection":["Blog"],"inLanguage":"fr-FR","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/","url":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/","name":"Tank Truck Hose Guide: 150 PSI Specs, Standards & Assemblies","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#primaryimage"},"image":{"@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg","datePublished":"2026-09-08T03:10:10+00:00","dateModified":"2026-09-08T03:10:13+00:00","description":"Tank truck hose specs, standards and assemblies explained: 150 PSI working pressure, EN 1761, EN 1765 and NFPA 385, and how to order a complete assembly.","breadcrumb":{"@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#breadcrumb"},"inLanguage":"fr-FR","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/"]}]},{"@type":"ImageObject","inLanguage":"fr-FR","@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#primaryimage","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/09\/tank-truck-hose-application.jpg","width":800,"height":600,"caption":"A road tanker at a fuel depot with its loading arm connected to a 4-inch petroleum hose and a yellow grounding cable visible in daylight"},{"@type":"BreadcrumbList","@id":"https:\/\/www.henghuahose.com\/tank-truck-hose-guide\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.henghuahose.com\/"},{"@type":"ListItem","position":2,"name":"Tank Truck Hose: Specs, Standards &#038; Assemblies"}]},{"@type":"WebSite","@id":"https:\/\/www.henghuahose.com\/#website","url":"https:\/\/www.henghuahose.com\/","name":"HENGHUA","description":"Au service de votre secteur d'activit\u00e9, partout dans le monde.","publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"alternateName":"HENGHUA Hose","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.henghuahose.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"fr-FR"},{"@type":"Organization","@id":"https:\/\/www.henghuahose.com\/#organization","name":"HENGHUA","url":"https:\/\/www.henghuahose.com\/","logo":{"@type":"ImageObject","inLanguage":"fr-FR","@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","width":388,"height":90,"caption":"HENGHUA"},"image":{"@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7","name":"goodheart786@gmail.com","image":{"@type":"ImageObject","inLanguage":"fr-FR","@id":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","caption":"goodheart786@gmail.com"},"sameAs":["https:\/\/henghuahose.com"],"url":"https:\/\/www.henghuahose.com\/fr\/author\/goodheart786gmail-com\/"}]}},"_links":{"self":[{"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/posts\/4438","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/comments?post=4438"}],"version-history":[{"count":2,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/posts\/4438\/revisions"}],"predecessor-version":[{"id":4470,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/posts\/4438\/revisions\/4470"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/media\/4427"}],"wp:attachment":[{"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/media?parent=4438"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/categories?post=4438"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.henghuahose.com\/fr\/wp-json\/wp\/v2\/tags?post=4438"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}