{"id":6476,"date":"2026-10-19T01:45:25","date_gmt":"2026-10-19T01:45:25","guid":{"rendered":"https:\/\/www.henghuahose.com\/?p=6476"},"modified":"2026-10-19T01:45:28","modified_gmt":"2026-10-19T01:45:28","slug":"steel-wire-reinforced-steam-hose","status":"publish","type":"post","link":"https:\/\/www.henghuahose.com\/de\/steel-wire-reinforced-steam-hose\/","title":{"rendered":"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings"},"content":{"rendered":"<p>A steel wire reinforced steam hose is specified by its inside diameter, outside diameter, tolerance, bend radius, unit weight, working pressure, and burst pressure. Reading those fields in the right order prevents the most common sizing error on a steam line. ISO 6134 rates this construction as Type 2, the high-pressure type, at 1.8 MPa and 210 \u00b0C.<\/p>\n\n\n\n<p>This guide explains how each specification column is defined, how the two pressure figures are read together, and why an assembled hose can be rated below the hose body. Every pressure and temperature pair here comes from ISO 6134 or a published saturated steam table.<\/p>\n\n\n\n<p><em>About a 14-minute read at 250 words per minute; how to read a steel wire reinforced steam hose datasheet and its pressure rating chart.<\/em><\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-a-steel-wire-reinforced-steam-hose-datasheet-must-show\">What a Steel Wire Reinforced Steam Hose Datasheet Must Show<\/h2>\n\n\n\n<p>A steel wire reinforced steam hose datasheet is a controlled document, not a marketing page. Every column answers one field question: does this hose fit, bend, and hold the rated steam condition? Missing columns force the buyer to guess.<\/p>\n\n\n\n<p>Steam duty punishes a loose specification. A saturated steam line holds a fixed pressure and temperature pair, so the hose, the coupling, and the support must agree on the same pair. The datasheet is where that agreement is recorded. A complete sheet lets a buyer compare two suppliers on facts instead of adjectives.<\/p>\n\n\n\n<p>Read the sheet from the inside out. Start with the bore and the wall, then the bend radius and the unit weight, and finish with the pressure block. That order matches how the hose is built, how it is routed, and how it fails. Use the <a href=\"https:\/\/www.henghuahose.com\/de\/hose-size-selection-guide\/\" target=\"_blank\" rel=\"noopener\">hose size selection guide<\/a> when the bore is still open.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-id-od-bend-radius-callout.jpg\" alt=\"cutaway of a steel wire reinforced steam hose with inside diameter, outside diameter and bend radius callouts\" class=\"wp-image-6442\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-id-od-bend-radius-callout.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-id-od-bend-radius-callout-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-id-od-bend-radius-callout-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-id-od-bend-radius-callout-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-id-od-bend-radius-callout-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 1. Dimension callouts on a steel wire reinforced steam hose, from inside diameter and outside diameter to the minimum bend radius.<\/p>\n\n\n\n<p>Seven columns carry almost all of the meaning on a steam hose datasheet. Table 1 lists them in reading order and shows the consequence of ignoring each one.<\/p>\n\n\n\n<p>Table 1. Seven specification columns on a steam hose datasheet, in reading order.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Specification column<\/th><th scope=\"col\">What it fixes<\/th><th scope=\"col\">Consequence if it is ignored<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Inside diameter<\/th><td>Flow area and coupling size<\/td><td>Pressure drop or a poor fit<\/td><\/tr><tr><th scope=\"row\">Au\u00dfendurchmesser<\/th><td>Clearance against clamps and guards<\/td><td>The hose will not seat or route<\/td><\/tr><tr><th scope=\"row\">ID tolerance<\/th><td>Fit against the coupling tail<\/td><td>Weeping or a loose joint<\/td><\/tr><tr><th scope=\"row\">Bend radius<\/th><td>Routing and support spacing<\/td><td>Kinking and early fatigue<\/td><\/tr><tr><th scope=\"row\">Weight per unit length<\/th><td>Load on hangers and handling effort<\/td><td>Sagging or overloaded supports<\/td><\/tr><tr><th scope=\"row\">Betriebsdruck<\/th><td>The continuous service limit<\/td><td>Operation above the safe rating<\/td><\/tr><tr><th scope=\"row\">Burst rating<\/th><td>Evidence of the safety margin<\/td><td>No proof of reserve strength<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>A datasheet that omits the tolerance or the unit weight is not finished. Those two columns decide whether the hose seals and whether it stays up. Treat their absence as a question for the supplier, not as a detail you can fill in later.