SAE O-Ring Male Hydraulic Hose Fitting: 16011/16012 Series (ISO 11926 / SAE J1926)

Why This SAE O-Ring Male Hydraulic Hose Fitting Passes the Compliance Gate
Every SAE O-ring male hydraulic hose fitting in the 16011/16012 family is made to the straight-thread O-ring boss geometry of ISO 11926 and SAE J1926, so it seats squarely on the boss face of standard port blocks, manifolds, pumps and valves. The seal is a captive O-ring pressed between the face of the boss and the fitting, not the threads, which gives repeatable leak-free joints that survive vibration and thermal cycling. For OEMs, distributors and maintenance teams this means fewer specification disputes, simpler inventory control and a drop-in answer for the most common metric-of-inch port sizes in mobile and industrial hydraulics.
Principaux atouts
- O-ring face seal per SAE J1926/ISO 11926 – the sealing element is a groove-mounted O-ring that seals on the flat boss face, independent of thread loading.
- Two hose-tail versions from one head code – order 16011 for braided hose and 16012-XX-XX for spiral hose without changing the thread end.
- Wide dash coverage – thread sizes from 7/16″-20 to 1-5/16″-12 with O-rings O904 through O916, covering -04 to -16 hose.
- Full process traceability – 100% pressure test, thread inspection and batch records on every order.
Caractéristiques techniques
What Is a SAE O-Ring Male Hydraulic Hose Fitting?
A SAE O-ring male hydraulic hose fitting combines a male straight thread (UNF form) with a recessed O-ring groove at the base of the thread. When tightened into a mating boss, the O-ring compresses against the machined face of the boss and becomes the hydraulic seal, while the straight threads only provide mechanical retention. This design is the SAE J1926 / ISO 11926 O-ring boss (ORB) system and must not be confused with JIC 37-degree (SAE J514) or 45-degree flare (SAE J513) cone seals, whose tapered faces are not interchangeable with ORB ports.
To select the right unit, match the thread end to the port, match the O-ring to the thread dash as shown in the table below, then match the hose tail dash to the hose inner diameter you intend to crimp.
Données dimensionnelles
| Symbole | Description |
|---|---|
| E | Male thread outer diameter (thread size), as dimensioned on the drawing |
| A | Overall body length from the front face of the male end to the start of the hose tail |
| C | Length of the threaded portion including the O-ring groove up to the hex shoulder |
| S1 | Hex size of the body (width across flats) for tightening |
Tableau complet des dimensions (matrice des références)
All dimensions are in millimetres. Each part number is built as 16011 - thread dash - hose dash; for example 16011-12-10 means a 1-1/16″-12 thread end (thread dash 12) with a -10 hose tail. Threads are shown as in the original chart and are UNF straight threads (for example 7/16″X20 = 7/16″-20 UNF).
| RÉFÉRENCE. | E THREAD | HOSE BORE DN (mm) | HOSE DASH | O-RING | A (mm) | C (mm) | S1 (mm) |
|---|---|---|---|---|---|---|---|
| 16011-04-04 | 7/16″X20 | 6 | 04 | O904 | 21.5 | 9.1 | 14 |
| 16011-05-04 | 1/2″X20 | 6 | 04 | O905 | 21.5 | 9.1 | 17 |
| 16011-06-05 | 9/16″X18 | 8 | 05 | O906 | 22.5 | 9.9 | 17 |
| 16011-06-06 | 9/16″X18 | 10 | 06 | O906 | 22.5 | 9.9 | 17 |
| 16011-08-06 | 3/4″X16 | 10 | 06 | O908 | 24.5 | 11.1 | 22 |
| 16011-08-08 | 3/4″X16 | 12 | 08 | O908 | 25 | 11.1 | 22 |
| 16011-10-08 | 7/8″X14 | 12 | 08 | O910 | 29.5 | 12.7 | 27 |
| 16011-10-10 | 7/8″X14 | 16 | 10 | O910 | 30.5 | 12.7 | 27 |
| 16011-12-10 | 1.1/16″X12 | 16 | 10 | O912 | 34 | 15.1 | 32 |
| 16011-12-12 | 1.1/16″X12 | 20 | 12 | O912 | 34 | 15.1 | 32 |
| 16011-16-16 | 1.5/16″X12 | 25 | 16 | O916 | 36 | 15.1 | 38 |
Factory note (preserved): the part numbers in this table are for braided hose. If the assembly uses spiral hose, change the code to 16012-XX-XX with the same thread dash and hose dash.
Matériaux et traitements thermiques
| Article | Caractéristiques techniques |
|---|---|
| Matériau | 20#/35#/45# cold-headed carbon steel, or 304/316L stainless on request |
| Traitement thermique | Carburized and quenched, core and surface hardness HRC 20-28 |
| Surface finish | Trivalent zinc (96 h salt spray), zinc-nickel (720 h), or Dacromet (1000 h) |
| Testing | 100% pressure test and 100% thread inspection before despatch |
| Documentation | Material test report (MTR) with order; BV/SGS inspection can be arranged |
Pression de service et plage de fonctionnement
Working pressure is determined jointly by the SAE J1926 port standard and the hose grade you select; HENGHUA does not publish a standalone fitting rating because the crimped assembly is only as strong as its weakest member. Every assembly leaves the factory after a 100% pressure test, and the torque and crimp-diameter data sheet for your hose construction is supplied with the order. Operating temperature is typically -40°C to +120°C, with system de-rating governed by the hose and seal materials in your circuit.
