One-Piece SAE Flange 3000 PSI Code 61 Hydraulic Hose Fitting: 87311-RW Series

Why This One-Piece SAE Flange Fitting Passes the Compliance Gate

This one-piece SAE flange fitting is the straight version of the HENGHUA 87311-RW family, built to the specification sheet title “SAE FLANGE 3000 PSI (ISO 12151-3, SAE J516)”. The flange head follows the SAE J518 / ISO 6162-1 Code 61 (3000 psi) dimension system, so it bolts straight onto Code 61 pads on pumps, motors, valves and manifolds.

For OEMs it simplifies hose-assembly quoting because one part number covers flange and hose end. For distributors it keeps slow movers low, because one series spans flange sizes from 1/2″ to 2.1/2″. For maintenance teams it removes the guessing game between braided and spiral hose ends, because the chart note states the rule in plain terms.

• Straight (0 degree) geometry for direct run connections
• Flange sizes 1/2″ to 2.1/2″ per the dimension chart
• Hose bores DN 12 to DN 64, dash -08 to -40
• Series note: listed part numbers are for braided hoses; spiral hose versions use the 87312-XX-XXRW series
• 100% pressure tested, batch traceable, Made in China by the HENGHUA factory

Core Advantages

1. 3000 psi Code 61 flange head. The SAE flange hydraulic hose fitting end mates with SAE J518 / ISO 6162-1 Code 61 flanges. A code 61 flange fitting is the default choice for most 3000 psi circuits in mobile and industrial hydraulics, and the SAE 3000 psi flange head pattern is shared across all sizes in this series.
2. One-piece monobloc body. A one-piece SAE flange fitting has no loose collar or separable ring to lose on the job site, which speeds up assembly and keeps fitting inventory simple.
3. Wide size coverage in one series. Fifteen standard part numbers cover flange 1/2″ to 2.1/2″ with hose dash -08 through -40, so one series book covers most Code 61 straight runs.
4. Braided and spiral twins. Keep the same flange geometry and switch to the 87312-XX-XXRW series when the hose construction is spiral.
5. Corrosion control options. Trivalent zinc, zinc-nickel or Dacromet surface finish selected by environment, with stainless steel available on request.

Technical Specifications

What Is a One-Piece SAE Flange Fitting?

A flange type hydraulic hose fitting connects a hose end to a flanged port instead of a threaded one. The flange head on this fitting matches the Code 61 pad pattern, and the hose end is crimped onto the hose in one permanent operation. One-piece construction means the flange head, neck and hose-end body are machined from a single blank, with no separately assembled flange head or loose parts.

When you compare code 61 vs code 62 flange fittings, remember that Code 61 is the 3000 psi series and Code 62 is the 6000 psi series. The 87311-RW is dimensioned for Code 61 (SAE J518 / ISO 6162-1) pads, and the hose-end interface follows ISO 12151-3, which is the standard behind the SAE J516 designation printed on the spec sheet.

Dimensional Data

The dimension letters below are printed on the specification drawing and used as column headers in the matrix. All values are in millimetres.

Full Dimension Table (Part Number Matrix)

Read a part number as series – flange dash – hose dash. Flange dash and hose dash both count in 1/16 inch steps. Example: 87311-32-24RW means series 87311-RW, flange 2″ (-32), hose -24 (1.1/2″, DN 40). The “RW” suffix marks this one-piece crimp series for braided hoses. Dimensions A, C, D and L increase with flange size exactly as printed on the chart.

Hose Series: Braided and Spiral Versions

The chart note on the specification sheet is the buying rule. Note 1: the part numbers in the table are for braided hoses. Note 2: if the hose is spiral, change the part number to 87312-XX-XXRW. The flange head geometry stays on the same Code 61 pad, but the hose-end body is different because spiral hose constructions need a different crimp profile.

When you order, tell us the hose brand, hose bore and working pressure so we can confirm the correct series and crimp data sheet.

Matériaux et traitements thermiques

Working Pressure and Operating Envelope

The 3000 psi class does not mean every size runs at 3000 psi. The pressure capability of a finished assembly is the lowest rating among hose, fitting and flange size, so confirm the size-dependent rating on the standard table or our data sheet before design release. SAE 3000 psi flange fittings are graded per flange size, so always match the part number to the pad rating. If the application is an excavator, loader or industrial power unit, tell us the machine and circuit, and we will confirm which code 61 flange fitting size applies.

Selection and Ordering

How to Read the Part Number Matrix

• Segment 1 is the series: 87311-RW for straight one-piece flange fittings on braided hose.
• Segment 2 is the flange dash, equal to the Code 61 flange size in 1/16 inch increments: 08 = 1/2″, 12 = 3/4″, 16 = 1″, 20 = 1.1/4″, 24 = 1.1/2″, 32 = 2″, 40 = 2.1/2″.
• Segment 3 is the hose dash in 1/16 inch increments: 08 = DN 12, 10 = DN 16, 12 = DN 20, 16 = DN 25, 20 = DN 32, 24 = DN 40, 32 = DN 50, 40 = DN 64.
• The RW suffix identifies the one-piece crimp series; it does not change the flange dimension logic.