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"inside-diameter-outside-diameter-and-tolerance\">Inside Diameter, Outside Diameter, and Tolerance<\/h2>\n\n\n\n<p>Three numbers define the fit of a steam hose: inside diameter, outside diameter, and ID tolerance. Inside diameter sets the flow area and the coupling size. It is the number most buyers quote, and it is only part of the story.<\/p>\n\n\n\n<p>Outside diameter sets the clearance against clamps, guards, and insulation. It also decides how the hose sits in a tray or on a support. A hose that fits the coupling but not the guard still will not install, so order both numbers together.<\/p>\n\n\n\n<p>ID tolerance is the allowed variation of the bore around its nominal size. A coupling tail is machined to a nominal bore plus a small window. When the hose bore and the tail both sit near their limits, the assembly can weep or fail to seal. Tolerance is therefore a fit specification, not a cosmetic one.<\/p>\n\n\n\n<p>Most steam hoses are quoted in millimeters and in inches, because different markets read different units. Convert before you compare, not after you order. A quick millimeter to inch conversion chart removes the guesswork from a cross-border specification.<\/p>\n\n\n\n<p>Table 2. Inside diameter, outside diameter, and tolerance on a steam hose datasheet.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Term<\/th><th scope=\"col\">Measured across<\/th><th scope=\"col\">Unit<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Inside diameter<\/th><td>The bore the steam contacts<\/td><td>Millimeters or inches<\/td><\/tr><tr><th scope=\"row\">Au\u00dfendurchmesser<\/th><td>The cover, one outer face to the other<\/td><td>Millimeters or inches<\/td><\/tr><tr><th scope=\"row\">ID tolerance<\/th><td>Allowed variation of the bore<\/td><td>Millimeters or inches<\/td><\/tr><tr><th scope=\"row\">Wall thickness<\/th><td>Half the difference between OD and ID<\/td><td>Millimeters or inches<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Wall thickness links the two diameters, and it carries both the tube and the reinforcement. Because a wire reinforced wall is stiff, a thin wall on a large bore can still resist pressure. The trade is flexibility, and that is the subject of the next column.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"how-bend-radius-and-unit-weight-drive-installation\">How Bend Radius and Unit Weight Drive Installation<\/h2>\n\n\n\n<p>Bend radius is the tightest curve a steam hose can take without kinking or damaging its reinforcement. A steel wire layer resists collapse, so a wire reinforced hose can often hold a smaller bend than a soft textile hose of the same bore. That advantage disappears if the installer bends it below the stated minimum.<\/p>\n\n\n\n<p>The published bend radius is a minimum, and it applies to a static run. Pulling the hose straight around a sharp corner strains the wire layer and the tube at the same time. When a route is tight, calculate the arc before you cut the run. The <a href=\"https:\/\/www.henghuahose.com\/de\/hydraulic-hose-bend-radius-calculation-guide\/\" target=\"_blank\" rel=\"noopener\">bend radius calculation guide<\/a> walks through the geometry for a curved run.<\/p>\n\n\n\n<p>Unit weight per length is the second installation number. It sets the load on hangers and the effort of moving the hose by hand. Long runs sag under their own weight, and a sagging steam hose traps condensate at the low point. Support spacing should always come from the stated unit weight rather than from a rule of thumb.<\/p>\n\n\n\n<p>Table 3. Bend radius and unit weight in steam hose installation planning.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Property<\/th><th scope=\"col\">Why the installer cares<\/th><th scope=\"col\">Related check<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Mindestbiegeradius<\/th><td>Prevents kinking at a tight turn<\/td><td>Routing drawing and support spacing<\/td><\/tr><tr><th scope=\"row\">Unit weight<\/th><td>Sets the load on hangers<\/td><td>Support and hanger design<\/td><\/tr><tr><th scope=\"row\">Coil or length<\/th><td>Sets the number of joints<\/td><td>Joint and drain planning<\/td><\/tr><tr><th scope=\"row\">Cover finish<\/th><td>Handles abrasion and drainage<\/td><td>Guard and drainage path<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>A steam line should drain toward a trap, never toward a low point. Bend radius and support spacing work together here. A generous bend and even support keep the run sloping and keep condensate moving.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"reading-working-pressure-on-a-steel-wire-reinforced-steam-hose\">Reading Working Pressure on a Steel Wire Reinforced Steam Hose<\/h2>\n\n\n\n<p>Working pressure is the continuous limit the hose is designed to hold in normal service. Catalog sheets often print the same figure as the service rating; the failure figure appears as the burst rating. On a steam hose datasheet it never stands alone. It is always tied to a reference temperature, because the allowable pressure falls as temperature rises.