Sélection et commande
Comment lire le tableau des références
Read the part number from left to right: 16011 fixes the ORB head geometry, the first two digits after the dash give the thread dash (04 through 16), and the last two digits give the hose dash (04 through 16). The O-ring code follows the same dash logic – O904 pairs with thread dash 04, O905 with 05, O906 with 06, O908 with 08, O910 with 10, O912 with 12 and O916 with 16 – so you can verify a code is correct before ordering. Because the same head code covers several hose dashes, always state both the port thread and the hose size on your enquiry.
For the port side of the assembly this matrix is the SAE O-ring male hydraulic hose fitting reference, because every thread dash, its O-ring and its hex size are listed for verification before ordering. A SAE O-ring male hydraulic hose fitting bought by code from this table arrives with the O-ring already matched to the thread, which removes a common cause of field leaks. The SAE ORB hose fitting head is shared with the 16012 spiral version, so the port side of your assembly stays identical when you change hose construction.
Thread Size and Dash Chart
| Thread (as drawn) | UNF equivalent | Thread dash | O-ring | Hose dash sizes in this series |
|---|---|---|---|---|
| 7/16″X20 | 7/16″-20 UNF | 04 | O904 | 04 |
| 1/2″X20 | 1/2″-20 UNF | 05 | O905 | 04 |
| 9/16″X18 | 9/16″-18 UNF | 06 | O906 | 05, 06 |
| 3/4″X16 | 3/4″-16 UNF | 08 | O908 | 06, 08 |
| 7/8″X14 | 7/8″-14 UNF | 10 | O910 | 08, 10 |
| 1.1/16″X12 | 1-1/16″-12 UNF | 12 | O912 | 10, 12 |
| 1.5/16″X12 | 1-5/16″-12 UNF | 16 | O916 | 16 |
Service de références croisées
Send us your old part number or a worn sample and our engineers will translate it into the correct 16011 or 16012 code, checking thread form, O-ring dash and hose tail against the drawing before you order. This service is free for OEMs and distributors who order in volume, and it removes the guesswork when you are consolidating legacy inventories onto one crimp system. We never attach another manufacturer’s brand to our parts.
Emballage et logistique
Standard packing is 10 pieces per box with a batch label on every carton; export cartons are marked with the part number, quantity and “Made in China – HENGHUA”. The material test report travels with each shipment, and mixed part numbers can share one container to keep freight economical. For urgent production stops we support split deliveries by air against a confirmed schedule.
Guide de montage et d'utilisation
Procédure de sertissage en quatre étapes
- Cut the hose square – use a sharp saw and a hose cutter, then blow out any debris from the bore.
- Mark the insertion depth – transfer the tail length from the fitting drawing onto the hose cover as a witness mark.
- Lubricate and insert – apply a thin film of assembly lubricant to the tail and push the hose in with a slight twist until it reaches the mark.
- Crimp and verify – crimp with the die set matched to the hose construction, then check the crimped outside diameter with a caliper against the data sheet supplied with the order.
Connecting the O-Ring Boss End
The seal comes from the O-ring against the flat boss face, so keep the straight threads and the port clean before assembly. Lightly coat the O-ring with clean hydraulic oil, run the fitting in by hand until the O-ring touches the boss, then tighten with a wrench on the S1 hex to the SAE J1926 torque values supplied in the accompanying data sheet. Never wind Teflon tape or thread sealant onto the straight threads of a SAE ORB hose fitting – the tape is not the seal, it can stop the O-ring seating, and shredded debris will contaminate the whole circuit.
Avertissements relatifs à l'installation
- ✔ Verify the port is a SAE J1926/ISO 11926 boss with a flat, undamaged face before assembly.
- ✔ Lubricate the O-ring with hydraulic oil only, never grease that is incompatible with the seal.
- ✔ Use a torque wrench; the correct value is given on the order-specific data sheet.
- ❌ Do not use Teflon tape, anaerobic sealant or pipe dope on the straight threads.
- ❌ Do not mix this ORB end with JIC 37-degree (SAE J514) or 45-degree flare (SAE J513) ports – the sealing systems are different and cannot seal against each other.
- ❌ Do not use a 16011 braided-hose code on a spiral hose assembly; select 16012-XX-XX instead.
Personnalisation OEM et traçabilité de la qualité
Options de personnalisation
We offer OEM and private-label programs including laser marking of your part number and logo, custom plating and colour, special thread tolerances and modified tail lengths for unusual hose covers. Send a drawing or a sample and our team will quote tooling and lead time within 24 hours.