Check your selection against the table above before ordering. A wrong flange dash will not bolt to the Code 61 pad, and a wrong hose dash will not crimp cleanly.

Flange Size and Dash Size Chart

Cross Reference Service

Do you have a legacy or OEM part number from an old machine and no drawing? Send us the number, a photo and the basic dimensions. We match flange size, hose dash and overall length against the 87311-RW matrix and reply with a cross reference proposal within 24 hours. The service is free, and samples can be shipped worldwide for verification.

Emballage et logistique

Assembly and Use Guide

Four-Step Crimping Procedure

1. Cut the hose square with a sharp blade; a vertical cut protects the wire layer.
2. Mark the insertion depth shown on the HENGHUA crimp data sheet supplied with every order.
3. Apply assembly lubricant and push the hose onto the fitting up to the depth mark.
4. Crimp in one continuous stroke, then verify the crimp outside diameter with a caliper against the data sheet value.

Never guess the crimp outside diameter. Every order ships with its crimp data sheet, and the value is specific to hose brand and construction.

Mounting the Flange Connection

• Face the flange head squarely onto the Code 61 pad and check the O-ring groove is clean.
• Fit the O-ring for the flange size; the O-ring is the seal, so replace it whenever the joint is opened.
• Bring the flange together evenly and tighten the bolts in a diagonal sequence.
• Apply the torque value from the flange data sheet; do not rely on feel.

Installation Warnings

• Do not mix hose, fitting or ferrule components from different sources; parts are released as a matched set.
• Do not use a braided-hose fitting on a spiral hose, and never swap 87311-RW parts into a spiral assembly; order the 87312-XX-XXRW series instead.
• Flange bolts and O-rings are not part of the fitting; order them to the flange size separately.
• Crimping is a one-way operation. A one-piece SAE flange fitting cannot be re-crimped after a failed first attempt, so verify the setup before pulling the trigger.
• Do not reuse a fitting pulled from an old hose assembly; the crimp zone has already yielded.
• If the assembly leaks at the flange face, stop and check the O-ring, the bolt torque and the pad surface before tightening further.

OEM Customization and Quality Traceability

Customization Options

• Custom hose-end and dash combinations within the Code 61 flange range
• Surface finish choice: trivalent zinc, zinc-nickel or Dacromet for the environment
• Laser marking of customer logo, part number and batch code
• Stainless steel material option in 304 or 316L
• Custom packaging and export documentation per OEM requirement

Quality and Traceability System

Every fitting moves through incoming material check, cold heading or forging, machining, heat treatment, surface finishing, 100% dimensional inspection, 100% pressure test, marking and packaging. The batch number on the box links back to the material heat number, heat treatment records and inspection reports, so any field question can be answered with documents instead of opinions. Third-party inspection by BV or SGS can be arranged before shipment.

FAQ

1. What standard is the 87311-RW one-piece SAE flange fitting made to? The hose-end dimensions follow ISO 12151-3 / SAE J516 as printed on the spec sheet title, and the flange head follows the SAE J518 / ISO 6162-1 Code 61 system, which is the 3000 psi series.

2. What pressure rating does this SAE flange hydraulic hose fitting carry? This SAE flange hydraulic hose fitting is built to the 3000 psi Code 61 class. The finished assembly pressure depends on the hose rating and the flange size, so confirm the size-dependent rating and the crimp data sheet before production.

3. Can I use this one-piece SAE flange fitting with spiral hose? No. The chart note says the listed part numbers are for braided hoses. For spiral hose, order the 87312-XX-XXRW series, which keeps the same Code 61 flange head.

4. Which flange and hose sizes are available? Flange sizes run from 1/2″ to 2.1/2″ and hose bores from DN 12 to DN 64 (dash -08 to -40). The full dimension table lists all fifteen standard combinations. The table covers the full SAE 3000 psi flange size range available in this series.

5. How do I identify the size I need? Read the part number as series – flange dash – hose dash. For example, 87311-32-24RW means flange 2″ and hose -24. Both dashes are 1/16 inch increments. Every code 61 flange fitting number in the series follows the same logic.

6. What is the advantage of a one-piece design? There is no loose flange head or collar to assemble and no separate part to lose. The one-piece body is machined from a single blank, which simplifies handling and keeps the flange face square to the hose end.

7. Are flange bolts and O-rings included? They are not part of the fitting. Order bolts and O-rings to the Code 61 flange size separately, and use the torque value from the flange data sheet.

8. How fast can I get a quotation and samples? Quotations are answered within 24 hours with the full technical data sheet. Samples can be shipped worldwide for fit testing before series orders.

Demander un devis

Send us the hose type, flange size and dash size, or simply your legacy part number. Tell us the quantity, surface finish and whether stainless steel is required, and our engineers will confirm the correct 87311-RW part number with drawings and the crimp data sheet. OEM inquiries for custom one-piece SAE flange fittings and private label marking are welcome. Expect a reply within 24 hours and sample support before you commit to a series order.

Browse the full Raccords à bride range for the complete family, or contact us to request a quote, mill test reports, and samples.