<\/p>\n\n\n\n<p>Public hose catalogs state the rated pressure at a reference temperature near 70 \u00b0F (21 \u00b0C). The same convention appears across the industry, and some makers use a different reference near 100 \u00b0F. That difference is why you should read the reference line, not just the headline figure. The <a href=\"https:\/\/www.henghuahose.com\/de\/working-pressure-vs-burst-pressure\/\" target=\"_blank\" rel=\"noopener\">service rating versus burst rating comparison<\/a> explains how the two figures relate.<\/p>\n\n\n\n<p>Saturated steam complicates the reading further. Its temperature and pressure are not independent variables; they are locked together by the saturation curve. At 6 bar g the saturation temperature is 165.0 \u00b0C, and at 18 bar g it is 209.8 \u00b0C. You read a steam duty by picking the pressure, finding its saturation temperature, and comparing that temperature with the hose limit.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-working-pressure-vs-burst-pressure.jpg\" alt=\"diagram comparing working pressure and burst pressure on a steel wire reinforced steam hose rating scale\" class=\"wp-image-6443\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-working-pressure-vs-burst-pressure.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-working-pressure-vs-burst-pressure-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-working-pressure-vs-burst-pressure-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-working-pressure-vs-burst-pressure-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-working-pressure-vs-burst-pressure-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 2. How the service rating, the burst rating, and the safety margin sit on one scale for a steam hose.<\/p>\n\n\n\n<p>Table 4 lists the saturated steam pressure and temperature pairs used throughout this guide. Each pair is a single operating condition, not two free choices. Pressures are gauge values; absolute pressure is the gauge figure plus 1.013 bar. Use it to convert a line pressure into the temperature the hose must survive.<\/p>\n\n\n\n<p>Table 4. Saturated steam pressure and temperature pairs for steam hose selection.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Pressure (bar g)<\/th><th scope=\"col\">Saturation temperature (\u00b0C)<\/th><th scope=\"col\">Saturation temperature (\u00b0F)<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">6<\/th><td>165.0<\/td><td>329.0<\/td><\/tr><tr><th scope=\"row\">10<\/th><td>184.1<\/td><td>363.4<\/td><\/tr><tr><th scope=\"row\">14<\/th><td>198.3<\/td><td>389.0<\/td><\/tr><tr><th scope=\"row\">18<\/th><td>209.8<\/td><td>409.7<\/td><\/tr><tr><th scope=\"row\">20<\/th><td>214.9<\/td><td>418.8<\/td><\/tr><tr><th scope=\"row\">25<\/th><td>226.1<\/td><td>438.9<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>Read the table as a two-step check. First locate your line pressure in the left column. Then read across to the saturation temperature and compare it with the hose temperature limit. If the pair exceeds the limit, a larger construction or a different hose body is needed.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"burst-pressure-and-what-the-hydrostatic-test-proves\">Burst Pressure and What the Hydrostatic Test Proves<\/h2>\n\n\n\n<p>Burst pressure is the pressure at which the hose actually fails. It is measured by a water hydrostatic test under ISO 1402, not by a calculation. The gap between the service rating and the burst rating is the safety margin, and it is large by design.<\/p>\n\n\n\n<p>ISO 6134 governs rubber hoses and hose assemblies for saturated steam. It defines two types. Type 1 is a low-pressure steam hose with a textile reinforcement, rated to 0.6 MPa (6 bar) at 164 \u00b0C. Type 2 is a high-pressure steam hose with a steel wire reinforcement, rated to 1.8 MPa (18 bar) at 210 \u00b0C. A steel wire reinforced steam hose sits in the Type 2 family.<\/p>\n\n\n\n<p>Table 5. The two pressure figures on a steam hose rating sheet.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Term<\/th><th scope=\"col\">What it describes<\/th><th scope=\"col\">Condition it references<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Service rating<\/th><td>The continuous service limit<\/td><td>A stated reference temperature<\/td><\/tr><tr><th scope=\"row\">Burst pressure<\/th><td>The pressure at which the hose fails<\/td><td>A water hydrostatic test<\/td><\/tr><tr><th scope=\"row\">Safety margin<\/th><td>The reserve between the two figures<\/td><td>A standard or catalog convention<\/td><\/tr><tr><th scope=\"row\">Assembly rating<\/th><td>The limit of the finished assembly<\/td><td>The end fitting and coupling method<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>The reporting habit matters as much as the test. A supplier should publish the service rating, the reference temperature, and the burst figure together. A single headline number without the reference temperature cannot be compared with another supplier&#8217;s sheet. For steam service, a wire reinforced hose such as the <a href=\"https:\/\/www.henghuahose.com\/de\/product\/epdm-high-temperature-steam-hose-230%e2%84%83\/\" target=\"_blank\" rel=\"noopener\">EPDM high-temperature steam hose<\/a> gives a realistic upper bound for saturated steam duty.