45 Degree Elbow One-Piece SAE Flange 3000 PSI Code 61 Hydraulic Hose Fitting: 87341-RW Series

]

Why This 45 Degree Elbow One-Piece SAE Flange Fitting Passes the Compliance Gate

This 45 degree elbow one-piece SAE flange fitting is the 45 degree version of the HENGHUA 87341-RW family, built to the specification sheet title “45 DEGREE ELBOW SAE FLANGE 3000 PSI (ISO 12151-3, SAE J516)”. The flange head follows the SAE J518 / ISO 6162-1 Code 61 (3000 psi) dimension system, so it bolts straight onto Code 61 pads while the hose runs away at 45 degrees.

For OEMs it opens routing options in tight valve and manifold bays without extra adapters. For distributors it is a compact stock-keeping unit, because thirteen standard part numbers cover flange sizes from 1/2″ to 2″. For maintenance teams the 45 degree angle reduces hose bending stress compared with a forced 90 degree turn, which extends hose life on vibrating machines.

• 45 degree elbow geometry with a Code 61 flange head
• Flange sizes 1/2″ to 2″ per the dimension chart
• Hose bores DN 12 to DN 50, dash -08 to -32
• Series note: listed part numbers are for braided hoses; spiral hose versions use the 87342-XX-XXRW series
• 100% pressure tested, batch traceable, Made in China by the HENGHUA factory

Core Advantages

1. 3000 psi Code 61 flange head. The flange end mates with SAE J518 / ISO 6162-1 Code 61 pads. A code 61 flange fitting is the default choice for most 3000 psi circuits in mobile and industrial hydraulics, and the SAE 3000 psi flange head pattern is shared across all sizes in this series.
2. 45 degree routing without adapters. A 45 degree SAE flange fitting swings the hose around obstacles with less hose strain than a 90 degree bend, so hose length and bend radius stay manageable.
3. One-piece monobloc body. This one-piece SAE flange fitting has no loose flange head or collar, which cuts assembly time and removes a whole class of leak points.
4. Braided and spiral twins. Keep the same flange geometry and switch to the 87342-XX-XXRW series when the hose construction is spiral.
5. Corrosion control options. Trivalent zinc, zinc-nickel or Dacromet surface finish selected by environment, with stainless steel available on request.

Technical Specifications

What Is a 45 Degree Elbow One-Piece SAE Flange Fitting?

A flange type hydraulic hose fitting connects a hose end to a flanged port instead of a threaded one. This version turns the flow direction by 45 degrees between the flange head and the hose end, which is the standard angle for routing hose away from pumps and motors that sit close to structure. One-piece construction means the flange head, elbow and hose-end body are machined from a single blank.

When you compare code 61 vs code 62 flange fittings, remember that Code 61 is the 3000 psi series and Code 62 is the 6000 psi series. The 87341-RW is dimensioned for Code 61 (SAE J518 / ISO 6162-1) pads, and the hose-end interface follows ISO 12151-3, the standard behind the SAE J516 designation printed on the spec sheet.

Dimensional Data

The dimension letters below are printed on the specification drawing and used as column headers in the matrix. All values are in millimetres.

Full Dimension Table (Part Number Matrix)

Read a part number as series – flange dash – hose dash. Flange dash and hose dash both count in 1/16 inch steps. Example: 87341-32-32RW means series 87341-RW, flange 2″ (-32), hose -32 (2″, DN 50). The “RW” suffix marks this one-piece crimp series for braided hoses. Dimensions A, C, D, H and L increase with flange size exactly as printed on the chart.

Hose Series: Braided and Spiral Versions

The chart note on the specification sheet is the buying rule. Note 1: for use with braided hoses. Note 2: if use with spiral hoses, the hose fitting series number is 87342-XX-XXRW. The flange head geometry stays on the same Code 61 pad, but the hose-end body is different because spiral hose constructions need a different crimp profile.

When you order, tell us the hose brand, hose bore and working pressure so we can confirm the correct series and crimp data sheet.

Matériaux et traitements thermiques

Working Pressure and Operating Envelope

The 3000 psi class does not mean every size runs at 3000 psi. The pressure capability of a finished assembly is the lowest rating among hose, fitting and flange size, so confirm the size-dependent rating on the standard table or our data sheet before design release. SAE 3000 psi flange fittings are graded per flange size, so always match the part number to the pad rating. If the application is an excavator, loader or industrial power unit, tell us the machine and circuit, and we will confirm which code 61 flange fitting size applies.

Selection and Ordering

How to Read the Part Number Matrix

• Segment 1 is the series: 87341-RW for 45 degree elbow one-piece flange fittings on braided hose.
• Segment 2 is the flange dash, equal to the Code 61 flange size in 1/16 inch increments: 08 = 1/2″, 12 = 3/4″, 16 = 1″, 20 = 1.1/4″, 24 = 1.1/2″, 32 = 2″.
• Segment 3 is the hose dash in 1/16 inch increments: 08 = DN 12, 10 = DN 16, 12 = DN 20, 16 = DN 25, 20 = DN 32, 24 = DN 40, 32 = DN 50.
• The RW suffix identifies the one-piece crimp series; it does not change the flange dimension logic.

Check your selection against the table above before ordering. A wrong flange dash will not bolt to the Code 61 pad, and a wrong hose dash will not crimp cleanly.