Système de qualité et de traçabilité
Every heat and batch is tracked from cold heading through machining, heat treatment, plating and final test, so a batch number traces back to the material certificate. Pressure testing is 100% rather than sample-based, and the MTR is included with the order; BV or SGS witness inspection can be arranged on request.
FAQ
1. What is the difference between 16011 and 16012 part numbers? The thread end and O-ring are identical; only the hose tail changes. 16011 codes are machined for braided hose, while 16012-XX-XX is the same head for spiral hose assemblies.
2. Do ORB straight threads need Teflon tape? No. The O-ring is the seal and the straight threads only hold the fitting. Tape or sealant can prevent the O-ring from seating and its debris will contaminate the system. For a SAE O-ring male hydraulic hose fitting of any size in this series, clean threads and a lightly lubricated ring are all the sealing preparation you need.
3. What standard is this fitting made to? The O-ring boss head follows SAE J1926 and ISO 11926, using UNF straight threads and an O-ring face seal with an O904 to O916 series ring matched to the thread dash. Both 16011 and 16012 are SAE ORB hose fittings with the same head geometry, so the port side never changes when you switch from braided to spiral hose.
4. Can I connect this fitting to a JIC or flare port? No. JIC 37-degree (SAE J514), 45-degree flare (SAE J513) and ORB (SAE J1926/ISO 11926) are different sealing systems and their mating parts are not interchangeable.
5. Which O-ring comes with the fitting? Each code is supplied with the ring listed in the table, for example O908 for a 3/4″-16 thread end. Tell us your fluid type and temperature and we will confirm the seal compound is compatible.
6. What pressure is this fitting rated for? Working pressure is set by the SAE J1926 port standard together with your hose grade; the finished assembly is 100% pressure tested and the torque and crimp data sheet accompanies your order.
7. Can I get the fittings laser-marked with our own part number? Yes. OEM marking, custom plating and packaging are standard services; send the artwork and we will confirm within 24 hours.
Demander un devis
Send us the part number or the thread and hose dash sizes, the hose construction you crimp, the quantity and your target delivery date. Our engineers reply within 24 hours with a price, lead time and the matching torque and crimp data sheet, and samples are available for evaluation before volume orders. Email your enquiry to the HENGHUA sales team and ask for the SAE O-ring male hydraulic hose fitting quotation.
Parcourir l'intégralité de Raccords hydrauliques SAE une gamme pour toute la famille, ou nous contacter pour demander un devis, des rapports d'essais d'usine et des échantillons.
Demande de renseignements sur nos produits
Nous sommes un fournisseur mondial de raccords et d'équipements hydrauliques, au service d'un large éventail de secteurs grâce à une solution d'approvisionnement « tout-en-un ». Nos produits comprennent : flexibles hydrauliques, raccords, adaptateurs, raccords rapides, connecteurs, protections de flexibles, équipements hydrauliques et bien plus encore : tout ce dont vous avez besoin pour assurer le bon déroulement et l'efficacité de vos opérations.
Faites-nous part de vos besoins à l'aide du formulaire ci-dessous. Notre équipe vous répondra en vous proposant des conseils d'experts et un devis sur mesure afin d'assurer le bon déroulement de vos activités.
- Tuyau hydraulique2323 produits
- Tuyau hydraulique à spirale en fil d'acier66 produits
- Tuyau hydraulique tressé en fil d’acier1010 produits
- Tuyau hydraulique renforcé de tissu33 produits
- Tuyau hydraulique thermoplastique33 produits
- Tuyau industriel7575 produits
- Tuyau à air99 produits
- Tuyau d'arrosage1111 produits
- Tuyau d'huile1616 produits
- Tuyau pour produits chimiques66 produits
- Tuyau composite1616 produits
- Tuyau composite chimique33 produits
- Tuyau composite marin55 produits
- Tuyau composite pour le pétrole55 produits
- Tuyau composite résistant aux hautes températures11 produit
- Tuyau composite en PTFE11 produit
- Tuyau composite cryogénique11 produit
- Tuyau à vapeur33 produits
- Tuyau polyvalent22 produits
- Tuyaux pour l'agroalimentaire44 produits
- Tuyau pour béton44 produits
- Tuyau à ciment22 produits
- Tuyau pour la manutention de matériaux1111 produits
- Tuyau de dragage44 produits
- Raccords hydrauliques166166 produits
- Raccords de tuyaux réutilisables66 produits
- Raccords de tuyau sans emboîtement88 produits
- Raccords hydrauliques JIC1616 produits
- Raccords hydrauliques métriques4141 produits
- Raccords hydrauliques NPT66 produits
- Raccords hydrauliques BSP2626 produits
- Raccords hydrauliques SAE3030 produits
- Raccords hydrauliques de type « banjo »44 produits
- Raccords hydrauliques ORFS1111 produits
- Embout1111 produits
- Raccords à bride2626 produits
- Raccords monoblocs2424 produits
- Adaptateurs hydrauliques149149 produits