<\/p>\n\n\n\n<p>ISO 1402 covers the hydrostatic test that verifies burst strength, and ISO 4023 covers the steam hose test method. The hose is pressurized with water rather than steam during the test, which keeps the stored energy low and the test controlled. Those two standards, read together, define what a burst rating means in practice.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"how-to-read-a-pressure-rating-chart-column-by-column\">How to Read a Pressure Rating Chart Column by Column<\/h2>\n\n\n\n<p>A pressure rating chart is a table that lines a property up against each size or construction in a range. You read it in two moves: down to the row for your size, then across to the column for the value you need. The chart describes the hose body, and that is its main limit.<\/p>\n\n\n\n<p>Charts differ in how they treat temperature. Some print the rated pressure at one reference temperature and add a separate correction for higher temperatures. Others list a rated pressure for each temperature band directly. Either way, confirm which convention the chart uses before you compare two charts. The steam hose and saturated steam guide explains why steam changes the reading.<\/p>\n\n\n\n<figure class=\"wp-block-image size-full\"><img decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-rating-vs-temperature-reading.jpg\" alt=\"chart showing a steam hose pressure rating read against rising saturated steam temperature\" class=\"wp-image-6444\" srcset=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-rating-vs-temperature-reading.jpg 800w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-rating-vs-temperature-reading-300x225.jpg 300w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-rating-vs-temperature-reading-768x576.jpg 768w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-rating-vs-temperature-reading-16x12.jpg 16w, https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steam-hose-rating-vs-temperature-reading-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p>Figure 3. Reading a pressure rating chart against saturated steam temperature, where the pair moves together.<\/p>\n\n\n\n<p>For saturated steam, the chart and the saturation curve must agree. If your line runs at 10 bar g, the steam sits at 184.1 \u00b0C, and the hose must hold both together. Checking pressure alone can leave you with a hose that is rated for the pressure but not the temperature.<\/p>\n\n\n\n<p>A rating chart is a summary, so it hides detail. It rarely shows the assembly rating, and it rarely shows how a fitting changes the limit. Use it to shortlist a size, then confirm the finished assembly with the supplier before you release the order.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"why-an-assembly-rates-lower-than-the-hose-body\">Why an Assembly Rates Lower Than the Hose Body<\/h2>\n\n\n\n<p>The hose body rating is measured on the hose alone. Once a fitting is attached, the joint becomes part of the pressure boundary and can lower the allowable pressure. This is why a catalog value and an assembly rating can differ by a meaningful margin.<\/p>\n\n\n\n<p>ISO 6134 covers hose assemblies with metal end fittings, which is the correct frame for steam service. Steam practice requires a dedicated coupling at the joint, and a bolt-on safety clamp is the common choice for a steam line. A band or a plain clamp sits outside that frame, so the assembly figure applies only to a hose fitted with a proper coupling.<\/p>\n\n\n\n<p>The reinforcement layer itself is the subject of the companion page on wire braided steam hose (planned URL, publish before linking). That page covers how the wire layer is built; this page stays with the reading of the numbers.<\/p>\n\n\n\n<p>Table 6. End connection options for a steam hose assembly and their effect on the rating.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">End connection<\/th><th scope=\"col\">Common steam use<\/th><th scope=\"col\">Effect on the assembly rating<\/th><\/tr><\/thead><tbody><tr><th scope=\"row\">Bolt-on safety clamp<\/th><td>Slip-on couplings on steam lines<\/td><td>Keeps a rated assembly when fitted correctly<\/td><\/tr><tr><th scope=\"row\">Flange<\/th><td>Fixed headers and manifolds<\/td><td>Adds a bolted joint to inspect<\/td><\/tr><tr><th scope=\"row\">Threaded fitting<\/th><td>Small steam tools and lances<\/td><td>Adds a threaded seal to maintain<\/td><\/tr><tr><th scope=\"row\">Band or plain clamp<\/th><td>Not a substitute for a steam coupling<\/td><td>Can reduce the assembly rating<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p>The lesson is simple. Buy a hose body with the rating you need, then confirm the assembly rating that the finished hose will actually carry. Ask for both figures on the same sheet, from the same supplier, at the same reference temperature.