Flange Size and Dash Size Chart

Cross Reference Service

Do you have a legacy or OEM part number from an old machine and no drawing? Send us the number, a photo and the basic dimensions. We match flange size, hose dash and the A and H elbow dimensions against the 87341-RW matrix and reply with a cross reference proposal within 24 hours. The service is free, and samples can be shipped worldwide for verification.

Emballage et logistique

Assembly and Use Guide

Four-Step Crimping Procedure

1. Cut the hose square with a sharp blade; a vertical cut protects the wire layer.
2. Mark the insertion depth shown on the HENGHUA crimp data sheet supplied with every order.
3. Apply assembly lubricant and push the hose onto the fitting up to the depth mark.
4. Crimp in one continuous stroke, then verify the crimp outside diameter with a caliper against the data sheet value.

Never guess the crimp outside diameter. Every order ships with its crimp data sheet, and the value is specific to hose brand and construction.

Mounting the Flange Connection

• Face the flange head squarely onto the Code 61 pad and check the O-ring groove is clean.
• Fit the O-ring for the flange size; the O-ring is the seal, so replace it whenever the joint is opened.
• Confirm the 45 degree outlet direction is aimed at the hose route before you tighten.
• Bring the flange together evenly and tighten the bolts in a diagonal sequence.
• Apply the torque value from the flange data sheet; do not rely on feel.

Installation Warnings

• Do not mix hose, fitting or ferrule components from different sources; parts are released as a matched set.
• Do not use a braided-hose fitting on a spiral hose, and never swap 87341-RW parts into a spiral assembly; order the 87342-XX-XXRW series instead.
• Flange bolts and O-rings are not part of the fitting; order them to the flange size separately.
• Crimping is a one-way operation. A one-piece SAE flange fitting cannot be re-crimped after a failed first attempt, so verify the setup before pulling the trigger.
• Do not reuse a fitting pulled from an old hose assembly; the crimp zone has already yielded.
• Check that the 45 degree outlet does not clash with adjacent lines when the flange is torqued; rotate the fitting before final bolt-up if it does.

OEM Customization and Quality Traceability

Customization Options

• Custom hose-end and dash combinations within the Code 61 flange range
• Surface finish choice: trivalent zinc, zinc-nickel or Dacromet for the environment
• Laser marking of customer logo, part number and batch code
• Stainless steel material option in 304 or 316L
• Custom packaging and export documentation per OEM requirement

Quality and Traceability System

Every fitting moves through incoming material check, cold heading or forging, machining, heat treatment, surface finishing, 100% dimensional inspection, 100% pressure test, marking and packaging. The batch number on the box links back to the material heat number, heat treatment records and inspection reports, so any field question can be answered with documents instead of opinions. Third-party inspection by BV or SGS can be arranged before shipment.

FAQ

1. What standard is the 87341-RW 45 degree elbow one-piece SAE flange fitting made to? The hose-end dimensions follow ISO 12151-3 / SAE J516 as printed on the spec sheet title, and the flange head follows the SAE J518 / ISO 6162-1 Code 61 system, which is the 3000 psi series.

2. Why choose a 45 degree SAE flange fitting instead of a straight or 90 degree version? The 45 degree outlet lets the hose leave the flange at a shallow angle, which keeps the bend radius generous in tight compartments. It is the common choice for pump and motor ports where a straight fitting would force the hose into a hard bend. In short, a 45 degree SAE flange fitting is the routing answer between a straight run and a full 90 degree turn.

3. What pressure rating does this SAE flange hydraulic hose fitting carry? This 45 degree SAE flange fitting carries the 3000 psi Code 61 class rating. The finished assembly pressure depends on the hose rating and the flange size, so confirm the size-dependent rating and the crimp data sheet before production.

4. Can I use this one-piece SAE flange fitting with spiral hose? No. The chart note says the listed part numbers are for braided hoses. For spiral hose, order the 87342-XX-XXRW series, which keeps the same Code 61 flange head and 45 degree geometry.

5. Which flange and hose sizes are available? Flange sizes run from 1/2″ to 2″ and hose bores from DN 12 to DN 50 (dash -08 to -32). The full dimension table lists all thirteen standard combinations with A, C, D, H and L values. The table covers the full SAE 3000 psi flange size range available in this series. Every code 61 flange fitting size in the table follows the same part number logic.

6. How do I identify the size I need? Read the part number as series – flange dash – hose dash. For example, 87341-32-24RW means flange 2″ and hose -24. Both dashes are 1/16 inch increments, and the H column gives the elbow drop height for routing checks.

7. Are flange bolts and O-rings included? They are not part of the fitting. Order bolts and O-rings to the Code 61 flange size separately, and use the torque value from the flange data sheet.

8. How fast can I get a quotation and samples? Quotations are answered within 24 hours with the full technical data sheet. Samples can be shipped worldwide for fit testing before series orders.

Demander un devis

Send us the hose type, flange size and dash size, or simply your legacy part number. Tell us the quantity, surface finish and whether stainless steel is required, and our engineers will confirm the correct 87341-RW part number with drawings and the crimp data sheet. OEM inquiries for custom 45 degree one-piece SAE flange fittings and private label marking are welcome. Expect a reply within 24 hours and sample support before you commit to a series order.

Browse the full Raccords à bride range for the complete family, or contact us to request a quote, mill test reports, and samples.