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"handling-storage-and-condensate-drainage\">Handling, Storage, and Condensate Drainage<\/h2>\n\n\n\n<p>A steam hose that is stored badly fails early. Coil the hose to a diameter above its minimum bend radius, and never hang a coiled hose on a sharp hook. Ultraviolet light and ozone age the cover, so keep long-term storage out of direct sun and away from running electrical equipment.<\/p>\n\n\n\n<p>Condensate is the other quiet hazard. Steam cools inside a shut-down line and leaves water at the low point. That water can flash back into steam when the line restarts, so the standard practice for steam hose is to drain the hose after each use. A sloped run and a drain at the low point make that habit easy.<\/p>\n\n\n\n<p>Steam service requires a hose that is labeled for steam duty. A hose built for water, air, or chemicals can look similar and still carry no steam rating at all. The label and the rating sheet are the two things to check before a hose goes onto a steam line.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"choosing-the-right-steel-wire-reinforced-steam-hose\">Choosing the Right Steel Wire Reinforced Steam Hose<\/h2>\n\n\n\n<p>Start with the flow, then the bore, then the wall, and only then the rating block. Match the bore to the steam flow, the rating to the saturated steam pair, and the end fitting to the assembly requirement. A steel wire reinforced steam hose that fits the line but fails at the coupling is still a failed project.<\/p>\n\n\n\n<p>Read the datasheet from the inside out, check the reference temperature, and confirm the assembly rating with your supplier. That short checklist covers the failures that matter most on a steam line. Sizing a hose for a fixed header and replacing one on a small steam tool follow the same reading order. Send the bore you need together with the pressure and temperature pair, and the construction can be matched to that duty.<\/p>\n\n\n\n<p><a href=\"https:\/\/www.henghuahose.com\/de\/contact\/\" target=\"_blank\" rel=\"noopener\">Get a quote and free samples<\/a><\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"steel-wire-reinforced-steam-hose-faqs\">Steel Wire Reinforced Steam Hose FAQs<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-does-the-steel-wire-reinforcement-add-to-a-steam-hose\">What does the steel wire reinforcement add to a steam hose?<\/h3>\n\n\n\n<p>Steel wire reinforced steam hose is a rubber steam hose whose load-bearing layer is steel wire rather than textile. ISO 6134 calls this construction the high-pressure type, Type 2, rated to 18 bar at 210 \u00b0C. The wire carries internal pressure and resists collapse, while an EPDM tube handles the saturated steam.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-do-i-read-the-rated-pressure-on-a-steam-hose\">How do I read the rated pressure on a steam hose?<\/h3>\n\n\n\n<p>Read the rated pressure at the reference temperature the sheet prints; the common industry value is 70 \u00b0F (21 \u00b0C). For saturated steam the rating pairs with a temperature through the saturation curve instead of standing alone. Confirm that pair against your real line pressure and temperature before you accept the figure.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-is-the-difference-between-the-service-rating-and-the-burst-rating\">What is the difference between the service rating and the burst rating?<\/h3>\n\n\n\n<p>A service rating is the pressure a hose may carry continuously; the burst rating is the point at which it fails. The two come from different procedures, because the service figure is set by the maker at a reference temperature while the burst figure is verified under ISO 1402 with a water test. The gap between them is the safety margin, so a sheet that prints only one of the two is only half a specification.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-is-a-rating-chart\">What is a rating chart?<\/h3>\n\n\n\n<p>A rating chart is a published table of sizes and values for one product family, so it describes the hose body rather than the finished assembly. When two charts disagree for the same bore, compare the reference temperature first, then the reinforcement and the end fitting each chart assumes. Neither figure is automatically safer.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"why-is-the-assembly-rating-lower-than-the-hose-body-rating\">Why is the assembly rating lower than the hose body rating?<\/h3>\n\n\n\n<p>A hose body is tested on its own, so the published figure stops at the tube end. Every attachment method adds a pressure boundary of its own: a crimped ferrule, a clamped coupling, and a threaded fitting are three different boundaries with three different limits. Because the weakest link governs, the assembly rating is the figure that belongs on the line.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"does-a-higher-steam-pressure-always-mean-a-higher-temperature\">Does a higher steam pressure always mean a higher temperature?<\/h3>\n\n\n\n<p>For saturated steam, yes. Pressure and temperature move together on the saturation curve, so 6 bar g is about 165 \u00b0C and 18 bar g is about 209.8 \u00b0C. The two cannot be chosen independently. Only superheated steam and hot water let you set temperature and pressure as separate variables.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-is-a-steam-hose-pressure-tested\">How is a steam hose pressure tested?<\/h3>\n\n\n\n<p>Steam hose burst and verification testing uses a water hydrostatic test under ISO 1402. ISO 4023 sets out the test method for the hose itself. The test fills the hose with water, never steam, because water stores far less energy than compressed steam at the same pressure. That keeps the test controlled and repeatable.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-size-steam-hose-do-i-need\">What size steam hose do I need?<\/h3>\n\n\n\n<p>Start from the flow you need and the steam velocity you can accept, then choose the smallest bore that keeps pressure drop reasonable. Check that the outside diameter fits your clamps and guards, and that the bend radius suits your routing. Convert between millimeters and inches before ordering to avoid a mismatched coupling.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-much-does-a-steam-hose-weigh\">How much does a steam hose weigh?<\/h3>\n\n\n\n<p>Weight per unit length matters because it loads the hangers and sets how many people the job takes. A small bore in a long run stays manageable, while a large bore turns heavy quickly. Take the support spacing from the printed figure instead of a generic interval.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"can-i-use-a-band-or-plain-clamp-on-a-steam-hose\">Can I use a band or plain clamp on a steam hose?<\/h3>\n\n\n\n<p>No. A band or a plain clamp falls outside the ISO 6134 frame for a steam assembly, and the rated figure printed for the hose body assumes a proper coupling. Ask the supplier to state the assembly limit for the exact coupling and attachment method you intend to use, because that is the number your line will actually see.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"about-henghua\">\u00dcber HENGHUA<\/h2>\n\n\n\n<p>HENGHUA is a professional hose and fitting manufacturer supplying distributors, retailers, and OEM brands worldwide. The steam hose line is built around an EPDM tube, with either a textile or a steel wire reinforcement layer and a pin-pricked cover for steam service. Catalog steam hoses include an EPDM steam hose for 170 \u00b0C and an EPDM high-temperature steam hose for 230 \u00b0C.<\/p>\n\n\n\n<p>End connections can be supplied as clamped safety couplings, flanges, or threaded fittings to suit the duty. Factory assembly, custom lengths, jacket printing, and private label or OEM\/ODM options are available. Commercial terms are factory-direct pricing, short lead times on volume, and a warranty.<\/p>","protected":false},"excerpt":{"rendered":"<p>A steel wire reinforced steam hose is specified by its inside diameter, outside diameter, tolerance, bend radius, unit weight, working pressure, and burst pressure. Reading those fields in the right order prevents the most common sizing error on a steam line. ISO 6134 rates this construction as Type 2, the high-pressure type, at 1.8 MPa [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":6445,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_surecart_dashboard_logo_width":"180px","_surecart_dashboard_show_logo":true,"_surecart_dashboard_navigation_orders":true,"_surecart_dashboard_navigation_invoices":true,"_surecart_dashboard_navigation_subscriptions":true,"_surecart_dashboard_navigation_downloads":true,"_surecart_dashboard_navigation_saved":true,"_surecart_dashboard_navigation_billing":true,"_surecart_dashboard_navigation_account":true,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[1],"tags":[2500,2522,2523,2521,2177],"class_list":["post-6476","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-burst-pressure","tag-pressure-rating-chart","tag-steam-hose-specs","tag-steel-wire-reinforced-steam-hose","tag-working-pressure"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v24.5 (Yoast SEO v28.1) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>Steel Wire Reinforced Steam Hose: Specs and Ratings<\/title>\n<meta name=\"description\" content=\"Steel wire reinforced steam hose specs: bore, outside diameter, bend radius, working pressure and burst pressure, and how to read the pressure rating chart.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.henghuahose.com\/de\/steel-wire-reinforced-steam-hose\/\" \/>\n<meta property=\"og:locale\" content=\"de_DE\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings\" \/>\n<meta property=\"og:description\" content=\"Steel wire reinforced steam hose specs: bore, outside diameter, bend radius, working pressure and burst pressure, and how to read the pressure rating chart.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.henghuahose.com\/de\/steel-wire-reinforced-steam-hose\/\" \/>\n<meta property=\"og:site_name\" content=\"HENGHUA\" \/>\n<meta property=\"article:published_time\" content=\"2026-10-19T01:45:25+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-10-19T01:45:28+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steel-wire-reinforced-steam-hose-hero.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"goodheart786@gmail.com\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Verfasst von\" \/>\n\t<meta name=\"twitter:data1\" content=\"goodheart786@gmail.com\" \/>\n\t<meta name=\"twitter:label2\" content=\"Gesch\u00e4tzte Lesezeit\" \/>\n\t<meta name=\"twitter:data2\" content=\"16\u00a0Minuten\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"TechArticle\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/\"},\"author\":{\"name\":\"goodheart786@gmail.com\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\"},\"headline\":\"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings\",\"datePublished\":\"2026-10-19T01:45:25+00:00\",\"dateModified\":\"2026-10-19T01:45:28+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/\"},\"wordCount\":3247,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/steel-wire-reinforced-steam-hose-hero.jpg\",\"keywords\":[\"burst pressure\",\"pressure rating chart\",\"steam hose specs\",\"steel wire reinforced steam hose\",\"working pressure\"],\"articleSection\":[\"Blog\"],\"inLanguage\":\"de\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/\",\"name\":\"Steel Wire Reinforced Steam Hose: Specs and Ratings\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/steel-wire-reinforced-steam-hose-hero.jpg\",\"datePublished\":\"2026-10-19T01:45:25+00:00\",\"dateModified\":\"2026-10-19T01:45:28+00:00\",\"description\":\"Steel wire reinforced steam hose specs: bore, outside diameter, bend radius, working pressure and burst pressure, and how to read the pressure rating chart.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#breadcrumb\"},\"inLanguage\":\"de\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"de\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/steel-wire-reinforced-steam-hose-hero.jpg\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/10\\\/steel-wire-reinforced-steam-hose-hero.jpg\",\"width\":800,\"height\":600,\"caption\":\"A coiled black rubber steam hose on a gray concrete floor\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/steel-wire-reinforced-steam-hose\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.henghuahose.com\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#website\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"name\":\"HENGHUA\",\"description\":\"Powering Your Industry, Worldwide.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\"},\"alternateName\":\"HENGHUA Hose\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.henghuahose.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"de\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#organization\",\"name\":\"HENGHUA\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"de\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"contentUrl\":\"https:\\\/\\\/www.henghuahose.com\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/HENGHUA-Hose-Manufacturer-Logo.png\",\"width\":388,\"height\":90,\"caption\":\"HENGHUA\"},\"image\":{\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.henghuahose.com\\\/#\\\/schema\\\/person\\\/28fdea90953f1958bdc26b600560c5c7\",\"name\":\"goodheart786@gmail.com\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"de\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g\",\"caption\":\"goodheart786@gmail.com\"},\"sameAs\":[\"https:\\\/\\\/henghuahose.com\"],\"url\":\"https:\\\/\\\/www.henghuahose.com\\\/de\\\/author\\\/goodheart786gmail-com\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Steel Wire Reinforced Steam Hose: Specs and Ratings","description":"Steel wire reinforced steam hose specs: bore, outside diameter, bend radius, working pressure and burst pressure, and how to read the pressure rating chart.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.henghuahose.com\/de\/steel-wire-reinforced-steam-hose\/","og_locale":"de_DE","og_type":"article","og_title":"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings","og_description":"Steel wire reinforced steam hose specs: bore, outside diameter, bend radius, working pressure and burst pressure, and how to read the pressure rating chart.","og_url":"https:\/\/www.henghuahose.com\/de\/steel-wire-reinforced-steam-hose\/","og_site_name":"HENGHUA","article_published_time":"2026-10-19T01:45:25+00:00","article_modified_time":"2026-10-19T01:45:28+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steel-wire-reinforced-steam-hose-hero.jpg","type":"image\/jpeg"}],"author":"goodheart786@gmail.com","twitter_card":"summary_large_image","twitter_misc":{"Verfasst von":"goodheart786@gmail.com","Gesch\u00e4tzte Lesezeit":"16\u00a0Minuten"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"TechArticle","@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#article","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/"},"author":{"name":"goodheart786@gmail.com","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7"},"headline":"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings","datePublished":"2026-10-19T01:45:25+00:00","dateModified":"2026-10-19T01:45:28+00:00","mainEntityOfPage":{"@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/"},"wordCount":3247,"commentCount":0,"publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"image":{"@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steel-wire-reinforced-steam-hose-hero.jpg","keywords":["burst pressure","pressure rating chart","steam hose specs","steel wire reinforced steam hose","working pressure"],"articleSection":["Blog"],"inLanguage":"de","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/","url":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/","name":"Steel Wire Reinforced Steam Hose: Specs and Ratings","isPartOf":{"@id":"https:\/\/www.henghuahose.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#primaryimage"},"image":{"@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#primaryimage"},"thumbnailUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steel-wire-reinforced-steam-hose-hero.jpg","datePublished":"2026-10-19T01:45:25+00:00","dateModified":"2026-10-19T01:45:28+00:00","description":"Steel wire reinforced steam hose specs: bore, outside diameter, bend radius, working pressure and burst pressure, and how to read the pressure rating chart.","breadcrumb":{"@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#breadcrumb"},"inLanguage":"de","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/"]}]},{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#primaryimage","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steel-wire-reinforced-steam-hose-hero.jpg","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/10\/steel-wire-reinforced-steam-hose-hero.jpg","width":800,"height":600,"caption":"A coiled black rubber steam hose on a gray concrete floor"},{"@type":"BreadcrumbList","@id":"https:\/\/www.henghuahose.com\/steel-wire-reinforced-steam-hose\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.henghuahose.com\/"},{"@type":"ListItem","position":2,"name":"Steel Wire Reinforced Steam Hose: Specs and Pressure Ratings"}]},{"@type":"WebSite","@id":"https:\/\/www.henghuahose.com\/#website","url":"https:\/\/www.henghuahose.com\/","name":"HENGHUA","description":"Wir versorgen Ihre Branche weltweit mit Energie.","publisher":{"@id":"https:\/\/www.henghuahose.com\/#organization"},"alternateName":"HENGHUA Hose","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.henghuahose.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"de"},{"@type":"Organization","@id":"https:\/\/www.henghuahose.com\/#organization","name":"HENGHUA","url":"https:\/\/www.henghuahose.com\/","logo":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","contentUrl":"https:\/\/www.henghuahose.com\/wp-content\/uploads\/2026\/05\/HENGHUA-Hose-Manufacturer-Logo.png","width":388,"height":90,"caption":"HENGHUA"},"image":{"@id":"https:\/\/www.henghuahose.com\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/www.henghuahose.com\/#\/schema\/person\/28fdea90953f1958bdc26b600560c5c7","name":"goodheart786@gmail.com","image":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/e1786ba73a3780e524c9584c9578a9c8d9baa7e82407695918f6b784c79979bf?s=96&d=mm&r=g","caption":"goodheart786@gmail.com"},"sameAs":["https:\/\/henghuahose.com"],"url":"https:\/\/www.henghuahose.com\/de\/author\/goodheart786gmail-com\/"}]}},"_links":{"self":[{"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/posts\/6476","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/comments?post=6476"}],"version-history":[{"count":1,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/posts\/6476\/revisions"}],"predecessor-version":[{"id":6494,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/posts\/6476\/revisions\/6494"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/media\/6445"}],"wp:attachment":[{"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/media?parent=6476"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/categories?post=6476"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.henghuahose.com\/de\/wp-json\/wp\/v2\/tags?post=6476"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}